Showing results: 166 - 180 of 381 items found.
-
-
-
HD52.3D… Series -
Delta OHM S.r.L.
Measurement of wind speed and wind direction. It can be combined with RH, temperature, pressure and radiation.
-
FST -
Fuji Electric Co., Ltd.
Three pairs of sensors for accuracy of ±0.2% of rate. Using the new algorithm for calculating the flow velocity, it can measure any type of fluid with high accuracy. Low maintenance. With no moving parts, FST has long-term stability while requiring only minimal maintenance work. Bubble resistant. By using the advanced anti-bubble measurement technology, the interference from air bubbles is greatly eliminated. Pipe diameter: 50 mm, 80 mm, 100 mm.
-
KATflow 150 -
Katronic
The KATflow 150 is the premier product for flexibility and performance, providing the user with a comprehensive specification and a list of configuration options. The practical modular design and the wide variety of different transducer types available ensure this instrument is suitable for everything from simple water flow measurements to energy flow monitoring and automated process control.
-
E3 -
Gentos Measurement & Control Co.
In times of increasing energy costs, it is important to measure and control energy consumption accurately. Energy Meters, commonly referred to as BTU meters or heat/ cold meter, can be defined by the measurement of heat/chilled water energy consumption.
-
ULTRAPROBE 2000 -
UE Systems Inc.
Designed for ease of use, it often takes no more than 15 minutes to become competent in testing with the ULTRAPROBE 2000 Kit Complete. Fast accurate diagnosis through the ULTRAPROBE 2000 System will dramatically reduce unplanned down time and shorten planned outage time.
-
SONAPHONE® Pocket -
SONOTEC GmbH
With the SONAPHONE Pocket you identify problems even before they arise and create value at all levels of your company. Just by detecting and eliminating leaks you can reduce the energy costs for your compressed air system up to 30 percent. This also has positive effects on your operational safety and system productivity through early warning of bearing failure and evidence of partial electrical discharges.
-
ULTRAPROBE 100 -
UE Systems Inc.
The Ultraprobe senses high frequency sounds produced by operating equipment, leaks and electrical discharges. It electronically translates these signals by heterodyning them down into the audible range so that a user can hear these sounds through a headset and see them as intensity increments on the meter. Heterodyning works the same as a radio in that it accurately transforms the sounds so that they are easily recognized and understood.
-
USF-2000A -
Shimadzu Corp.
The USF-2000A implements materials fatigue testing at 20 kHz. Consequently, it is possible to evaluate 109 to 1010 order fatigue strength, where it had been difficult to obtain data before. Also, data for 107 cycles can be obtained in about ten minutes.
-
Series P42 -
PIL Sensoren GmbH
The series P42-T/A sensors, all of which have an analogue 0-10V / 4-20mA output and two switching outputs, are programmed via an RS232 or RS485 interface. Characteristic curve, dead zone, set points, sensitivity, electronic filters, response time, and sensor addresses are optimally adapted to the measuring task. For communication with the computer, no special adapter is required, a direct access to the interface on the sensor is possible.
-
Series P49 -
PIL Sensoren GmbH
Cheap sensors for the price sensible market with high quantity.
-
VOLTA -
Innerspec Technologies, Inc
VOLTA features a patented pulser technology to satisfy the most energy-demanding EMAT applications in a compact and rugged package. Standard software built on Innerspec Technologies Operating Platform (ITOP) includes an intuitive menu to set up any EMAT application using standard sensors from Innerspec’s catalog for normal beam, angled beam, and guided waves.
-
SDT Ultrasound Solutions
Extend your inspection capabilities with ultrasound sensors and Improve Leak Detection And Tightness Testing
-
SEMIFLOW CO.65 -
SONOTEC GmbH
SEMIFLOW CO.65 non-contact clamp-on flow sensors are ideal to measure abrasive, adherent, corrosive, and ultra-pure liquids on rigid plastic tubes and pipes used in the semiconductor industry. Equipped with an integrated electronic unit, they function as a complete flow meter in the size of a small transducer without an external board or transmitter.