-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
IEC60884 Fig38 Thermal Compression Test Device For Plug Testing
IEC60884 fig38
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig38 thermal compression test device for plug testingUsed to evaluate the pressure resistance of electrical accessories and wall mounted mounting boxes under heatStandard: GB2099.1-2008 Articles 24.19 and 25.4 and Figure 38, IEC60884-1 Figure 38, etc.
-
Product
Subrack Enclosures
IEC 60297
-
Beijing Rdekono Electronic Equipment Co.,Ltd.
As a professional 19-Inch Subrack Manufacturer, our Networking Racks and 19-Inch Subracks are meticulously crafted to meet the highest industry standards, ensuring optimal performance and reliability. Designed with precision and attention to detail, our products offer a robust and efficient solution for housing and organizing electronic components.
-
Product
Bounded Output Mask
-
The bounded output mask provides a means of ensuring that measurements of TI according to IEC 62359 can satisfy the requirement of only determining the ultrasonic output through an area of 1 cm x 1 cm.
-
Product
Electrical Button Life Span Tester
IEC60884
-
Shenzhen Autostrong Instrument Co., Ltd.
Plugs and the sockets life tester is designed according to the corresponding provisions of the GB2099-96,GB16915-97 and IEC60884-1,used to detect the mechanical life test of the household and similar purposes of the plugs and the sockets products.
-
Product
K Thermocouple Penetration Probe
TP660
-
“K” Type thermocouple penetration probe. Tolerance according to IEC 60584-2 standard.
-
Product
IEC60950 50mm Impact Test Balls
CX-15
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Impact Test Ball is a specially machined ball to test impact resistance according to IEC, CSA and UL Standards. It is made of chrome-plated-steel for durability, and is fitted with an eyelet to facilitate testing for pendulum applications. Eyelet is threaded to the ball to allow attachment of a handle or force gauge. Weights are closely controlled.
-
Product
LAN Router
ICR-2701-S1
-
ICR-2700-S1, EMEA, 2× Ethernet, USB, Metal, Without Accessories. Security based on IEC 62443-4-2 level 1. 1.3 GB eMMC storage to host customer SW applications.
-
Product
28 Days Test Bench (Single Phase & Three Phase)
-
The SCR Elektroniks 3 station MCB 28 Days and Temperature Rise Test Bench is economically designed to verify the 28 Days Test (21 hr ON, 3 hr OFF Test) as per clause 9.9 of IEC 60898-1 and Temperature Rise of the parts of a Circuit Breaker specified in Table 6 of clause 8.4.1 measured under the conditions specified in clause 9.8.2 of IEC 60898-1.
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
Product
IEC60068-2-75 Impact Spring Hammer Single Energy
CX-T02
-
Shenzhen Chuangxin Instruments Co., Ltd.
Required by many Standards to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC, EN, UL, CSA and other international Standards.
-
Product
Short Test Pin Probe 13
CX-13
-
Shenzhen Chuangxin Instruments Co., Ltd.
Short Test Pin Probe 13 Used to test accessibility through enclosure openings per IEC, EN, UL and CSA Standards.
-
Product
Class 2 Sound Pressure Level Meter
Castle Sonus GA216B
-
This class 2 Sound Level Meter (GA216B) is a feature packed instrument that is fully complient with IEC 61672-1:2002. This meter provides you with the ability to measure sound pressure (Lp) and peak (Cpeak) simultaneously, a requirement for multiple tasks including initial spot-check assessments to the Control of Noise at Work Regulations 2005. The body is designed from tough, crack resistant ABS plastic, ensuring your new Sound Level Meter will survive the conditions for which it was intended. Coming with a high specification measurement microphone which has been calibrated before you receive it, you can be sure your readings are accurate from day one.
-
Product
Tester For The New Digital Grid
Zeus IEC-61850
-
Zeus is a tester designed to install and maintain the communications in the power industry. It supports legacy and new generation interfaces in order to verify Ethernet / IP, PTP, SyncE, ToD, IRIG-B, T1 / E1, C37.94, RS-232, G703 and protocols such as PRP, GOOSE, SV or MMS, therefore you will get a perfect vision and control of your infrastructures improving protection and data acquisition.
-
Product
Thermocouple Cable / Wire
-
Labfacility offer a wide range of thermocouple, PRT and extension cable / wire in stock for immediate despatch. Thermocouple cables are available in IEC or ANSI colour codes. Insulation types include PFA, PTFE, PVC & Fibreglass.
-
Product
Sound Level Meters
-
Complies with IEC 61672-1 class 2 standard, Measures Leq, MaxL, MinL, SPL, 64,000 Records Data Logger, PC interface
-
Product
Plug Socet & Cord Testing
-
Educated Design & Development, Inc.
Flexing Tests: On flexible cables (or cords sets with fitted plugs), electric tools or hand lamps. Meets requirements of standards such as IEC 60335, IEC 60227, IEC 60745 and UL745. This product is for continuous bending tests of cables or cord sets fitted with plugs. The model F39 allows the simultaneous testing of two samples in it's standard version. This not only allows for substantial time savings, but also allows for the testing current circuits to be simplified by looping through the cables.
-
Product
Vibration Test Systems
G-0 Series
-
The G-0 Series Vibration Test Systems consist of all-round, rugged, high quality vibration generators energy-efficient solid-state PWM power amplifiers, ideally suited to any vibration tests requiring high reliability such as MIL, IEC and JIS standardized tests for aircraft, automobiles, electronic components, electric apparatus and aerospace equipment.
-
Product
Vessel For Testing Bob Elements
IEC60335-2-6 Figure101
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-6 Figure 101 Aluminium Test Vessels also conforms to the clause 3.1.9.108 of IEC60335-2-9.The IEC60335-2-6 Figure 101 Aluminium Test Vessels is made of unpolished commercial quality aluminium.
-
Product
Vertically Falling Water Drops Device IPX1/2
IEC60529
-
Shenzhen Chuangxin Instruments Co., Ltd.
This device is designed according to terms and conditions of IEC60529,GB4208-2008,GB7000.1-2007,GB4706.1-2005.Satisfying requirements of level IPX1/2. Applide to test LED lamps and house hold appliances, and other electric and electronic products waterproof test of IP code level IPX 1/2.
-
Product
Glow Wire Test Apparatus
GWT A2
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
