Power Calibrators
Verify power measuring instruments accuracy.
-
product
Power Amplifier
DPA8-0.4-22G-2032
Power Amplifier, Frequency 0.4~22GHz, Gain 40dB, Psat 30dBm, SMA Female
-
product
PON Power Meter
CARY-P100
The CARY-P100 PON Optical Power Meter was design for the FTTx application and maintenance which not only can be used to test and estimate the PON signals at the same time, but also the normal power measurement and fault identification. It is a useful, essential and ideal tool for the construction and maintenance of the PON projects.. Longlife battery power provides more than 8 hours outdoor test capability.
-
product
Power Supply 303d-II
PowerLab triple Series power supplies are reliable and accurate laboratory equipment with two outputs with adjustable and stabilized DC voltage and regulated ( limited ) power consumption and additional output has – voltage . Adjustable outputs can work independently , in series (max output voltage 120V DC for model 605- II) or parallel (max current of 10A for models 305- II and 605- II) . Power can be used in the design of electronic products , scientific works , laboratories, production lines and in teaching .
-
product
Powered VXI Crates
VXI-C Size 6021
WIENER C-size VXI mainframes of the 6021 deliver highest performance and reliability. Incorporating high density & lowest noise power supply technology the 6021 VXI series is the best choice for any demanding test and measurement VXI application.
-
product
Optical Power Meter
TL-520
TL520 Mini-Designed Optical Power Meter is a self-developed test instrument which is widely used for installation, operation and maintenance of fiber-optic network. TL520 can test optical power within the range of 800~1700nm wave length. There are 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm, six calibrated wavelength.
-
product
Power Quality Analyzer
PQPro
The PQPro™ is a portable 8 channel (4 voltage and 4 current) power quality analyzer that can stream high resolution waveform and RMS data to high capacity removable SD memory cards. Sampling rate can be adjusted from 64 samples per cycle to 1024 samples per cycle.
-
product
Power Quality Analyzer
High-precision Power Quality Analyzer and MeterThe Dewesoft power quality analyzer can measure all the power quality parameters according to IEC 61000-4-30 Class A. In comparison to other power quality meters ours are able to do more detailed power quality analysis. Raw data storing, behavior at faults, calculation of additional parameters, etc.
-
product
Thermocouple Power Sensors
N8482B
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
product
Power Probes
RkP-500 Series
The RkP-500 Series probes take advantage of synchronous detection (chopper/lock-in amplifier) technology to offer unparalleled background noise rejection, S/N ratio, and sensitivity. Total power, average power, and irradiance can be measured. The probes can be mounted directly onto the Rk-570C Optical Chopper to form an integrated measurement system, or the chopper can be operated remotely from the probe.
-
product
Power Quality Analyzer
PQM-710
PQM-710 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN. PQM-710 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-710 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display.
-
product
Class 1 Sound Level Calibrator
HD2020
The HD2020 sound level calibrator is a portable, battery operated sound source, suitable for sound level meters (portable and laboratory) and acoustic stations.
-
product
Wind Power Solution
ECO VESTAS
These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
Dynamometer Power Supply
DES Series
The DES 310 and DES 311 power supplies are suited to the entire range of Magtrol's Eddy-Current and Powder Brake Dynamometers. To avoid any disruption of the surrounding electronic modules, the DES 310 / DES 311 supplies are fitted in an industrial housing made of extruded cast aluminum. This housing must be installed directly on the test bench, as near to the dynamometer as possible.
-
product
Portable Calibration System
HD9120
HD9120 is an acoustic calibrator that, in accordance with the Circular Prot. RU 34143 of 02 December 2011, allows qualified technicians to perform calibrations of sound level meters for comparison with a reference sound level meter.
-
product
Power Divider/Combiner
Passive devices used mostly in the field of radio technology. They couple a defined amount of the electromagnetic power in a transmission line to a port enabling the signal to be used in another circuit.
-
product
Power Discrete Tester
Mostrak-2
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
product
Power Architecture SBCs
The most advanced multi-core Power Architecture processors enable you to achieve the high performance you need-whatever the demands of the application.
-
product
Power Meter
Beijing GFUVE Electronics Co.,Ltd.
One of the most useful and simple instruments to measure electrical power when no deeper analysis of the measured data is required.
-
product
Calibration Devices For Spring Impact Hammer
CX-TF06A
Shenzhen Chuangxin Instruments Co., Ltd.
Calibration Devices for Spring Impact Hammer
-
product
Industrial Power Supply
Mornsun Guangzhou Science & Technology
Mornsun offers one-stop solutions of power supplies for all types of applications: railway, automotive, photovoltaic, smart grid, medical, mining, etc.
-
product
Power Meters
AC/DC Power Meter for Single-Phase to 3P3W Equipment such as Motors, Inverters, Power Conditioners, and Power Supplies
-
product
DC Power Supply
Our broad selection of both bench-friendly and system-ready instruments can meet your testing challenges - from basic to complex - with a wealth of available capabilities.Test confidently with clean, precise DC power that's fully specified and guaranteedSafeguard loads from potential harm with robust output protection and fault detection capabilitiesEnhance system flexibility with built-in, DMM-quality measurement functions
-
product
Portable Calibration Shaker Table
AT-2030
The AT-2030 portable calibration shaker table is designed for simple accelerometer and vibration transducer calibration without the need for advanced features. AT-2030 shaker table and vibration calibrator is a variable frequency, variable amplitude, battery operated portable shaker capable of calibrating accelerometers, transducers, and proximity probes. Applications are producing a known vibration signal in g’s, mils, or ips for sensor, wiring, instrumentation, and system checkout in vibration condition monitoring applications.
-
product
Power Meters
The new range of Hobut multifunction panel meters feature 96 x 96mm sizes complete with unique blue LED screen, which can be seen in direct sunlight. The range is easy to use, features user-programmable CT & VT ratios, and can be used on any single or 3 phase system with any input voltage without re-programming.
-
product
DC Power Module, 8 V, 6.25 A, 50 W
N6732B
The Keysight N6732B 50 W basic DC power module provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power your DUT or ATE system resources, such as fixture control.
-
product
Power Supplies
CU-series
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
-
product
Power Analysis Software
PAS
PAS is SATEC's comprehensive analysis and engineering software designed to program and monitor all SATEC devices. It includes a variety of additional tools to assist in system setup, such as the communication debugging module.
-
product
Calibration Segment Arm
A torque analyzer or a torque sensor are a finely tuned instrument designed for testing and monitoring torque applications. In order to maintain accuracy, it is crucial that torque measuring equipment be properly calibrated regularly. Segment arm is engineered for calibrating torque analyzers and sensors and ensuring instruments are traceable to National or International Standards, such as N.I.S.T and ISO.
-
product
Calibration Solutions
Software
SPEKTRA Schwingungstechnik und Akustik GmbH Dresden
The CS18 software was created in close cooperation with the SPEKTRA Calibration laboratory accredited by DAkkS. It meets the demands of every efficiently operating calibration laboratory already in its basic configuration and can easily be adapted to the workflows of any company.
