Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
Test And Simulation Devices
BreakingPoint
-
Control global threat intelligence at Internet-scale to create massive-scale, high fidelity simulation and testing conditions for battle-testing infrastructures, devices, applications, and people.
-
Product
High Speed DC Electronic Load
6330A series
-
The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.
-
Product
RF Waveguide Load
-
RF Lambda’s waveguide loads are used at end of an RF signal chain to provide a good 50ohm match and dissipate any RF energy into heat. They are available in a variety of power levels and offer low VSWR.
-
Product
Resistor Simulator Card
CP-RESSIM-16
-
The CP-RESSIM-16 Resistor Simulator PCIe Card provides programmable resistance simulation across multiple channels for real-time test and validation environments. The card supports 16 independent digital programmable resistors, enabling accurate emulation of variable resistance conditions within a system.
-
Product
GNSS Testing & Simulation
-
Safran Federal Systems is a leading provider of advanced GNSS Testing & Simulation systems and tools for NAVWAR environments.
-
Product
Economical Load and Force Measurement
ELF
-
Tekscan's ELF force and load measurement system matches the market's need for an inexpensive load and force measurement system with Tekscan's ability to deliver innovative load and force measurement solutions. The system consists of data acquisition hardware, software, and FlexiForce B201 sensors.
-
Product
Acrylic Microbial Fuel Cell With Ion Exchange Membrane
MFC-1
-
MFC-1 Acrylic Microbial Fuel Cell with Ion Exchange Membrane is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation or customized electrochemical workflows depending on the model. Choose the cell volume, window material, sealing method and port configuration according to electrode size, electrolyte compatibility, gas control and characterization method. For custom experiments, confirm electrode spacing, membrane requirements and temperature control before ordering.
-
Product
Load tester for JA and C Type Durometers
-
It is necessary to check the shape and height of the indentor, the indicating mechanism, and other parts of the hardness tester are set correctly before doing a load test.
-
Product
3D Electromagnetic Simulation Software
XFdtd®
-
A full-featured simulation solver, XFdtd outpaces other methods in efficiency as the number of unknowns increases. XF includes full-wave, static, bio-thermal, optimization, and circuit solvers to tackle a wide variety of applications, including antenna design and placement, biomedical and SAR, EMI/EMC, microwave devices, radar and scattering, automotive radar, and more. It also works with Remcom's ray-tracing products to provide thorough simulation capability at the low-, middle-, and high-end of the electromagnetic spectrum.
-
Product
Electromagnetic Environment Simulators
A2PATS® Products
-
Our A2PATS Family of Products are electromagnetic environment simulators built upon Textron Systems' open-architecture direct digital synthesizer technology, coupled with our proven user interface. Our easily programmable, plug-and-play modular architecture uses identical, phase-coherent, direct digital Synthetic Stimulus Instruments (SSIs) as the radio frequency (RF) source for all signals. These modular commercial RF Sources are easily configured in our commercial cabinets. Four standard configurations are available including single-cabinet, multi-cabinet, mini-A2PATS, and A2DSG™.The A2PATS Family consists of numerous commercial products including but not limited to A2PATS, A2DRI™, A2DSG and A2EOSTIM.
-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
Programmable DC Electronic Load
IT8500+ Series
-
IT8500+series (150W~3000W) single-channel programmable DC electronic loads are designed for middle & high-end applications. They can be offered as multiple solutions according to customer's design and testing requirements.
-
Product
AC Load Banks
X100L Series
-
Mosebach Manufacturing Company
Introducing Mosebach’s X100L load bank. One of the lightest dual voltage, 100 kW load banks on the market! The unit weighs approximately 64 lbs. and has 5 kW resolution. The X100L load bank includes an Industrial strength, injection molded, 100% water proof case with wheels as shown below.
-
Product
High Output Simulators
-
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house – no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
Product
Battery Cell Formation System
17000 series
System
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
Programmable DC Electronic Loads (conventional and regenerative)
-
Elektro-Automatik GmbH & Co.KG
Our programmable electronic loads are composed of an optimum mix of analogue- and digital technology (µ-controller/FPGA based). By combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of electronic-load series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D. EA programmable electronic loads are available in conventional technology (heat dissipating) and as “regenerative” loads. The latter allows, specifically under long-term testing condition (e.g. battery discharging) a full amortisation of its invested value by its energy-saving capability, similar as with Photovoltaic installations.
-
Product
Simulation And Training
-
With more than 25 years of experience, Textron Systems Simulation and Training provides comprehensive end-to-end training solutions for air, land, sea, space, unmanned and electronic warfare platforms. We design, develop, and support integrated training devices, classroom courseware, virtual, live and constructive training, and software solutions. Our products and services support advanced platforms including C-17 Globemaster®, B-1 Lancer, F-35 Lightning II®, F-22 Raptor® and other high-value assets. Textron Systems also produces electronic, RF, and/or multispectral test equipment for verification and validation of these and various other air, land, sea, space, unmanned and electronic warfare platforms.
-
Product
Test & Simulation Interface for PCI-X
PCI-X-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI-X
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBO SERIES
-
The LBO Series (Load Button) load cells are offered for compression only applications where space is limited. Matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4phstainless steel and sealed for use in mostindustrial environments.
-
Product
Telephone Line / Load Analyzer
TLLA-2500 Pro
-
Detects and Alerts the user of almost ANY Telephone Wiretap (Tap), even from the Telephone Central Exchange (REMOBS), with the added ability of defeating common types of wiretaps.
-
Product
Waveform Generation Toolbox for Wideband Signal Simulation
N7509A
-
The Waveform Generation Tool provides a simplified interface for baseband modulation of Keysight's wide bandwidth signal simulation solutions, for signals with up to 1 GHz RF bandwidth. Even the most complex signals are defined and implemented easily through the software interface. Signals can be defined through basic parameter entry or from files created in MATLAB or other engineering environments. For each selection in the main menu, a subsequent screen appears, enabling the user to enter the parameters required to define the waveform and invoke the built-in calibration routines. A display on each sub-panel shows the ideal frequency domain waveform calculated from entered parameters. A simulation mode is provided to enable development and operation without connection to the instrument hardware.
-
Product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
-
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
Product
Load Termination
-
A process of ending a transmission line or cable to either dissipate energy as heat or prepare it for connection to a device.
-
Product
Perforated Positive Coin Cell Case For In-Situ Testing
PCC1
-
Perforated CR2032 stainless steel coin cell case (4-piece set) with customizable hole diameters for in-situ electrochemical testing, gas diffusion studies, and battery material research.
-
Product
Swagelok-Type Three-Electrode Battery Test Cell
STB1
-
A Swagelok-type three-electrode electrochemical test cell designed for battery research, electrochemical analysis, catalyst evaluation, and laboratory material testing.
-
Product
Load Banks
-
Power Test Dynamometer offers a complete high capacity load testing solution with our load bank and gen set testing systems. Capable of testing generators and AC/DC power sources, our load bank systems safely apply electrical loads across the entire spectrum of operation. By offering a one-stop-shop for your Load Bank and it's accompanying data acquisition software, Power Test is committed to Making Your Testing Easy.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Multiple Cell Battery Chargers
-
Renesas' highly versatile battery charger ICs support devices with rechargeable 2, 3 or 4-cell batteries and include configurations such as a hybrid power boost (HPB), narrow output voltage DC (NVDC), buck-boost NVDC, and SMBus Level 2.
-
Product
Dc Load Bank
-
Highly reliable and durable new alloy resistor is used for the JUNXY DC load bank. It is thermal shrinkable and seal installed in the stainless steel pipe, whose surface with insulated heat sink. The resistor is moisture-proof, anti-corrosion, good heat dissipation, high insulation resistance, safe and reliable.
