Audio Signal Generators
-
Product
RF and Microwave USB Programmable Signal Generators
LSG Series
-
The Lab Brick LSG series of low cost USB-compatible RF and microwave signal generators covers frequencies from 20 MHz to 6 GHz with high output levels and excellent spectral purity. They require no additional DC supply voltage and offer several operating modes, including continuous-wave (CW) and swept-frequency. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
Product
PAL Standard Pattern Generator
PG315P
-
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
Product
Phase Splitter Comb Generator
-
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
Product
Arbitrary Waveform Generator
-
Berkeley Nucleonics Corporation
Is a piece of electronic test equipment used to generate electrical waveforms.
-
Product
Timing Signal Generator
OSA 5548C TSG
-
Our OSA 5548C Timing Signal Generator (TSG) is a scalable synchronization solution ranging anywhere from 20 unprotected outputs up to a thousand protected outputs by adding up to four expansion shelves to the core unit. Its ultra-compact footprint makes it ideal for telecom operators to provide scalable network synchronization in over-crowded exchanges. The OSA 5548C TSG’s distributed intelligence message passing system eliminates single points of failure and guarantees reliable uptime. Core unit and expansion shelves share the same modules, minimizing overall administrative complexity and enabling reduced homologation activity.
-
Product
Digital Signal Processor
HSR40 CC
-
Curtiss-Wright Defense Solutions
Curtiss-Wright’s CHAMP-XD2 digital signal processor (DSP) card handles the incoming data and features two multi-core Xeon D processors and two built-in 40 GbE interfaces. The processor hosts a Linux operating system and runs the HSR40 data recording and storing application. The processors can easily absorb the incoming data and redirect it to the persistent storage media, using 3rd generation PCI Express (PCIe), enabling the efficient movement of all the data.
-
Product
LAN Check With Tone Generator
PH-01
-
The LANCHECK consists of two modular units, a tester and a remote terminator. The modular design enables the tester to be used for local loop-back testing of patch cable or remote testing of pre-installed premise wiring. The LANCHECK makes it easy to recognize opens and shorts within a cable as well as identify reversed and miswired cables. It can verify a cable up to 2,000 feet in length. Furthermore, it comes with shielded connectors, which enables the testing of shielded twisted pair (STP) cables. It also features convenient Auto Scanning and precision Manual Scanning modes.
-
Product
Signal Analysis
Histograph
-
The Histograph software is used for statistical signal analysis: finding the statistical values characterizing the signal and building the theoretic histograms based on the data obtained.
-
Product
Impulse Test Generator
SUG-CCITT-A
-
Impulse Test Generator SUG-CCITT-A (1a. 10/700us, 6KV, figure is according to N.1 in IEC60950-1:2005 Annex N). N.1 ITU-T impulse test generators.
-
Product
Function Generators
-
Scientific Mes-Technik Private Ltd
Scientific offer wide range of function generators from 3 MHz to 10 MHz in general purpose and multifunction. Selection of waveform shapes apart from standard sine, triangle , square to ramp, pulse are available. SM5071 , SM5074 , SM5061 & SM5075 have built-in auto ranging frequency counter. The outputs are protected against short circuits and overload.
-
Product
Signal Conditioning System
SCS-801
-
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.The SCS-800 takes advantage of the increasing capabilities of notebook and desktop PCs by leveraging off the PC's strengths. It provides a high-performance, flexible solution whether used as a conditioning front-end for desktop systems in the factory or as a mobile solution for portable systems in the field.
-
Product
Signal Analysis
STA/LTA Detector
-
The STA/LTA Detector program is a representation of a detector of various events in triaxial or single-component time signals. The software is based on one of the STA/LTA detector types.
-
Product
Surge and Test Generator
STG 600
-
Cable fault location with the BAUR STG 600. The STG 600 surge and test generator is a multifunctional cable fault locator for low voltage networks. The surge and test generator is used for cable testing as well as for precise location of high-resistive and intermittent faults in low voltage cables.* Specifically for use in low-voltage networks* High surge energy: 600 or 1000 J** Light, compact and transportable* Single systems for cable testing and faults location
-
Product
16-Channel RTD Signal Conditioning Card
ProDAQ 5821
-
The ProDAQ 5821 series of Signal Conditioning Cards is designed to interface with a variety of sensors, principally RTDs, Thermistors, Cryogenic Diodes and Voltage type sensors. Each version of the 5821 provides the capability of precise 4-wire measurement. In order to achieve this, a precise 500μA constant current source is provided per channel. The current source can be disabled on a per channel basis and is monitored to ensure that current is flowing. The value of the output current is stored on-board after calibration. In order to achieve the highest accuracy the output current may be automatically calibrated 'on-the-fly' using the ProDAQ 3416 24-bit Sigma-Delta ADC card and an on-board precision resistor.
-
Product
Optical Delay Generator
-
The FR-203 provides periodic linear optical delay (~200ps) for ultrashort laser pulses. It is useful for applications such as time resolved spectroscopy and time domain terahertz spectroscopy. A well defined optical delay is generated with interferometric precision.
-
Product
Signal Generators/Calibrators
-
DC Voltage and Current Signal Generator and Tester for Routine Maintenance of Standard Devices
-
Product
Audio Cable Testers
AudioJog Pro 3
-
Audio cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection .
-
Product
Signal Analyzers (Spectrum Analyzers)
X-Series
-
Design, test, and deliver your next breakthrough signal analyzer (spectrum analyzer) with our most advanced signal analysis (spectrum analysis) tools
-
Product
Channel Load Generator
802.11p
-
Qosmotec Software Solutions GmbH
When many cars are equipped with 802.11p communication technology, high traffic density will also cause significant load on the radio channel. From normal wireless communication systems it is a known problem, that many users can cause a complete breakdown of the network. Car-to-X communication technology tries to protect itself against those kind of breakdown by a carrier sensing mechanism: Each communication device has to check first, if the radio channel is busy. In that case, it waits for a random delay to avoid packet collision on the radio channel, which causes a loss of both collided packets.
-
Product
Signal Processor Board
MS 1532
-
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
Product
CSI & DSI Protocol Generator
Envision X84 CSI&DSI
-
With comprehensive support for MIPI CSI-2v2 and DSI-2 specifications, Teledyne LeCroy’s Envision X84 generator platform provides the industry’s most accurate and reliable generation of MIPI camera and display protocols for fast debug, analysis and problem solving. The Envision X84 exerciser is loaded with innovative features that help uncover elusive protocol errors and is the intelligent choice for any camera and display validation needs. Using the same hardware platform as the Envision X84 C/D-PHY protocol analyzer, the Envision X84 offers the most flexible solution for MIPI Camera and Display validation and debug.
-
Product
Offline Signal Processing & Analysis Software
Signal Processing - DX
-
APEX Turbine Testing Technologies
DX is an easy to use, graphical, signal processing environment that simplifies analysis and reporting of dynamic data. DX includes everything needed to process data for a variety of applications and industries in a very intuitive, drag-and-drop user interface. Generate fully-interactive engineering plots from one or more tests and create reports in just a few mouse clicks.
-
Product
Alternate 2.64 (75.00) - 6.50 (184.00) General Purpose Probe
EPA-2X-1
General Purpose Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Product
Static Generation
Charging Electrodes
-
Fraser Anti-Static Techniques Ltd
Provide a safe, controllable, reliable and cost-effective method of applying static charge for temporary adhesion.
-
Product
Signal Conditioning
-
Mantracourt’s analogue output strain gauge signal conditioning modules offers a flexible solution for any analogue requirement.
-
Product
Signal Level Meter
0870S-5870S
-
Hangzhou Softel Optic Co., Ltd.
SLM-5870S operating range: 05 to 870MHz, work with Return path signal generator, it will measure the return path.
-
Product
Signal & Power PCB Connector
HPW Series
-
Smiths Interconnect's HPW series is a versatile interconnect with mixed signal and power contacts, up to 15A each
-
Product
Pulse Pattern Generators
-
The Pulse Master is a Series of Single and Dual Channel Pulse/Waveform Generators that offers a complete array of pulse, standard, arbitrary, sequenced and modulated waveforms with unmatched performance, even compared to instruments designed to generate fewer types of signals.
-
Product
Signal Analysis
Modal Analysis
-
Modal Analysis is used for analyzing pulse and transition characteristics of signals coming from the input channels of FFT spectrum analyzers and seismic stations in real time or recorded time realization view mode.
