Optic Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
Optical Power Meter - MATRIQ
1400 Series
Power Meter
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
Product
Fiber Optic Multimeters
-
Years ago, testing fiber optic connections required a fiber optic power meter and fiber optic light source. These two pieces of equipment were carried side-by-side and used together to verify a fiber optic connection was working.
-
Product
Fiber Optic Sensing Instrument
Static Strain
-
Static Strain is a low cost one-channel fiber optic sensing instrument for quasi-continuous strain monitoring. With over 2,000 sensing points on a single fiber, users are able to achieve spatially continuous real-time strain monitoring.
-
Product
Optical Signal Conditioning Products
-
The single-mode fiber N7761A, N7762A and N7764A provide 1, 2 or 4 attenuation channels in a compact remote-controlled instrument. These attenuators provide very fast adjustment and have built-in output power monitoring for accurate power setting and control, as needed for receiver sensitivity testing or in system simulations.
-
Product
Optical Test
-
Optical components such as micro-lenses, diffractive optical elements (DOE), meta optical elements (MOE) and micro lens arrays (MLA) are now largely used on consumer electronics and even more optical elements need to be integrated into smaller and smaller packages. Nowadays mass-production industries key to success lies in increasing the yield by means of strongly automatized testing machines, with statistical analysis.
-
Product
Satellite Optical Transmitter
SST-15CW
-
Hangzhou Softel Optic Co., Ltd.
* Designed for satellite optical system*Wide operating frequency range: 47-2150MHz*Excellent linearity and flatness*Using 1-core single-mode fiber, high return loss*Build-in CWDM, using DFB coaxial small package laser*Output 13/18V, 0/22KHz to LNB working*ALNB mode switch offers the possibility to use either Quattro or QUAD LNB*A distribution of up to 16 optical nodes is possible*Red-LED for power indication*Smaller size and easier installation
-
Product
Broadband Power Amplifier
PAS-00260-10
-
* Solid State Power Amplifier* Gain : 49 dB typ.* High IP3, 50.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Type N Connectors
-
Product
Optical / Electrical Clock Recovery
N1078A
Clock and Data Recovery Unit
N1078A Optical/Electrical Clock Recovery provides standards-compliant clock recovery capabilities for single-mode optical as well as electrical signals from 125 MBd up to 64 GBd PAM4 and NRZ
-
Product
hpower High Power Amplifiers
-
For hpower high-power actuators, high-power amplifiers are required. Together these hpower actuators and amplifier systems deliver exceptionally fast response times, superior dynamics, high force generation, and nanometer precision.
-
Product
HF Low Noise Amplifier
-
The COMM-connect HF Low Noise Amplifier can be used to amplify signals in the HF frequency range. The amplifier comes with a selection of 4 different connectors, which makes it very easy to adapt to any type of installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
Optical Components
-
ZYGO Corporation was founded in 1970 by Paul Forman, Sol Laufer, and Carl Zanoni with the vision to become the premier manufacturer of plano optical components through the application of innovative polishing methods. We have realized our founders vision, and further expanded our manufacturing offering beyond plano optical components to include coatings, aspheres, freeforms and complex optical systems.
-
-
Product
Lock-in Amplifier
HF2LI
-
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
-
-
Product
Simulating Optical Design Components
Wave Optics Module
-
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
Product
Optical Power Multimeter
TM503N
-
TM503N Optical Power MultiMeter, a new generation of high-performance optical network test meter, with the characteristics of excellent performance and fast filed–test, has adopted the latest laser exploration and processing technology. It is a compositive optical power meter aimed at optical network maintenance, equipment research and development.
-
Product
Automated Optical Inspection (AOI)
TR7700 SIII 3D
-
TRI’s ground breaking 3D AOI solution delivers the fastest hybrid PCB inspection combining optical and blue-laser-based true 3D profile measurement for the highest automated defect symptom coverage possible. Integrated state-of-the-art software solution and third generation intelligent hardware platform offer stable and robust 3D solder and component defect inspection and with high inspection coverage and easy programming.
-
Product
High Speed Optical Choppers
-
The Optical Choppers offered by Hinds Instruments are resonant devices designed to work at one frequency. We offer two ways to chop light: a High Speed Optical Chopper (HSOC) and a Photoelastic Modulator (or PEM).
-
Product
Fiber Optic Sensors And Fiber Optics
-
Over 350 customized fiber optic solutions. Smaller, more precise, faster. Robust - High-temperature, chemically resistant, mechanically robust glass or plastic fibers. Better performance - Position-independent detection of irregular objects or liquids. Plug & Play - Intuitive parametrization with the Baumer Sensor Suite via IO-Link.
-
Product
Low Noise, High Performance, FTTP High Power Multi-port Optical Amplifier with a Gain Spectrum Band
MX5800 Series
-
Each output port for the optical amplifier has built-in high performance CWDM. Every external up-link optical port of the optical amplifier can conveniently connect with an OLT. Each of the 1550nm (CATV)’s output optical ports will multiplex 1310/1490n’s data stream from an external OLT, reducing the quantity of the components and improving the performance and reliability of the system.
-
Product
Gain Block Amplifiers
-
Qorvo designs and manufactures a wide selection of general-purpose, internally matched MMIC amplifiers that are targeted for many applications in network infrastructure and defense / aerospace. These components showcase the wide range of performance capabilities using Qorvo's processes. Our general-purpose gain blocks are internally matched and offer various gain and linearity levels in a variety of package types, giving customers many options for system design.
-
Product
Optical Tensiometers
Theta High Pressure
-
The Attension® Theta High Pressure is a tensiometer for measuring wettability and interfacial tension at high pressures and high temperatures within enhanced oil recovery research. With the harsh conditions of an oil reservoir in mind, the instrument is designed to ensure ease of use and yet offer wide measurement possibilities.
-
-
Product
Active Optics
-
Radiall designs and manufactures end-to-end optical links for massive data transfers in harsh environments.
-
Product
Optical Sensor
-
Sendot develops and produces optical sensors that measure with light. Our optics are unique, our intelligent electronics direct the measurements and convert them into measurement results.
-
Product
Amplifiers
-
Commercial grade indoor distribution amplifier, 54-870 MHz forward gain of 30 dB, 5-42 MHz reverse gain of 20 dB, forward path slope and gain controls with separate reverse path gain control
-
Product
Single Channel High Voltage Linear Amplifier
F10A
-
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
-
Product
4 Channel Variable Gain Fast Amplifier
V974
-
The Mod. V974 is a 4 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a voltage gain adjustable from 1 to 10 in x1 steps. Channels are non-inverting and bipolar: they amplify both positive and negative signals.
