Solder Joint
-
Product
25-Pin D-Type Male Solder Bucket
92-960-025-M
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
Waveguide Rotary Joints
-
Waveguide Rotary Joints are used for the rotary transmission of power and signal between the stationary and rotating parts of a radar or satcom system.EVERAXIS has designed and produced single and multi channel Waveguide (WG) Rotary Joints since 1958. Every new design is simulated in FEM software as well as physically tested for optimal performance. Each high power Waveguide Rotary Joint is tested at maximum peak power before shipment.
-
Product
Replacement Solder Tip Lead Set for D410/D610
Dx10-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Selective Wave Soldering Optical Inspection Machine
-
Landrex Technologies Co., Ltd.
Selective Wave Soldering Optical Inspection Machine
-
Product
SparkFun Solder-able Breadboard
Mini
-
This is the Mini SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our mini modular breadboards with the same connections to pins. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
Product
50-Pin D-Type Male Solder without Backshell
92-960-050-M
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections. 50-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module.
-
Product
Solder Paste Printers
-
Shenzhen Leadsmt Technology Co.,Ltd
Is mainly used to print the solder paste to the circuit board, is one of the essential equipment in electronic manufacturing.
-
Product
Coax, Patchcord, ITA, 20", Mini Coax, Solder Sleeve, RG316 Tan, Single-Ended
7-339116000-036
Coax Patchcord
Mini Coax, ITA, Solder Sleeve (50 Ohm, 2 GHz) to RG316 Tan (50 Ohm, 3 GHz).
-
Product
Solder Paste Analysis
SPA1000
-
The SPA 1000 also introduces new process control capability by accurately measuring the suitability of the solder paste prior to its implementation on the production line. It achieves this by determining the "Open-Time" for the paste. It also performs the Slump Test and both of these methods provide a "Go/No Go" answer in less than 30 minutes to ensure minimum delay for the production line.
-
Product
160-Pin DIN41612 Connector, Solder Pin, Male
92-960-160-M
DIN41612 Male Connector
Suitable for users to create their own cable assemblies, this product can be supplied with or without the backshell. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the connector can be fitted with an optional screwlock assembly.
-
Product
Soldering Inspection Video Microscope
MS-1000
-
The MS-1000 is a highly portable microscope for exclusive use with BGA, CSP, and QFP. It is highly efficient in inspecting portions which cannot be inspected by the X-ray inspection method.Specifically, it is efficient for inspecting the following conditions: fillets of soldered balls, melted condition of soldered parts, cracks, defective soldering, etc.
-
Product
3D Solder Paste Inspection (SPI)
TR7007 SII
-
Offering inspection speeds of up to 200 cm2/sec, the TR7007 SII is the fastest solder paste inspection system in the industry. This highly accurate inline shadow-free solder paste inspection solution offers full 3D inspection at resolutions of 15 µm or 10 µm. Built on a high precision linear motor platform, the system's hallmark features include closed loop function, enhanced 2D imaging, auto-warp compensation and fringe pattern technology. Increase capacity without sacrificing additional space with an available dual-lane configuration.
-
Product
Dual Projection 3D In-Line Solder Inspection System
KY8030-2
-
The new KY8030-2 delivers 2x fasterinspection without compromising performanceand accuracy.Using patented dual projection, the systemeliminates the critical Shadow problem thatall 3D SPI systems can be vulnerable to.Easy UI and SPC Plus are included in the systempackage in order to help users achieve faster& easier printer process optimization
-
Product
20-Pin GMCT Male Connector, 10A, Panel Mount, Solder Bucket
40-963-020-10A-M
GMCT Male Connector
The 40-963-020-10A-M connector is designed to allow users to directly terminate a cable with soldered connections. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. Included is the screwlocks/fixing screws and male solder bucket contacts.
-
Product
3D Solder Paste Inspection system
PI Series
-
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
Product
Joint Services Electronic Combat Systems Tester
JSECST™
-
The Joint Services Electronic Combat Systems Tester (JSECST) is part of the family of testers, supporting the U.S. Air Force, Navy, Army, and over 23 allied nation platforms. JSECST performs full end-to-end diagnostic tests of installed systems including radar warning receivers (RWRs), jamming systems, communication systems, and navigation systems. Our JSECST delivers confidence for flight crews and the technicians who support them. It quickly and accurately tests and fault-isolates electronic combat and avionics systems for today's most advanced combat aircraft.
-
Product
68-Pin SCSI Micro-D Female Solder Bucket
40-962-068-SB-F
SCSI Female Connector
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
37-Pin D-Type Female Solder Pin HV
40-960-037-F-HV
D-Sub Female Connector
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
High-speed 3D Solder Inspection Machine
YSi-SP
-
a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.
-
Product
Wave Soldering Machines
-
Shenzhen Leadsmt Technology Co.,Ltd
A bulk soldering process used for the manufacturing of printed circuit boards.
-
Product
Solderability Tester
ZHX-35
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.14-2008Used to detect the self-solderability of enameled round wires and wire harness;Set variable temperature range and automatically maintain constant temperature;Under mechanical driven, samples would be withdrawn by the action of automatic insertion and lateral movement, free from vibration and noise;
-
Product
Connector, 104-Pin D-Type Female, Solder Bucket, 5A, 4-40 UNC Screwlocks
C104DFR-2SB-1A
D-Sub Female Connector
This 104-pin female D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell. This connector is suitable for use with Pickering modules that use the 104-pin D-type connector.
-
Product
RF Rotary Joints
-
EVERAXIS is the market leader and supplier of choice for integrated waveguide assemblies, passive microwave components, RF Rotary Joints and rotating subsystems to the military and commercial radar and satcom markets. Working together with customers to create tailor-made solutions optimized to meet their needs has been the EVERAXIS business model for more than 70 years.
-
Product
Replacement Solder Tip Leadset for Use with D420/620
Dx20-SI-HiTEMP
-
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Product
Fiber Optic Rotary Joints
-
Fiber Optic Rotary Joints ensure flawless high-speed data transmission even in environments with strong electromagnetic interference. They are a maintenance-free alternative that eliminates friction and/or heating between rotating and stationary components.
-
Product
SparkFun Solder-able Breadboard
-
This is the SparkFun Solderable Breadboard. A bare PCB that is the exact size as our regular breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector Without Backshell
C096SFX-XSP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Soldering Test
-
The soldering tests are conducted to determine if materials can withstand soldering effects, such as resistance to soldering heat, as well as the solderability of components during the manufacturing process.
