Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Male, 0.5m
40-971B-200D-0.5m-MM
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
product
19’’ Rackmount 1/10 Gigabit Ethernet Switch
IC-SR-BOXa
The IC-SR-BOXa is based on the Interface Concept ComEth4000e Layer 2/3 1/10 Gigabit Ethernet switch into a 19’’ rack mountable box. The IC-SR-BOXa is dedicated to industrial and military networking applications.
-
product
40 GbE Network Attached Storage
HSR40 AC
Curtiss-Wright Defense Solutions
Handling the incoming data is Curtiss-Wright’s CHAMP-XD2, featuring dual Xeon D processors and two built in 40 GbE interfaces. The processors can easily absorb the incoming data and redirect it to the persistent storage media, using 3rd generation PCI Express (PCIe), enabling the efficient movement of all the data. By keeping the data as PCIe, instead of converting it to SATA and sending it to a SATA storage, the data can be directly pipelined over the backplane to the PCIe-based Non-Volatile Memory Express (NVMe) SSDs.
-
product
SIMRC - 8 x 2 Matrix 2-Pole
1030-R-8-2-2-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
NI-6583, 200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO
781320-01
200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO—The NI-6583 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 32 single-ended and 16 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6583 can sample digital waveforms at up to 200 MHz. It includes support for selectable single-ended voltages from 1.2 to 3.3 Volts with 10 bit resolution and common LVDS voltages.
-
product
Flexible x4 PCI Express to 4 MiniPCI Express Splitter
SKU-072-0X
Flexible x4 PCI Express to 4 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows connecting up-to four MiniPCI Express add-in expansion boards to the standard motherboard PCI Express connector.Splitter includes 4 MiniPCI Express Adapter boards, x4 PCI Express Host board and 4 Flat PCI Express Cables.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 7-Bank 40GHz SMA-2.9
60-801-407
The 60-801-407 is a 6-channel, 7-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI High Density MUX BRIC, 32-Chan, 20-Pole
40-570-314
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXIe-6591, 12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument
783638-01
12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument—The PXIe‑6591 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex‑7 FPGA to implement various high-speed serial protocols, and it is programmable with the LabVIEW FPGA Module for maximum application-specific customization and reuse. The PXIe‑6591 takes advantage of FPGA multigigabit transceivers and up to eight TX and RX lanes. In addition to high-speed serial lanes, the PXIe‑6591 features digital I/O signals that support multiple logic families with per line, per cycle direction control.
-
product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
785192-01
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
product
44-Pin D-Type Male Connector
40-963-044-SM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
S-Type Load Cells
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
product
Calibration Lead Precision Resistor, Triple
40-975-009-SL3
The cable assembly is specifically designed to connect to the 9-Pin D-Type calibration port located on the front panel of Pickering Interfaces Module Part Numbers 40-260, 40-261, 40-262, 40-263 and 40-265.
-
product
Interface Technology ProLine
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation Amplifier for DC voltage and current measurement with galvanic isolation, active and passive standard signal isolation amplifier, supply isolation amplifier for supplying 2-wire sensors, transmitter for temperature and AC signals, isolating amplifiers for high voltages and shunt applications. T
-
product
200W Autoranging Power Supply, 60V, 10A
E36232A
E36232A provides more useable power with autoranging architecture in a bench friendly design with full programmability; LAN, USB and optional GPIB interface.
-
product
Platforms
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
-
product
Development System
PCIe490
The PCIe490 Expansion Chassis enables users to scale application workstations with up to eight additional PCIe boards per chassis and up to 63 total slots with chassis daisy chaining. It was designed to accommodate the Abaco Systems PC820 and PC821 with Xilinx Ultrascale technology and multiple FMC+ interfaces.
-
product
PXI High Density MUX BRIC, 40-Chan, 20-Pole
40-570-315
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Dual 3U CompactPCI® Subsystem with Two 6-slot Backplanes and Two CompactPCI® Power Modules
cPCIS-2642 Series
- Dual 3U CompactPCI® Systems, each with five peripheral card slots and one system slot- 1/1 250 W CompactPCI® Power supplies- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5 V, +3.3 V, and +12 V- PICMG® 2.11 47-pin power interface
-
product
KYK-13 Interface
IP-Crypto
The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.
-
product
SWIR Line-Scan USB3 Cameras
NECTA S Series
NECTA S, the SWIR line-scan model in NECTA camera family, is capable of high-resolution acquisition in short-wave infrared bandwidth, ranging from 950 to 1700 nm. This new SWIR camera can reach up to 40kHz line rate with 14bit A/D converter: its high-speed USB3 interface, an advanced I/O, together with a compact and rugged aluminum case, make NECTA S suitable for most demanding machine vision applications.
-
product
Proximity, Light, RGB, and Gesture Sensor
APDS9960
Add basic gesture sensing, RGB color sensing, proximity sensing, or ambient light sensing to your project with the Adafruit APDS9960 Proximity, Light, RGB and Gesture Sensor. When connected to your microcontroller (running our library code) it can detect simple gestures (left to right, right to left, up to down, down to up are currently supported), return the amount of red, blue, green, and clear light, or return how close an object is to the front of the sensor. This device uses an I2C interface so it's easy to wire up and use.
-
product
Clock and Data Recovery/Retiming
Analog Devices provides single rate, multiple rate, and continuous tuning clock and data recovery (CDR) ICs for metro, long haul, DWDM, FSO, instrumentation, and other applications. Our any rate CDR ICs allow easy integration into protocol agnostic applications, automatically locking onto incoming data streams at any rate, from 10 Mbps to 2.7 Gbps or from 6.5 Mbps to 11.3 Gbps, without the aid of a reference clock while reporting the acquired data rate over the I2C interface. With a proprietary dual loop design, our any rate CDR ICs feature fast locking with superior jitter performance.
-
product
Digital Pressure Gauge
m1M
AMETEK Sensors, Test & Calibration
Affordably Accurate! Featuring a 3 year recommended calibration interval, DNV approval, and an easy-to-use, time-saving user interface.
-
product
Potentiometer for OEMs
FlexiPot
The best user interface, whether in consumer electronics or industrial controls, contains sensors that cause minimal interference, meaning the user may not even know they are there. FlexiPot, by Tekscan, is a flexible membrane potentiometer with an ultra-thin (0.008"), lightweight profile. Low power requirements combined with a linear output make it the ideal position sensor, from both a manufacturing perspective as well as a user perspective.
-
product
LAN⇔RS-422/RS-485 Converter (Insulated, Wall-hanging Model)
SI-65FA-L
SI-65FA-L is an interface converter to connect equipments such as equipment for factory automation or analyzers which have RS-422/485 communication ports to LAN.
-
product
CalPod Controller
85523B
The operation of the CalPods is via VNA firmware, and the CalPod controller provides the control signals for operation of the CalPod calibration refresh modules. The CalPod controller interfaces with the PNA family and M937xA PXIe vector network analyzers.
-
product
Circuit Module, Riser for ISMB, PCIex4 to 3 PCI A201,RoHS
AIMB-R430P-03A2E
- Connecting Interface: PCIe x4- Expansion Slots: 3 x 32-bit/33 MHz PCI- PLX PEX_8111BB PCIe to PCI Bridge
-
product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
product
PXI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module
778967-01
64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PXI‑6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
