Automotive
Car industry or about cars.
See Also: Vehicle, V2X, Truck, Electric Vehicle, Car, Autonomous Vehicle, Autonomous Underwater Vehicle
-
Product
PCI-6110, 4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777475-01
Multifunction I/O
4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6110 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6110 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6110 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
High Voltage Battery Test System
-
The increasing use of electric drive systems both in the automotive industry and in transportation requires the development of new high-performance energy storage systems. In order to support you in the development and production of these systems, S.E.A. develops individually configurable test systems which are scalable and can be used flexibly for the respective requirements.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 1 kV Isolation
43-752A-113
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Graphene Sensors & Imagers
-
Passive and active imaging solutions in low-light conditions, e.g. in automotive, aviation, security, search-and-rescue and surveillance applications. Spectroscopy & machine vision detector technologies for material, composition and structural analysis, e.g. for agriculture, food industry, pharmacy and waste sorting applications & CMOS manufacturing quality control.
-
Product
POWER PROBE 4
PP401
-
*Electronic circuit and component tester that supplies battery ground and power along with 8 diagnostic testing modes to provide automotive technicians with detailed information on the circuits and signals being tested*Diagnostic Modes include: AC/DC Voltmeter, Ohmmeter, Frequency, Pulse width (Positive and Negative) Fuel Injector Tester, PCM/ECM Driver Tester and PPECT3000 Signal tracer*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)
-
Product
Custom & ASSP
-
Offering innovative SoC, SiP, ASIC, audio/video ASSP and other custom solutions and foundry services across a wide variety of applications in the automotive, industrial, medical, and aerospace & defense markets.
-
Product
3-Pin B2CF Omnimate Male to Pigtail, Unshielded Automotive Ethernet Cable
787108-05
Ethernet Cable
Cable, 3POS B2CF Omnimate To Pigtail, Automotive Ethernet, Unshielded, 5m
-
Product
Sensor Tester
QST-5
-
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
Product
Specialty Lab Testing Services
-
Serving the Testing and Consulting needs for the Aerospace, Automotive, Bio-Medical, Military, Electrical and Electronics Product Industries since 1995 with technical excellence and exemplary customer service. Failure Analysis, Electronics Qualification, Screening, Environmental Test, Shock, Vibration, Package Test, and Transportation Simulation. Our customers come from a diverse group of manufacturers, from start-ups to Fortune 500 companies.
-
Product
Portable Ruggedized Test System
BADGER
-
Badger systems utilize NI's CompactRIO (cRIO), Single Board RIO (sbRIO), and/or CompactDAQ (cDAQ) hardware. The Badger product line offers high speed data acquisition/control and flexibility in an industrial package. Badger chassis and instrumentation have a 50 g shock ratings and a wide -40 to 70 °C operating temperature. These systems are ideal for automotive, industrial automation, remote monitoring, field service, and advanced control applications.
-
Product
IP and NEMA Ingress Testing
-
Environment Associates offers dust, water and solid ingress protection testing to multiple specifications including EN/IEC 60529 and NEMA 250 for electronics enclosures, SAE standards for automotive components, RTCA DO-160 for commercial aircraft and various MIL standards for associated military hardware.
-
Product
Resistors and Inductors
-
Panasonic Automotive & Industrial Systems Europe GmbH
Our wide line-up of various Resistor and Inductor technologies supports the needs of the major industries such as Automotive, Industry, Telecom, HA and Medical markets. SMD, THT and axial shapes are available to support engineer's requirements.
-
Product
Load Cells
-
We make it our business to stay on top of emerging industry demands so that the load cells we provide help you meet your ever-changing test requirements. Our broad selection of competitively priced load products will help you meet the most demanding test and measurement requirements. Used in automotive, aerospace and defense, R&D, and process control applications, our drop-in replacement load cells are designed to provide years of dependable performance.
-
Product
Automotive Oxygen Sensor
Model R-22A
-
Teledyne Analytical Instruments
Teledyne has a long and successful history in the development and supply of oxygen sensors for automotive emission testing equipment.The “R” series sensors are used by most automotive emission equipment manufacturers worldwide. We are striving to improve our sensors through aggressive research and development, assuring the highest quality products offered by any supplier of oxygen analyzers.
-
Product
Automotive Cybersecurity
-
On the one hand, connectivity functions allow manufacturers to monitor the vehicles’ state and install security updates when necessary. On the other hand, the growing number of communication channels increases the potential of gateways for hackers. To create a secure vehicle, you must consider all the connected elements and take a holistic approach.
-
Product
RH850 Family (Automotive only)
RH850/F1x
-
The RH850/F1x series microcontrollers are successor of V850E2/Fx4 and V850E2/Fx4-L. It expands on-chip flash memory and adds a small 48-pin package.
-
Product
SparkFun GNSS-RTK Dead Reckoning Breakout
ZED-F9K (Qwiic)
-
The SparkFun ZED-F9K GNSS Breakout is a high precision, sensor fusion geospatial board with equally impressive configuration options and takes advantage of u-blox's Automotive Dead Reckoning (ADR) technology. The ZED-F9K module provides a highly accurate and continuous position by fusing a 3D IMU sensor, wheel ticks, a vehicle dynamics model, correction data, and GNSS measurements.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-193A-002
Switch Module
The 40-193A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Test Handlers
-
Cohu has 50+ years of semiconductor test expertise designing and manufacturing pick-and-place, gravity feed, test-in-strip handlers, MEMS test cells, and turret-based test handling and back-end finishing equipment for ICs, LEDs and discrete components.Our test handlers support a variety of package sizes and device types, including automotive, mobile, power, micro-electromechanical systems (MEMS) and microcontrollers, among others.
-
Product
Battery Testing Chambers
-
We supply a variety of test chambers for testing small battery cells to large lithium ion battery packs. Battery test chambers are supplied to a variety of industries including telecommunications, computer and automotive. With the goal of reducing automobile emissions and the development of electric vehicles, the need for lithium ion battery testing is even more critical. Our proven experience provides the most cost-effective solutions. Each test chamber is built according to specific test requirements and may be interfaced with battery cyclers, control & monitoring data acquisitions systems and other test equipment for a complete integrated test solution. All environmental chambers are designed with safety in mind. A variety of safety features are provided for reliability and abuse testing of batteries. These features may be incorporated into CSZ test chambers and tailored to the various hazard levels of EUCAR (European Council for Automotive R&D), a consortium of European car manufacturers. To better assess the hazard potential of tests, EUCAR has investigated hazardous situations and divided them into eight risk classes. The development of the safety equipment of our battery test systems is also based on this classification. For each hazard level, we recommend specific safety options that can be included with your chamber to meet your specifications to safety test your product. Together with our customers, we assess which safety devices are necessary for the respective test chambers.
-
Product
EMC Testing
-
D.L.S. Electronic Systems, Inc
EMC testing and consulting services to the Electronics, Medical Equipment, Automotive, Aerospace, Computer, Telecommunications, and other industries. We are a NVLAP certified test facility, capable of testing electronic equipment to today's high frequency requirements. Our 14 Test chambers and 3 Open Area Test Sites can perform full scan Immunity and Emission testing at frequencies up to 40 GHz. Please contact us for your specific requirements.
-
Product
PCI Digitizers
ATS850
-
ATS850 digitizers offer the lowest cost solution for data conversion in automated test applications and automotive R&D. With its low cost, high signal quality and robust analog front-end, ATS850 is ideal for OEM applications that are very cost-sensitive.
-
Product
High-Speed Lighting
-
Atlas Material Testing Solutions
Better pictures matter, especially in the automotive safety industry. No matter whether coming from Real-Crash or the Crash-Simulation stand - only high-quality pictures will allow researchers to get insights for superior product improvements.
-
Product
Easy and Non-Destructive Airflow Resistance Measurements of Materials and Parts
CARE+
-
The control of airflow resistance in the production of materials and components is a growing requirement in the automotive industry. CARE+ (Concentric Airflow Resistance Evaluator) is an apparatus designed to measure the airflow resistance of materials and parts. Measuring non-destructively, CARE+ is particularly applicable in the quality control of parts and materials.
-
Product
Cameras
Miro C and N
-
The Phantom Miro C and N series cameras are designed to fit into spaces that a standard camera can't reach. Lightweight bodies, on-board data protection, and rugged construction make them popular in automotive, microscopy, and destructive testing environments.
-
Product
PXI 32 Channel Switch Simulation Module
40-480-221
Digital I/O
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
PXI 8 Channel Switch Simulation Module
40-480-021
-
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Arduino CAN Shield
IFB-10003-ANP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
PORTABLE COORDINATE MEASURING MACHINE
CMM
-
The HandyPROBE arm-free probing system generates high-accuracy measurements (accuracy of up to 22 µm), and outperforms traditional portable CMMs on the shop floor. The HandyPROBE portable CMM is currently used on the production lines of major players from the automotive, aerospace and manufacturing industries.
