Solder Joint
-
Product
Solder Paste Printers
-
Shenzhen Leadsmt Technology Co.,Ltd
Is mainly used to print the solder paste to the circuit board, is one of the essential equipment in electronic manufacturing.
-
Product
Solder Wettability Tester
5200TN
-
Amid the rapid progress in miniaturization of electronic components in high-density mounting, a long-established company that has been manufacturing solder wettability testers for about 40 years has developed a solder wettability tester compatible with the latest micro electronic components. and is the top model in the history of solder checkers with improved operability. * Wetting stress is proportional to the circumference of
-
Product
50-Pin D-Type Male Solder without Backshell
92-960-050-M
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections. 50-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module.
-
Product
Replacement Solder Tip Leadset for Use with D410/D610
Dx10-SI-HiTEMP
-
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Product
3D Solder Paste Inspection system
PI Series
-
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
Product
68-Pin Micro-D Male Solder Bucket
40-962A-068-SB-M
SCSI Male Connector
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Single Mode Fiber Optic Rotary Joints
-
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
Product
Rotary Joint
-
RF Lambda’s rotary joints are available in a variety of channels and configurations allowing the connection of waveguides and allowing for rotation of the different sections.
-
Product
Standard DIP Socket with Solder Tail Bifurcated Contacts
Series 511
-
Standard DIP Sockets with Wire Wrap Bifurcated Contacts. Features: Standard DIP sockets are available with solder tail or wire wrap pins, all with bifurcated contacts. Consult Data Sheet No. 12005 for wire wrap pins. Aries offers these standard DIP sockets in more sizes than any other manufacturer.
-
Product
SparkFun Solder-able Breadboard
-
This is the SparkFun Solderable Breadboard. A bare PCB that is the exact size as our regular breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
Product
Mini Coax, Contact, ITA, RG316 & 178, Solder Sleeve
610103158
Coax Contact (ITA)
Contact, ITA, Mini Coaxial, RG316 & 178, 50 MAU, Solder Sleeve
-
Product
Solder Cup Connector Kit
Y1139A
D-Sub Female Connector
Used to build custom cables for 34921/23/25/31/32/33/37/38 –50-pin Dsub female – 125 V
-
Product
Solder Paste Inspection System
KY8030-3
-
The new KY8030-3 delivers 3x fasterinspection without compromisingperformance and accuracy.Using patented dual projection,the system eliminates the criticalShadow problem that all 3D SPI systemscan be vulnerable to.Additionally, the new KY8030-3 has solvedthe PCB Warp problem that seriouslyimpacts inspection accuracyand reliability of result.
-
Product
Soldering Test
-
The soldering tests are conducted to determine if materials can withstand soldering effects, such as resistance to soldering heat, as well as the solderability of components during the manufacturing process.
-
Product
High Speed Solder Paste Inspection
VisionPro HSi
-
The VisionPro HSi offers high speed solder paste inspection. Utilizing the most advanced high resolution staging and sensor technologies, the VisionPro HSi provides the accuracy and reliability needed to compliment your overall screen print process improvement strategy.
-
Product
Solderability Tester
LBT210
-
Microtronic Microelectronic Vertriebs GmbH
Microtronic's LBT-210 solderability tester has software that offers statistical information such as mean value, standard deviation, etc. A camera option offers video of the test cycle and storage in memory with the appropriate test measurements and data. Additionally, it has the feature to test under nitrogen. This function can be switched on in the software. An enclosure that is flooded with nitrogen lowers and rises with the device under test.
-
Product
37-Pin D-Type Male Solder Pin HV
40-960-037-MHV
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
25-Pin D-Type Male Solder Bucket
92-960-025-M
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
40-960-009-M-HV
D-Sub Male Connector
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - With Backshell
-
Product
Waveguide and Coaxial Rotary Joint Assembly
-
Waveguide and Coaxial Rotary Joints are used for the transmission of power and signal between the locked and rotating parts of a radar or satcom system.
-
Product
Coaxial Rotary Joints
-
EVERAXIS single and multi channel Rotary Joints are designed to work in rotating 50 Ohm systems, where uninterrupted and low loss signal transfer is required. Coaxial Rotary Joints are compact and lightweight compared to Waveguide Rotary Joints.
-
Product
GENERAL INSPECTION MACHINE AFTER SOLDER MASK
-
DVI is a technology of automated optical inspection, which can inspect deep to the difference from semi-transparent layers or semi-reflective layers.
-
Product
Solder Past Inspection
-
From the innovative Z-Check 3D through to the entry level Z-Check 100 the entire range has been designed to provide accurate pad specific measurement of solder paste deposits, adhesives and component placement. Amongst its other features the Z check software comes with the convenience of a full SPC package as standard.
-
Product
Solder Paste Inspection System
LaserVision SP3D Mini
-
The LaserVision SP3D Mini offers the same level of overall measurement capabilities as the VisionPro SP3D. Utilizing a lower cost microscope platform and the ability for customers to supply their own PC if needed, the SP3D Mini sets the "affordable" boundary on reliable, low cost SPI solutions.
-
Product
Open-Frame Collet Socket with Solder Tail Pins
Series 518
-
Open Frame Collet Sockets with Solder Tail Pins. Features: Open frame allows for more efficient utilization of board space and better cooling. Choose from several pin styles. Compatible with automatic insertion equipment. Side-to-side and end-to-end stackable.
-
Product
Replacement Solder Tip Lead Set for D410/D610
Dx10-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Solder Wettability Tester
5200ZC
-
The current machine (5200TN) was developed as a comprehensive machine that covers solderability test standards around the world, but we have added a high cost performance machine to the lineup that has realized the request of "single function + low price", which many people who are using the successive machines of SAT2000-5000-5100 type.
-
Product
Connector, 104-Pin D-Type Female, Solder Bucket, 5A, 4-40 UNC Screwlocks
C104DFR-2SB-1A
D-Sub Female Connector
This 104-pin female D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell. This connector is suitable for use with Pickering modules that use the 104-pin D-type connector.
-
Product
Pin-Line™ Collet Socket with Solder Tail Pins
Series 0513
-
Pin-Line Collet Sockets with Solder Tail Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with solder tail or wire wrap pins. Consult Data Sheet No. 12014 for wire wrap pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
SparkFun Solder-able Breadboard
-
This is the SparkFun Solderable Breadboard. A bare PCB that is the exact size as our regular breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
