Polarization Extinction Ratio
a measure of the degree of polarization. Also known as: PER
See Also: Fiber Optic Cable Test
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 31.5Ω
40-253-010
Programmable Resistor Module
The 40-253-010 is a programmable resistor module with 2 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
5 Gb/s Programmable Digital Delay Line
QPDDL5
-
The QPDDL5 series delay lines are four channel precision time delay generators for digital signals. Delays are controlled precisely in 5 or 10 ps increments at data rates up to 5 billion bits per second or clock rates exceeding 2.5 GHz. Each of the four channels is independently programmable.
-
Product
Power Quality Analyzer
PQPro
-
The PQPro™ is a portable 8 channel (4 voltage and 4 current) power quality analyzer that can stream high resolution waveform and RMS data to high capacity removable SD memory cards. Sampling rate can be adjusted from 64 samples per cycle to 1024 samples per cycle.
-
Product
QorIQ P5040 Processor AMC, PCIe
AMC704
-
The AMC704 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the NXP P5040 (quad core) processors. The unit provides dual x4 PCIe on Ports 4-7 and 8-11 per AMC.1 and the PCIe interface can be configured in Host or Agent mode.
-
Product
Clean Air Curtain
CAC
-
Clean Air Curtain (CAC) is a compact tabletop air filter device. It creates an invisible air barrier between two persons to prevent transmission of viruses like Covid-19. Conventional air filters focus only on the quantity of air filtered per hour. However, the high-speed clean air jet of CAC ensures that filtered air also mixes well within the room. Since short-cycling is eliminated, CAC offers a much bigger coverage area. CAC is especially useful for personnel working on shop counters & receptions.
-
Product
Digital/Pattern/PE Card
PE32H
Interface Card
The PE32H represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PE32H offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PE32H also supports deep pattern memory by offering 32M of on-board vector memory with dynamic per pin direction control and with test rates up to 66 MHz. With new 32M log memory, PE32H can capture 32 channels data or fail log.
-
Product
Barometric Pressure Sensors
-
Accurate within 1.5 % across a pressure range of 15 to 115 kPa (4.43 to 34.96 in Hg). Long-term non-stability has been measured continuously indoors and in natural conditions (with sensors mounted inside a datalogger enclosure) for multiple sensors and is less than 0.5 % per year. Temperature effects on signal are less than 1 % across a wide temperature range (-20 to 50 C).
-
Product
MO-300 MSATA Module
SQF-SMS 630
Solid-State Drive
SQFlash mSATA 630, SATA Gen. 3 (6.0Gbps) Compliant with SATA III and SATA v 3.0 standard. Supports 72 bit ECC correct per 1K Byte data. Support hardware write protect. Supports Fragment Writing Technology and Flush Manager.
-
Product
SQFlash MSATA 830, SATA Gen. 3 (6.0Gbps)
SQF-SMS 830
Solid-State Drive
Compliant with SATA III and SATA v3.2 standard, Supports 120 bit ECC correct per 2K Byte data. Optional support for AES and voltage stabilizer, Shock resistance, anti-vibration and low power consumption. GUI management tool & software API package.
-
Product
Low Power MIPI Bridging Solution With Integrated Flash
CrossLinkPlus
-
*Instant-on (< 10 ms) configuration with integrated flash memory*Integrated flash enables flexible reprogramming in the field*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per port*11 programmable, source synchronous I/O pairs for camera and display interfacing*Available in small 3.5 mm x 3.5 mm BGA package with 0.4 mm pitch*Comprehensive library of IP and reference designs, compatible with CrossLink
-
Product
High Power Beam Analysis
-
The advantages of fiber lasers are their high power, mechanical stability and good beam quality; however beam quality and beam profile has to be periodically checked. In general, there are many difficulties in checking beam quality especially at the focal point, where densities will exceed 50KWatt per square cm. On one hand those energies are capable of melting and destroying most known materials, while on the other hand measuring a focused profile is the most significant measurement.
-
Product
Transducers For Photodiodes
-
Photodiodes convert incoming electromagnetic radiation into electrical charge carriers. If photodiodes are short circuited an electrical current (photocurrent) proportional to the incident radiation intensity (number of photons per second) is induced. These photocurrents are generally small and cover the range from femtoampere (fA) to microampere (µA). Signal transducers transform this weak photocurrent to robust standard signals for reliable data transmission and simple data acquisition.
-
Product
CO2, CO2 and Temperature Transmitters
HD37…
-
The transmitters of the HD37… series are used mainly in air quality control by measuring CO2 (Carbon Dioxide) in the ventilation systems. This allows you to vary the number of air change per hour according to ASHRAE and IMC norms.
-
Product
3D Sensor
C6 Series
-
The new 3D C6 series by AT is built on a novel sensor platform that supports the latest industrial standard GigE Vision/GenICam 3D at 1 Gbit/s. These new laser profilers offer an impressive combination of extremely fast and highly precise resolution, reaching up to 4,096 points per profile, a profile speed of up to 200 kHz, and high dynamic range 3D image capture. They are available as compact sensors, MCS, and 3D cameras.
-
Product
Immersion Systems
-
Immersion systems are the workhorses of the industry. Our latest NXT machines have shown the ability to run in excess of 6,000 wafers per day, with an average five percent productivity increase over 12 months, supporting our customers' value requirements. We continue to innovate our immersion systems to meet the requirements of future nodes, benefiting from commonalities in R&D with our EUV program, while ensuring the platform’s extendibility through System Node Enhancement Package upgrades. Thanks to these packages, any NXT system can be upgraded to the latest technology.
-
Product
Bottom-up and Top-down 3D Modular AOI
SpectorBOX
-
With up to 9 cameras per side (18 total), it is designed to inspect PCB’s inside solder frames from the heavy duty conveyor system suitable for assemblies up to 5kg. Inspection of PCBs without solder frames is also possible. The PowerSpector 550BTL handles PCBs with a maximum dimension of up to 550x550mm (21.6”). The PowerSpector 350BTL is designed for medium Size PCB’s up to 350x250mm (13.8″x9.8″).
-
Product
Drop Weight Tear Tester
DWTT
-
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
Product
Ultra-High Performance FLASH and DRAM Memories Test Solution
Magnum V
-
Teradyne’s Magnum V systems delivers high throughput and high parallel test efficiency for ultra-high performance FLASH and DRAM memories. Magnum V’s largest configuration delivers up to 20,480 digital channels at 1600Mbps per channel.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
Counter Input Module
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 1.81kΩ
40-251-022
Programmable Resistor Module
The 40-251-022 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
T3DSO1000/1000A Series Oscilloscopes
T3DSO1000/1000A Series
Oscilloscope
Teledyne Test Tools new T3DSO1000/1000A Oscilloscopes feature two channel and four channel models. The two channel model is available in 100 MHz, 200 MHz or 350 MHz bandwidths, a single ADC with up to 2 GSa/s maximum sample rate, and up to 28 Mpts of sample memory. The four channel scope is available in 100 and 200 MHz models and incorporates two 1 GSa/s ADCs and two 14 Mpts memory modules. When all channels are enabled, each channel has sample rate of 500 MSa/s and a standard record length of 7 Mpts. When only a single channel per ADC is active, the maximum sample rate is 1 GSa/s and the maximum record length is 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
Product
Multi-Wafer Test & Burn-in System
FOX-XP
-
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
Product
16-Channel VME Multi-Range Digitizer
V490
-
The V490 includes 16 independent acquisition channels, each with a programmable-gain differential amplifier, analog anti-aliasing filter, 16-bit analog-to-digital converter, and digital post-processing. With a dedicated A/D converter per channel, the V490 provides true simultaneous sampling, which can be extended across multiple V490s or triggered from an external TTL signal.
-
Product
Cleveland Open Cup Flash Point Tester
SYD'
-
Chongqing Lushun Scientific & Technological Development Co., Ltd.
The instrument is designed and made as per the National Standard of People's Republic of China GB/T3536-2008 "Test Methods for Flash Point and Fire Point of Petroleum Products (Cleveland Open Cup Method)". It is suitable to determine flash point and fire point of petroleum products and asphalt, excepting fuel oils and petroleum products having open cup flash point lower than 79 C.
-
Product
IQ Modulator
IQM Series
-
*Capable of receiving from DC to 500 MHz, LO inputs, outputting RF frequencies *Internal low noise oscillator *Internal reference *Buffered modulator Balanced IQ *Optimized for low EVM *Internal Reference Detect Switch Optional (EM Research RDS Series) *Up to 250 mega-symbols per second
-
Product
Voltage Input Device For FieldDAQ
-
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-026
Programmable Resistor Module
The 40-254-026 (PXI) and 42-254-026 (PXIe) are programmable resistor modules with 1 channel which can be set between 1.5Ω and 26.7kΩ with 8Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Data Loggers
-
Premier Electrosystems has a wide range of data loggers to suit your needs. All our data loggers can be customized as per requirement. Data loggers are electronic devices which automatically monitor and record environmental parameters over time, allowing conditions to be measured, documented, analysed and validated. The data logger contains a sensor to receive the information and a computer chip to store it. Then the information stored in the data logger is transferred to a computer for analysis.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 472Ω
40-251-020
Programmable Resistor Module
The 40-251-020 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Low Power FPGA Featuring Hardened MIPI D-PHY, LVDS, SLVS, SubLVDS, & Open LDI Bridging
CrossLink
-
*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per PHY*15 programmable source synchronous I/O pairs for camera and display interfacing*Available in amazingly small 2.46 mm x 2.46 mm WLCSP packages and BGA packages with 0.4 mm, 0.5 mm and 0.65 mm pitch
