Sensor Testers
-
Product
Outdoor Temperature Sensor
ENVIROMUX-STS-O
-
Applications from -40 to 185°F (-40 to 85°C). Accurate to within ±0.9°F (±0.5°C). Weatherproof enclosure. High resistance to external influences on the cable due to digital output signal. Re-calibration is not necessary after initial set-up. Quick release waterproof RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,942,123 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
Self-Adhesive Clips for Liquid/Chemical Sensor Rope
ENVIROMUX-CLP10-LD
-
Use to prevent sensor rope cable from shifting after installation. Self-adhesive backing for easy installation. Material: Nylon. Quantity: 10 clips. Compatible with ENVIROMUX-LDSx-y, ENVIROMUX-CDSx-y, ENVIROMUX-LDx-y and ENVIROMUX-CDx-y.
-
Product
Load Cells, Weighing and Force Sensors
-
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
Product
Static Tester
-
Electrostate tester with LED indicator for the detection of static charge in the plus and minus range. An indispensable, inexpensive tool for the assessment and selection of materials in the living area, as well as the quality of the room climate.Buy Data Sheet
-
Product
SRJ (for IBP sensors)
-
The MEDTEQ SRJ is a test jig to measuring the step response of IBP sensors, which can assist in testing compliance with IEC 60601-2-34 frequency response. It is also suitable for manufacturers or test labs wanting to access the raw pressure waveforms via an oscilloscope.
-
Product
Oxygen Sensors
-
The protective membrane in front of the oxygen sensor can be heated to prevent water from condensing on the membrane and blocking the diffusion path. The heater is typically used when sensors are deployed in soil or compost where relative humidity is close to 100 %.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Inertial & Tilt Sensors
-
Jewell Instruments is a world leader in the design, manufacture, and distribution of high-precision accelerometer and inclinometer sensors for tilt and acceleration applications. We also provide custom-engineered sensors for specific application solutions.
-
Product
SparkFun Load Sensor Combinator
-
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat's nest of wires. The Load Sensor Combinator was created to combine the 12 wires found in a bathroom scale into the standard four-wire Wheatstone bridge configuration.
-
Product
Torque Tester
DIS-IP Series (-IP05/5/50/200/500)
-
For managing various manual torque wrenches and torque drivers. Standard product for static torque measurement. Display characters are larger, improving usability. Installation in a small space is now possible with the separated type. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
Product
Desktop Material Testers
-
Desktop force/displacement testers record both force and displacement. Programming is facilitated by the unique program dial using plain language menu screens.The jog movement moves the sensor .05mm for each click of the program dial (under no load).
-
Product
AMIDA IGBT Tester
600
-
KVI Source: 1 Channel 4Q V/I Source; ±1000V, ±10mA Source ability; V/I read back at 16 bits resolutions under 100Ks sampling rate ; ±0.2% accurate reading of Range
-
-
Product
Insulation Tester (For Telecoms)
1801 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Solid state circuitry.● Battery check feature.● Automatic circuit discharge.● Three insulation test voltages.● Color-coded scale.● AC voltage measurement.● Fuse protected.
-
Product
Split type AC Current Sensor
CTF-200A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
*Laser Thermal Power Sensors
-
Thermal sensors have a series of bimetallic junctions called a thermopile. Radial or axial heat flow through the sensor creates a voltage proportional to the power absorbed as it flows through the thermopile. The reading is not dependent on the ambient temperature since only the temperature difference is measured and not the absolute temperature. The thermopile elements are so arranged that the reading is almost independent of beam size and position. Generally, Ophir specifies ±2% or better uniformity of reading over the surface.
-
Product
Dielectric Withstand Tester
-
Weshine Electric Manufacturing Co., Ltd
The induction withstand voltage test of transformers and transformers is an important test to ensure that the quality of transformers conforms to national standards. The longitudinal insulation induction withstand voltage test of the inter-turn, inter-layer, inter-section and inter-phase insulation of the transformer winding is an important item in the transformer insulation test.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
Motion Reference Units And Wave Sensors
MRU And WS
-
The Motion Reference Unit (MRU) product line was first released in 2004 when Inertial Labs MEMS-based sensor solutions began to compete in performance with traditional FOG units. Easy integration of the MRU product line for the end user means competitive performance at no extra cost.
-
Product
Fault Indicators and Sensors
-
Schweitzer Engineering Laboratories, Inc.
This technology detects overcurrent faults on overhead and underground lines to speed up power restoration and enhance protection.
-
Product
HDMI Tester
21-8575-00
-
The HDMI Tester is designed to provide fast convenient verification of proper pin connections of HDMI cables and wall plates. The set includes a Main Test Unit and Remote Test Receiver.
-
Product
Light Measurement Sensors
-
Gamma Scientific offers a catalog of professional light intensity measurement devices for photometric and radiometric applications. These devices are typically utilized by laboratories, OEM’s, value-added resellers and other groups seeking to accurately measure light intensity and brightness. Browse our light intensity measurement device catalogs to find the right photometry or radiometry solution today.
-
Product
Brake Testers
-
Orbit Controls Decelerometers are mobile measuring devices for measuring the braking behavior of road or rail vehicles as well as trailers depending on the braking force and pressure in the air or hydraulic braking system.
-
Product
Wide Area Thrubeam Laser Sensor
LV-H300/100
-
Wide Area Thrubeam Laser Sensor. World's smallest size. Linear area beam (Transmitter). Light diffusion sheet (Receiver). Easy adjustment of beam axis
-
Product
Light-to-Analog Sensors (Current)
-
Renesas' light-to-current silicon optical sensors combine a photodiode array and current amplifiers on a single monolithic IC. These devices are ideal for display and keypad dimming, as well as industrial and medical light sensing applications.
-
Product
Demulsibility Characteristics Testers
-
The Labodam Demulsibility Characteristics Tester is designed an dmade as per Test Methods for Demulsibility Characteristics of Petroleum Oils and Synthetic Fluids ASTM D1401
-
Product
Continuity Tester
4102
-
Peaceful Thriving Enterprise Co Ltd
This product is designed to measure the continuity of electric circuits and components. The measurement result will be indicated by LED and buzzer. The illumination is very helpful when technician is working in dark environment.
-
Product
Magnetfield Testers
-
The magnetic field tester is suitable for rapid and precise testing of electro-magnetic switches and valves. Their tip lights up to indicate the presence of permanent, DC or AC magnetic fields. Thereby, they are so sensitive that very often it is not necessary to remove covers or cladding from machines and the function check can be carried out without any setting-up time or stopping the machine.
-
Product
AC Hipot Tester
295
-
Our Model 295 is a simple-to-use AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). You need a Hipot Tester that includes all the features you need to get the job done, the 295 has what you're looking for. Make testing simple with common sense security settings. PLC Remote allows you to make AC Hipot Testing safer with Personal Protective Equipment (PPE).
-
Product
Sensor
Hyperion Phycocyanin
-
Valeport’s Hyperion Phycocyanin Fluorometer sensor delivers high-performance measurements of Fluorescein, in a compact & robust package ideal as a standalone sensor, for ROV and AUV integration or used as part of a multi-sensor array and data logger.
