Vibration Monitors
See Also: Vibration Test
-
Product
PH / ORP Monitor / Controllers
720 Series II
-
The advanced “isolated” circuitry of the 720 Series II pH/ORP Monitor/ controllers guarantees accurate and reliable measurements — completely eliminating ground-loop and noise issues. The unique sensor preamp allows for longer distances between the sensor and the Monitor/controller without the loss of accuracy or reliability.
-
Product
Monitoring System
A112
-
The photoelectric sensor model A112 allows to realize a system for detecting breaks of thin wires from 10 um in diameter, with a detection range greater than 50 cm.The A112 produces these results without the use of laser technology, allowing high immunity to vibration and a secure alignment between receiver and transmitter.
-
Product
Environmental Noise Monitors
-
Noise is one of the most complained about aspects of the environment, as not only does it have the potential to affect quality of life, it can also be difficult to monitor and therefore control. This type of noise is generally called environmental noise. There are many man-made sources of environmental noise, such as wind turbines, industrial sites, roads and traffic etc. If you are looking for equipment to measure noise in the workplace, look at sound level meters.
-
Product
Fault Recording Monitors
-
Comprehensive, flexible, scalable and compatible – full multi-function devices.
-
Product
Radio Monitoring and Signal Analysis
-
Shoghi has a full portfolio of products which fulfill the customer requirements for radio monitoring and signal analysis. Shoghi has a very robust SDR based wideband radio monitoring solution which can be implemented both in static or mobile versions for HF and VHF/UHF frequency bands. The Shoghi Radio Monitoring and DF system is the full-fledged product which provides the facilities for wideband signal reception and advanced signal analysis capabilities in addition to both wideband and narrowband D capabilities. The signal analysis capabilities include the ability to demodulate and decode both narrowband and wideband signals and advanced signal protocol analysis for detection of specific data protocols used in the intercepted RF signals.
-
Product
Remote Display Gas Monitor
Chillgard® 5000 Remote Display
-
The Chillgard® 5000 Remote Display provides gas monitor information before room entry where potentially hazardous gas levels may exist. It mimics the Chillgard 5000 Gas Monitor readings for gas concentration, alarm status, calibration.
-
Product
Monitoring Receiver
-
The portable monitoring receivers and remotely controllable analyzers were especially developed for signal search, radio detection, spectrum monitoring and frequency management.
-
Product
Contamination Monitors
-
Control of X-ray and gamma radiation personal dose equivalent.The dosimeter together with the PC reader and the software forms an efficient automatic system for staff radiation exposure control.
-
Product
SF6 Gas Online Monitor Test System
KVXJ
-
KV Hipot Power Test Equipment Co.,Ltd
KVXJ SF6 Gas Online Monitor Test System is mainly applied on 35KV SF6 500KV, 220KV, 110KV GIS in the substation to monitor the SF6 gas leakage in the SF6 combined electrical equipment room environment and the oxygen content in the air in real time.
-
Product
Event Monitoring System
Sigma 4
-
Sigma 4 utilizes the “Seismic Acoustic Monitoring” seismograph node. This is the most advanced, field-proven acquisition system in the world. It works seamlessly to provide the most fully integrated source control/recorder solution.*Autonomous Operation using Internal Storage*USB External Storage for Fast Data Collection*Use internal battery option or external power connection*Internal 3C geophone or external Geophone/Seismometer/Hydrophone/Microphone*Supports standard Ethernet equipment
-
Product
Frequency Generation & Monitoring
-
Timetech reference generators, phase comparators, and synchronized oscillators.
-
-
Product
Electrodynamic Vibration Test Systems
DC-series
-
Depending on the reference PSD or other operating conditions such as the specimen, one part of the controlled response may deviate from the reference PSD
-
Product
Joining Monitor
-
We are offering a variety of monitoring equipment for current, voltage, pressure and displacement which is indispensable for quality control of precision micro joining.
-
Product
Concrete Measuring and Monitoring System
IQM-Meter
-
Designed specifically for monitoring and analyzing fresh concrete, the IQM Module is programmed with the required Equivalent Age of the concrete under test. Once this preset maturity number is reached, a visual indicator will flash continuously, providing an effective, automatic indication that the concrete has reached the desired level of maturity.
-
Product
Wind Turbine Condition Monitoring
-
It has also become increasingly apparent in recent years that the wind turbine industry has recognised the importance of condition-based monitoring, especially for offshore wind turbines, where access is often limited.To increase reliability and minimise down time, many wind turbine manufacturers, owners and operators are turning to condition-based monitoring systems, aimed at predicting wind turbine maintenance issues, so that operators can quickly and effectively carry out predictive maintenance, repairs and replacements of components when needed, without the need for costly routine maintenance checks and visits. As a result, a condition monitoring system increases operational time, improves site performance and reduces maintenance costs for wind turbines, especially offshore ones.
-
-
Product
DVB-T/T2 Compact Monitoring Probe
EdgeProbe Nano DVB-T/T2
-
With its small, compact and easy to handle design, the EdgeProbe Nano DVB-T/T2 is the ideal tool for field technicians to transport in order to validate and monitor 24/7 all points of a DTV network.EdgeProbe Nano is able to monitor DVB-T and DVB-T2 signals through its RF input (144 x 137 mm compact format).Combined with a Network Monitoring System or not, the EdgeProbe Nano provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.
-
Product
Monitor Holder for 19" Rack Installation
ZZ-0017-01
-
- Monitor holder for 19 “rack installation- 9 U (400 mm)- Can be used universally with LED, LCD and plasma monitors- Compatible with the VESA standards 75 x 75 and 100 x 100 mm- Record in portrait and landscape format
-
Product
Structural Load Monitoring
SLM
-
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
-
Product
NI-9231, 8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module
783610-01
Sound and Vibration
8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module - The NI-9231 is a high-density sound and vibration module that can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. It can perform the high dynamic range measurements necessary for modern measurement microphones and accelerometers and features simultaneous sampling. The NI-9231 incorporates both a TEDS input path and 2 mA of IEPE signal excitation source that can be turned on and off, removing the need for external sensor power and reducing the complexity of the data acquisition system.
-
Product
Fixed Aperture RF Current Monitoring Probe
TBCP1-200
-
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
-
Product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
-
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
Product
Multi Wavelength Monitor
LV5490/LV5480
-
The LV 5490 is a multi waveform monitor that supports 4K video format (4096×2160、3840×2160) based on 3G-SDI dual link or quad link, HD-SDI quad link, and 12G-SDI. The following two 4K video division transmission systems are supported. ・2-SAMPLE INTERLEAVE DIVISION ・SQUARE DIVISION
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-23
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～120A*Current measurements of terminal feeder
-
Product
KOH Monitor
HE-960H-KOH
-
High precision, wide-range KOH monitor having chemical resistance sensor. Measurement range : 0 - 20%.
-
Product
Energy Monitoring Devices
-
Mitsubishi Electric Automation, Inc
Monitors all energy assets on the plant floor with EnergyPAQ a scalable energy hub and smart energy control capable solution with an HMI you can customize to show critical energy data, alarms in real-time and serve energy data to an energy information layer reporting software.
-
Product
Piezoelectric Vibration Pickup
PU-8ANSF
-
*Side outlet*Easy to remove due to cap nut type*Use up to 150 ℃ enabled
-
Product
OCM-C C-band Optical Channel Monitor
-
Optical Wavelength Laboratories
Features include: user-definable optical power threshold, selectable channel spacing (50 & 100 GHz), and data storage.Data can be viewed either as a bar graph or in tabular format, and the LCD display will automatically rotate based on the orientation of the OCM unit. Viewing in landscape mode allows for more viewing detail.
-
Product
Electrical Resistance (ER) Monitoring
-
The electrical resistance (ER) technique is an "on-line" method of monitoring the rate of corrosion and the extent of total metal loss for any metallic equipment or structure. The ER technique measures the effects of both the electrochemical and the mechanical components of corrosion such as erosion or cavitation. It is the only on-line, instrumented technique applicable to virtually all types of corrosive environments.
