Fiber Loopbacks
create a loop to test fiber optic I/O.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber
40-850A-314-HI
The 40/42-850A-314-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, ST Connectors
42-852A-518
The 40/42-852A-518 is a PXI/PXIe 8-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
L-Band Separate Raman Fiber Amplifier
RFA6000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
PXI/PXIe MEMS Optical MUX, Quad 2-Channel, Single-Mode, 9/125 Fiber, LC Connectors
42-855A-442
The 40/42-855A-442 is a PXI/PXIe quad 2-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Single 4 Ch Fiber Optic Multiplexer
40-810-014
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi- mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
Precision Fiber Optic Cleaver With Scrap Collector
HW-05C
Shanghai Fibretool Technology Co.,Ltd.
The HW-05C Fiber Optic Cleaver gives you high precision at low cost. This compact and easy to use cleaver is perfect for all cleaving applications, from fusion splicing to mechanical splicing and field installing quick termination connectors. The HW-05C works with both 250um coated and 900um buffered fibers.
-
product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X FC4 Simulyzer
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. With a simple firmware/software upgrade, a single function board can become a full function board without having to purchase new hardware.
-
product
Fiber Curl Measurement System
CURL500
The CURL500 is a fiber curl measurement system designed to produce accurate measurements quickly and with confidence. The CURL500 provides a high-resolution measurement that is consistent in its results, independent of the operator and is a first-choice tool for the QA manager keen to stay on top in the battle to maintain a quality and cost-effective production facility.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, FC/APC Connectors
42-852A-018-M50
The 40/42-852A-018-M50 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, FC/PC Connectors, With Interlock
42-850A-114-M50-HI
The 40/42-850A-114-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Identifiers & Talk Set
Fiber Identifiers and Talk Set are essential installation and maintenance instrument in data networks, CATV and telecommunication networks. Fiber identifier can identify the optical fiber by detecting the optical signals transmitted through the cables. Talk Set combines in one set the functions of both a digital optical phone and a stabilized light source. It is usually used in pairs, and can work over 80km. Fiberinthebox supply different types of Fiber Identifiers and Talk Set to meet you requirement, and they are with rechargeable battery and power supply adapter, so you can use them easily.
-
product
FAYb Fiber Laser Markers
LP-S500W Series
Panasonic Industrial Devices Sales Company of America
The LP-SW Series Fiber Laser Marker features:- Compact IP67G-Rated Head For Harsh Environments- Continuous Wave Black Annealing Laser- Marking Area Up To 160mm- Large Focal Tolerance- Removable Fiber Cable For Ease Of iIstallation
-
product
Variable Optical Attenuator Module for Multimode Fiber Applications
81578A
The Keysight 81578A variable optical attenuator is designed for multimode fiber applications and features lowest insertion loss and excellent wavelength flatness over a complete attenuation range of 60 dB, for characterizing optical network components for telecommunication and data communication in systems.
-
product
Digital Fiber Sensor
FX-300
Panasonic Industrial Devices Sales Company of America
Fiber Sensors have again taken another step forward. The deterioration of light emitting elements over time, previously accepted as unavoidable, as well as the conventional idea that Lenses could only be attached at the Fiber end, have now finally been overcome by Panasonic technology. A newly developed light eliminates deterioration, and by incorporating a Lens within the Fiber Sensor itself, stable long-range sensing for long periods of time is now possible for the first time ever.
-
product
Fiber Microscope
WL-C200S
The WL-C series fiber microscopes use coaxial illumination to provide users with maximum detail. It easily can detect the finest scratches and contamination, making it ideal for critically inspecting polish quality.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-318-M62.5-HI
The 40/42-852A-318-M62.5-HI is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Optical Fiber Type Hot Phosphoric Acid Concentration Monitor
CS-620F
In 3D NAND manufacturing process, dozens of layers of SiO2 and SiN are deposited, and the SiN layer is selectively removed using hot phos.In this process, the desired etching rate can be achieved by controlling the concentration and temperature of the chemical solution.Previous products have difficulty to measure high temperature chemicals, but the CS-620F is able to measure at high temperatures up to 170 C degrees.
-
product
Fiber Cable, Multimode, OM3, 50m
784184-50
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
MEMS Fiber Optical Switch at Single Mode 1315nm Type-A with LC/PC Connector
SUN-MS-1x8
Guilin GLsun Science and Tech Group Co., LTD
Fiber Configurations 1x8 MEMS Fiber Type SM, 9/125 umTest Wavelength 1310/1550 nm Operating Voltage 2.5VSwitch Type Non-latching Fiber Length 0.5m±5cmConnector TTL/UART Tube Type 900 umOperating Temperature -5°C~ +70°C Storge Temperature -40°C ~ +85°C
-
product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Multi-Mode, 62.5/125 Fiber, SC Connectors
42-855A-222-M62.5
The 40-855A-222-M62.5 (PXI) and 42-855A-222-M62.5 (PXIe) dual 2-channel multiplexers with SC connect are part of Pickering's range of PXI/PXIe Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Pigtailed Tapered Amplifier
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
product
Fiber Optic Sensor Systems
Fraunhofer Institute for Telecommunications
Fiber-optic and photonic measuring systems open up innovative measuring and control technology concepts for a wide variety of applications. They play a major role in optimizing energy efficiency and are important technological innovation drivers for new and future-oriented markets.In the Department of Fiber Optic Sensor Systems of the Fraunhofer Heinrich Hertz Institute, the focus of application-oriented research is on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication capability as well as extremely low power consumption or even a self-sufficient power supply.In the Department of Fiber Optic Sensor Systems at the Fraunhofer Heinrich Hertz Institute is focused applied research on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication skills as well as an extremely low power consumption, or even a self-sufficient energy supply.
-
product
Digital Fiber Sensor
FX-100
Panasonic Industrial Devices Sales Company of America
The ‘quick-set’ mode reduces set-up time while reducing the learning curve for inexperienced operators. As for experienced operators, the PRO settings are still available. Other features such as the ECO mode, copy and GET A functions, enhance its practicality in the workplace. A total product range of 12 types are available for all customer requirements.
-
product
Fiber End-face Interferometer
Anfkom International Co.,Limited
1.Automatic MeasurementSANA2 is equipped with the locking handle sensing unit to monitor the device locking status. To further simplify the testing process, the instrument can start the measurement once the device to be tested is fully locked. Operator can also click the button aside the locking handle to trigger the measurement.2.0~12° APC Angle Auto TuningBenefit with the unique fixture design, SANA2 can tune the APC angle precisely from 0°to 12°automatically, meeting any special requirement on APC angle setting.3.Simple and User Friendly Interfaces and Excellent 3D ImagesThe software of A 2 is simple and user friendly, you can change the language within the software. It provide many endface rebuild method such as 3D, 2D, plot to assist the engineers about the process. The test reports and data are generated automatically for analyzing and tracing.4.Auto Centering ImagesSANA2 has auto centering image function that can find the fiber and makes it to center automatically within one click.No mouse drag or hardware adjustment is needed.5.Cleave Angle Measurement
-
product
Fiber Optic Modem
VCH-608
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors
40-855A-512-M
The 40/42-855A-512-M is a PXI/PXIe 2-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI/PXIe MEMS Optical Switch, Quad Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors
42-860A-342
The 40/42-860A-342 is a PXI/PXIe quad insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Telecom Fiber Couplers
Thorlabs offers a varied selection of single mode (SM) and polarization-maintaining (PM) fiber couplers, as well as single mode 1x8 and 1x16 PLC waveguide splitters that have center wavelengths at common telecom wavelengths, including 850 nm, 1310 nm, and 1550 nm.
-
product
Erbium Fiber Frequency Comb
Detailed description of item: The AOSense frequency comb is a low noise, polarization maintaining (PM) device. Key features include a PM fiber architecture centered at 1550nm with turnkey modelocking; a free-running linewidth of the carrier-envelope offset frequency of <200 kHz; a temperature-insensitive all-fiber f-2f interferometer exhibiting fceo beatnotes with SNR > 45dB (300kHz RBW); and dual fast/slow cavity length actuators with a bandwidth of >300 kHz. The repetition rate of the comb is factory set and allows matching across multiple combs for dual comb applications. The optics package incorporates an optical heterodyne module designed for locking to the comb to an ITU-specified laser reference. The comb is capable of supporting an Allan deviation of < 5 x 10-18 at 1 second and ~10-20 after 105 seconds. Add-on features include all fiber extensions to visible wavelengths corresponding to several atomic transitions. An integrated comb electronics package is currently under development.
