DC Current Sources
-
product
Tunable Narrowband Terahertz Laser Source
TeraTune®
The TeraTune® provides a tunable narrowband terahertz source with a tuning range from 1.5 to 20 THz and a bandwidth of less than 100 GHz.
-
product
Low Power Programmable AC Source
Chroma Systems Solutions, Inc.
Delivers pure, instrument grade AC power at very low cost with output voltage from 0 to 300VAC, and frequencies from 15 to 1000Hz
-
product
AC & DC Electronic Loads
The Adaptive Power Systems Electronic Loads cover a wide range of power levels, voltage and current profiles and feature sets.Supported voltages range up to 1250Vdc or 350Vrms AC. From bench to system and DC or AC requirements, we can more than likely offer you the optimal programmable load to meet your needs.
-
product
Current Measurement Board
MS 1814
*Maximum DC Voltage Rating: 15V to 75V*Maximum DC Current: 5A*Output Voltage per 1A: 1V*Maximum AC Current: 5A*Operating Temperature: 0°C to 55°C*Storage Temperature: -20°C to +65°C*90% Relative Humidity (Non-condensing)*No. of DC Current Channels: 9*No. of AC Current Channels: 4nos*Maximum AC Voltage Rating: 230VAC*Channel Selection: Through 16 CH Analog MUX*Measurement Error Over Full Temperature Range: 5%*Type of Output: Proportional voltages*Maximum Voltage Drop across Series Resistor Full Scale Measurement: 0.05VDC
-
product
Clamp type AC Current Sensor/for Leakage Current Measurements(ZCT Series)
ZCT-30S
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Ultra compact size*AC 1mA~100A
-
product
UV Plasma Sources
UVS300|UVS 10/35
The UVS300 and UVS 10/35 are UV Plasma sources with high intensity, working with different gases.
-
product
Light Source Series
*High output power*Stable and reliable*CW or MOD output*MOD frequency: 270Hz/1KHz/2KHz*SMT, lightweight*Power supply by battery
-
product
Bulk Current Monitoring Probe
MP-50
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
product
Open Source Real-time Network Topology & Protocols Analyzer
Skydive
Skydive is an open source real-time network topology and protocols analyzer. It aims to provide a comprehensive way of understanding what is happening in the network infrastructure. Skydive agents collect topology informations and flows and forward them to a central agent for further analysis. All the informations are stored in an Elasticsearch database. Skydive is SDN-agnostic but provides SDN drivers in order to enhance the topology and flows informations. Currently only the Neutron driver is provided but more drivers will come soon.
-
product
DC Electronic Loads
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
NGI DC Electronic Loads
-
product
AC Current Transducer
iDVM 333
The iDVM 333 AC Current Transducer plugs into the iDVM 510 multimeter and measures current (as AC millivolts) with no need to break the circuit. Special Introductory Price: $52.50FeaturesTransformer jaws that detect AC current flowing through a conductorSelectable sensitivity between 1mV/A and 10mV/AHand Guard to protect your hand for safetyLarge, easy-to-operate trigger opens the transformer jaws
-
product
Relay Testing Voltage Source
PTE-FCN
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
-
product
AC DC Test Equipment
The products impress with a variety of technical features: TFT display, Ethernet interface, automatic test sequence to a fully electronic generator for even faster and more accurate tests. Our safety testers can be used both stand-alone without a PC as well as integrate with existing systems.
-
product
Logger with Current Clamp0 to 200A AC
TV-4810
As well as recording data the unit has a display that shows what the unit is currently reading. The unit has an IP65 case and features high reading resolution and accuracy, a large memory, a fast offload speed and a low battery monitor.
-
product
Single-Channel DC Powered Carrier Demodulator
CD16
The CD16 Miniature Carrier Demodulator is designed to deliver a 0 to 5 Vdc output from a variable reluctance transducer and operate from unregulated 9 to 55 Vdc power. A square wave excitation of 5 kHz is furnished to the transducer and the solid state integrated circuit amplifier and demodulator converts the transducer signal to an analog dc output. Zero and Span adjustments are made through access holes in the case.
-
product
Indoor Multi-Light source of Measurement System for PV Cell
King Design Industrial Co., Ltd.
The multi-light source measurement system is capable of execute I-V measurements by Real-Time One-Sweep Method (RTOSM), which not only removes the capacity effect but also meets the requirements of SEMI PV57-1214. The measurement process is controlled by designed program, thus the measured I-V curve, Pmax/Isc/Voc/… etc, could be exported automatically.This system is applicable to DSSC/OPV/Perovskite measurements.
-
product
Broadband Fiber Optic Light Sources
ASE Sources
Broadband fiber optic light sources utilize amplified spontaneous emission (ASE) within optically pumped rare earth-doped fibers. The spectral width of such light sources can be set by the developer in a range from a few nm to the full width of the emission spectrum of the active ion (e.g. erbium ion).
-
product
Controllable, Programmable AC Source Motorized
EAC / MT / SL
*Motor-controlled AC sources*Regulated motor-controlled AC source*Separate display for voltage and current*Regulated motor-controlled AC source*Separate display for voltage and current*Optional interfaces
-
product
High AC Current Capacitor
LC1/LC2/LC3-BN
Induction Heating Processing Equipment, Electric Current Welding, Resonant Circuits, Motor Controls; Oscillating, Bypass, Coupling circuits, High AC Current applications, High-Frequency AC Filter and Medium Frequency Power applications.
-
product
Split Type AC Current Sensor
CTF-24
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Wide measuring range (AC 0.1~200A).*Compliant with RoHS drective.
-
product
PoE Power Sourcing Equipment For TBOX300/tBOX400/tBOX500 Series
PSU120-259
*M12 5P DC input*Terminal block PoE power output, maximum 120W*Designed for tBOX300/tBOX400/tBOX500 series*CE, FCC, EN 50155 and IEC 60945 compliant
-
product
AC Current Sensor
RCTi and RCTi 3ph
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
product
Precision Current Sensing Resistors
PCR4T
Precision cement resistors designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow high precision measurements even with low resistance values. PCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a ceramic molding. This resistor has low inductance and has high pulse power.
-
product
Laser Source Simulator
MT1888 Series
The MT1888 products are state-of-the-art Laser Source/Spot Simulators (LSS) used for the testing of laser guided munitions such as the Hellfire & Hellfire II missiles, Paveway, and the AGM-65E Laser Maverick missile.
-
product
DC Loads
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik offers wideband multichannel DC decouplers for antenna diagnostic applications. Due its high bandwidth the device is suitable for all broadcast, cellular and Wi-Fi standards.
-
product
Open Source Machine Learning server
PredictionIO
The Apache Software Foundation
Apache PredictionIO is an open source Machine Learning Server built on top of a state-of-the-art open source stack for developers and data scientists to create predictive engines for any machine learning task. It lets you: quickly build and deploy an engine as a web service on production with customizable templates; respond to dynamic queries in real-time once deployed as a web service; evaluate and tune multiple engine variants systematically;unify data from multiple platforms in batch or in real-time for comprehensive predictive analytics; speed up machine learning modeling with systematic processes and pre-built evaluation measures; etc.
-
product
Eddy Current Sensor
eddyNCDT 3001
The eddyNCDT 3001 is a new, efficient eddy current sensor whose compact dimensions have to date only been reserved for inductive sensors and proximity sensors. The temperature-compensated design provides high stability even in fluctuating ambient temperatures. The eddyNCDT 3001 comes with integrated electronics, offering an outstanding price/performance ratio and easy operation. The eddyNCDT 3001 eddy current sensor is ideally suited to OEM integration and machine building applications. The sensor is factory-calibrated for ferromagnetic and non-ferromagnetic materials, which eliminates the need for field calibration of the sensor. The eddyNCDT 3001 is available with connector or with integrated cable. A robust design combined with the eddy current measuring principle enables measurements in harsh industrial environments (oil, pressure, dirt). In addition, the eddyNCDT 3001 is suitable for offshore/marine applications (salt water).
-
product
Miniature AC & DC Voltmeters
PM Series
The PM Series Full-functioned miniature digital voltmeters are AC or DC reading, and feature AC or DC power options, and LED or LCD displays. These versatile meters are available in 100mV, 200mV, 1V, 2V, 10V, 20V, 100V, 200V, or 1000V ranges. Highly accurate (up to 0.02% of full scale), with rapid update rates (up to three reading per second), these meters feature bipolarity (PM-3 is unipolar), a presettable decimal point, overload indication, an extensive list of application-specific options, and easy installation.
-
product
Hand held, Battery-Powered Voltage Source
DVC-350A
Hand held, lightweight 11 ounce (342 grams)Laboratory accuracy of 0.015% of FSR at +25 C, traceable to the National Bureau of Standards4 1/2 Digit LCD display100 V incrementsTwo output voltage rangeDecimal: 1.2V dc, 12V dcHexadecimal: 1V dc, 10V dc





























