Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
product
Multi-protocol USB Type-C Analyzer
Type-C Tracker
Protocol and Electrical Analysis Tool for Type-C Communications Standards. All-in-One: Concurrent and tightly synchronized capture of USB Power Delivery protocol, Type-C voltage tracking (Vconn, Vbus, SBU, and CC), USB 2.0, Thunderbolt 3 UART and DisplayPort auxiliary (AUX) signaling over the Type-C SBU lines, alternate (ALT) mode support for DisplayPort, HDMI, and Thunderbolt, and capture and decoding of Serial Wire Debug (SWD) protocol, UART, Serial Peripheral Interface (SPI) I2C vendor-specific protocols, and Type-C Port Controller Interface traffic over I2C.
-
product
Interface
RQVME2-1553
The RQVME2-1553 provides new levels of performance and flexibility for MIL-STD-1553A and B Notice II on the VMEbus. Available in commercial, industrial and conductively cooled versions with one, two or four dual-redundant channels, the RQVME2-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
-
product
EVISION Obstacle Detector
MS 1528
Obstacle Detector is a distance-measuring system based on ultrasonic sound utilizing the LPC2364FBD100. The system transmits a burst of ultrasonic sound waves towards the subject and then receives the corresponding echo. The LPC2364FBD100 integrated analog comparator is used to detect the arrival of the echo to the system. The time taken for the ultrasonic burst to travel the distance from the system to the subject and back to the system is accurately measured by the LPC2364FBD100. Assuming the ...show more -
product
PCIe VU13P UltraScale+TM With Massive Optical I/O
PCI597
The PCI597 is based on the Xilinx VU13P UltraScale+TM FPGA, which provides over 12,000 DSP slices, 360 Mb of UltraRAM and 3,780K logic cells. The Unit provides active cooling of the FPGA making it appropriate for power-hungry applications or those requiring temperature stability for good performance. The FPGA has interface to DDR4 memory channels (single bank of 64-bit wide, 16 GB). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
product
Cable Assembly, 160-Pin DIN41612, Male to Male, 1m
40-970-160-1m-MM
The cable assembly is not suitable for direct connection to Pickering Interfaces switching products.
-
product
SOP Managemen and Quality Management
arivis BM-Windream
BM-windream is the 21 CFR Part 11 compliant data and document management system for the pharmaceutical industry. It is based on the market leading windream document management system from windream GmbH, Bochum. In addition to our industry-specific modules, we have access to a series of tried and tested windream add-on modules from our partner network, e.g. for e-mail archiving, linking to ERP systems, CRM systems, knowledge management or scanning solutions. BM-windream provides a basis for your ...show more -
product
PXI General Purpose 2A Relay Module 19xDPST
40-132-202
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - XMC
Model 71141
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/Ds- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM...show more -
product
Rugged Blade Processor W/ Dual Xeon E5
ATC126
The ATC126 is a high performance ATCA processor blade featuring dual 14-core Intel® Xeon® processor (E5-2658 v4, E5-2680 v4, E5-2648L, 2618L, 2620 or 2630 v4), with up to eight banks of 256 GB DDR4 memory with ECC. Versatile connectivity includes two 10/40GbE Fabric Interfaces, dual GbE Base Interfaces, dual front panel GbE egress Ports, front panel dual RS-232 and USB 3.0/2.0 Ports and front panel DVI-I connector.
-
product
PXI Ethernet Interface Module
The PXI Ethernet Interface Module equips PXI systems with high-bandwidth Ethernet-based connectivity with up to 40 Gb/s data rates per port. Featuring compatibility with industry-standard network and automatic cable polarity detection, this module is ideal for high-performance data transfer and vision applications on the PXI platform. Additionally, the PXI Ethernet Interface Module has independent bandwidth to support up to four GigE Vision cameras without PoE.
-
product
PNA-X Microwave Network Analyzer
N5247B
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
2-Ch 1 GHz A/D and D/A with Virtex-7 FPGA - 6U VPX
Model 58730
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1 GHz 12-bit A/D- One or two 1 GHz 16-bit D/A- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
NI-9881, 1-Port C Series CANopen Interface Module
781673-01
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
product
75 Ohm MCX to MCX Cable Assembly
40-977-761-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
75 Ohm Mini SMB to 1.0/2.3 Adaptor Assembly
40-978-731-0.25m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Remote Particle Sensors
3718-A And 3719-A
Kanomax Remote Particle Sensors with analog output are designed to fit into your existing monitoring system, or they can be used as a stand-alone unit to monitor a critical area when connected to an alarm or controller. With two models available, these 2-channel remote particle sensors are capable of Modbus communication via RS485 interface. 0.1 cfm and 1.0 cfm flow rate models are available, along with flexible 4-20mA analog output with the 1.0 cfm unit (only).
-
product
Octal Small Form Factor Pluggable Electrical Interface
Eoptolink Technology Inc., Ltd.
Eoptolink is developing OSFP(Octal Small Form Factor Pluggable) a new pluggable form factor with eight high speed electrical lanes that will initially support 400 Gbps (8x50G or 4x100G). It is slightly wider and deeper than the QSFP but it still supports 32 OSFP ports per 1U front panel, enabling 12.8 Tbps per 1U switch lot. OSFP is designed to support the next generation of 800G optics modules that will use eight lanes of 100Gbps, and offers backwards compatibility with 100G QSFP.
-
product
Rugged 3U VPX Intel® Xeon® and 9th Gen Core™ i3 Processor Blade
VPX3020
- Intel® Xeon® Processor E-2254MLand 9th Gen Intel® Core™ i3 (formerly “Coffee Lake-H Refresh”)- DDR4-2666 soldered ECC SDRAM up to 16GB- Optional SATA SLC SSD, up to 64GB- Up to PCIe x16 Gen3 interface supporting non-transparent bridge=
-
product
Quad IP Carrier Module With Rear I/O
DP-cPCI-5121
DP-cPCI-5121 IP carrier board provides an electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.
-
product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 57891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex...show more -
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 2m HV, Exit Away From Pin 1
A050DM4-T-HA200
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Datalogging Light Meter (RS-232)
DLM 536
Spectrum of photo sensor meets C.I.E. photopic curve V(l). 16000 Records Data logging capacity. RS-232 interface (software included). Measurement of luminous intensity(PC Software)
-
product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial III
The PMC BiSerial family has been updated to include a Spartan III [Xilinx] based card with expanded capabilities.. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-III. The BiSerial III features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
product
PNA-X Microwave Network Analyzer, 43.5 GHz
N5244B
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Digital Interface
DNTBOB-88
BOB 88 is a high quality, general purpose interface to transmit and receive line level analog audio signals via a Dante network. Analog inputs are converted to digital and appear on the network as transmit channels. Audio for the analog outputs is taken from subscriptions to transmit channels on the network from other sources. When connected to a network, each break out box will appear as a separate device in the Dante Controller software interface.
-
product
Amplitude Detectors with Isolators
Full band waveguide detectors are GaAs beam lead Schottky diode-based detectors that are specially designed for millimeterwave network analyzer applications. With a proprietary circuitry design and careful diode selection, these zero-biased detectors exhibit high sensitivity and extremely flat output characteristics. The below standard offering covers the frequency range of 18 to 170 GHz and offers a 1 MHz video bandwidth and 1 MΩ video output impedance. The standard models also have the capacit...show more -
product
ARM LPC2294 Based Board
MS 2500
- JTAG interface- Boot Flash interface- External Flash interface for data storage- External Bus interface- SPI Interface- I2C interface- Serial port interface- CAN Interface- LPC2694 based processor board- MIL1553B Bus Interface (Dual Redundancy)
-
product
Microwave Converters
Each converter is designed with a broad palette of options available to the user at the time of order, to ensure that our solution matches the requirement as closely as possible:Choose the microwave and millimeter ranges.Specify an IF that supports adjacent or downstream equipment.Select from a range of data interfaces, reference stabilities, packaging forms, and environmental extremes.Customize, if needed, to meet the exact requirements of an application.
-
product
Thermometer Hygrometer Data Logger
S3120
Data logger is designed for record of temperature and humidity. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper communication adapter.
