UV Meters
measure irradiance of ultraviolet light.
-
Product
UV Cameras
-
Solar blind UV cameras are imaging devices optimized to detect ultraviolet light of wavelengths below about 280nm. Such cameras are insensitive against sunlight due to negligible sensitivity to visible and long wavelength UV light. Solar blind UV cameras are used in a series of applications like corona detection, fire detection, combustion analysis, plasma research, testing UV lamps, etc. However, highly sensitive corona detection is the main mass application and these devices are of crucial importance in electric power industry. These imaging devices enable easy detection of degraded insulators of high voltage transmission lines, distributions and substations. They can see the emission of UV light when discharges occur at defect insulators. From design point of view solar blind UV cameras are actually bispectral imaging systems built by combining true UV camera with typical visible camera. These bispectral imaging system generate output image as overlay of typical visible image with UV image of analyzed UV source.
-
Product
Moisture Meter and Thermal Imager with MSX®
FLIR MR265
-
The FLIR MR265 is a professional pin and pinless moisture meter with thermal imaging designed to show you exactly where to investigate issues related to moisture, air leaks, and insulation voids. Featuring IGM™ (Infrared Guided Measurement) and MSX® (Multi-Spectral Dynamic Imaging enhancement) technology, the MR265 helps you quickly scan and target problem areas, visually guiding you to the spot where you can confidently take measurements, analyze readings, and ensure that problems are fixed. Using FLIR Thermal Studio™, you can then create and share professional reports that include findings and proof of repairs – giving your clients peace of mind that mold, rot, or moisture challenges have been resolved.
-
Product
Meters for Reclaimed Water
-
Badger Meter offers precise revenue-generating measurement for non-potable water distribution. If your community is faced with increasing water costs and limited water resources, you may be considering installing or upgrading a reclaimed water distribution system. If so, make certain your system is equipped with meters from the Badger Meter family of Disc and Turbo Series meters exclusively for measuring non-potable water in residential, commercial and industrial applications.
-
Product
Micro Ohm Meter
-
The meter is used for testing cables under load condition. Available in various specifications and models, it is of great use in power generation sector.
-
Product
Magnetic Susceptibility Meter for Multi-Layer Survey
MULTI KAPPA
-
Multi Kappa instrument serves for fast field survey allowing both spot measurement and mapping by means of several probes. Together with GF Instruments traditional pocket magnetic susceptibility meters cover wide range of demands for accurate susceptibility measurement on ground surface, outcrops and samples of rock and soil. geological survey, archaeology, agriculture and forestry, raw material prospecting, mineralogy, sedimentology, detection of metallic objects, UXO survey.
-
Product
Concrete Moisture Test Meter
Rapid RH 4.0 EX
-
The Rapid RH 4.0 EX concrete test is superior to all other humidity measurement systems on the market today. Rapid RH 4.0 EX concrete moisture tests equilibrate faster than other concrete moisture tests. The reading taken one hour after installation for concrete relative humidity content will be within 3% of the final reading.
-
Product
Field meters
-
Small, lightweight and low priced non frequency selective Efield meter. It can be used for relatively high field strengths e.g. to observe the field in a TEM cell or a strip line.
-
Product
Pressure Meters
-
Ensure optimal pressure levels across several circumstances with our pressure meters. Netech offers four versatile digital pressure gauges suitable for numerous medical and industrial applications. These devices also perform vacuum gauge measurements.
-
Product
Turbidity Meter
-
Anton Paar turbidity meters are indispensable plug-and-play modules that are easily integrated into Anton Paar’s multi-parameter laboratory measurement systems. These add reliable turbidity analysis to a variety of monitored parameters. Covering a wide temperature range from -5 °C to 40 °C and featuring a built-in, solid-state Peltier thermostat for independent operation, these meters will bring crystal-clear clarity to your cloudy media.
-
Product
Clamp Meter 6000counts Ture RMS
VA312 /VA315
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Clamp meter Diode Test Auto Range Continuity Buzzer MAX/MIN Value Measurement.
-
Product
TSS Meter
LD-LTSS-A10
-
TSS meterLD-LTSS-A10is a tabletop meter with a dual-beam infrared scattered light photometerdetection system for enhanced stability. Built-in self-diagnosis function to ensure dataaccuracy. Optional cleaning brush for automate cleansing function to reduce the sensormaintenance.
-
Product
Sonin Digital Moisture Meter 270
50270
-
This compact easy-to-use Digital Moisture Meter is ideal for anyone needing to measure the moisture content in soft and hardwoods including tropical species.
-
Product
Optical Wavelength Meter
-
Optoplex Optical wavelength meter (OWM) uses proprietary thin-film interference filter in conjunction with Fabry-Perot cavity technology combined with a micro-actuator and high-speed electronics. Its working principle is schematically shown below. By comparison with Optical channel monitor / Optical performance monitor, the proprietary wavelength reference unit is introduced to ensure high precision wavelength measurements. Optoplex Optical wavelength meter is the only DWDM wavelength meter capable of measuring wavelengths of multi-lasers in DWDM networks over C-band and L-band wavelength range with a high accuracy better than that the wavelength locker can provide. For example, the device can simultaneously report 80 wavelength values of 80 channels at 50 GHz channel spacing with the wavelength accuracy ± 2 GHz. DPRAM, RS-232, or USB interfaces are available and OWM can be customized to meet specific requirements.
-
Product
Quadrature Position & Rate Meter
-
Accepts low-level differential or single-ended 5 V logic level quadrature signals from shaft encoders to display scaled position or scaled rate. One, two or four transitions may be counted at a maximum combined rate of 250 kHz and be mathematically scaled to display in engineering units from -999,999 to +999,999. An analog output scaled to the display and relay outputs are optional.
-
Product
Clamp Meters
-
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
Product
Portable Electricity Meter Testers
EE-120A-3S
-
The EE-120A-3S unit consists of a three-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types of electricity meters using the voltages of the network. The meter error can be measured for active, reactive or apparent energy in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Maximum Demand Test, Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the three-phase network – with direct measurement or with optional current clamps.
-
Product
Panel Meter
-
A panel meter is an instrument that displays an input signal in either a digital or analog form. Many panel meters also include alarm options as well as the ability to connect and transfer data to a computer.
-
Product
Turns Ratio Meter 1 Phase
TR-1 / TR-1P
-
Raytech Single Phase Transformer Turns Ratio Meter TR-1/P was designed to be a rugged and reliable automatic transformer Ratiometer. This system has a high degree of accuracy and will test ratios to 4000:1. The design of this test system is based upon the popular Raytech Automatic Three Phase test set: TR-Mark III.
-
Product
Electricity Metering Device- Residential
Mk32H
-
Designed for residential use, Mk32H is a DIN Rail single phase meter with integrated 100A UC3 compliant relay. It is able to operate in either STS compliant prepaid mode or post-paid mode.Mk32H can operate with the EDMI CIU (Customer Interface Unit) – HD18 wirelessly as a split meter as well as operate with EDMI gateway – GW30 and the EDMI Head End System – MultiDrive as a complete AMI system.
-
Product
Meter Test System
MTS-122
-
Kongter Test & Measurement Co., Limited
This rugged Meter Test System is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 36A). This system is particularly designed with modular structure for calibration and test of analog meter, digital meter, RTU, electrical transducer, energy meter and so on. It is operated under high functionality with user friendly interface.
-
Product
Optical Power Meter
PM-03D
-
Hangzhou Tuolima Network Technologies Co., Ltd.
PM-03D PON Optical Power Meter is designed base on PM-03D PON power meter. This power meter is able to simultaneously test and estimate the signals of the voice, data and video. It is an essential and ideal tool for the construction and maintenance of the PON projects
-
Product
Class 2 Sound Level Meter
SP79
-
The SP79 is a Class 2 sound level meter for on-site measurements in accordance with Noise at Work legislation in industrial and office environments. Featuring A and C frequency weighting and fast and slow time weighting, the compact design can be handheld, or mounted on a tripod for longer term monitoring of Min / Max values. Detailed recording and analysis can be made using the AC and DC outputs. The SP79 complies with BS EN 61672-1:2003 and is supplied with a detachable windshield and hard carry case. The large high contrast display includes both digital reading and analogue bar graph. An optional Class 2 sound level calibrator is available to verify accuracy before and after readings in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB.
-
Product
Single Channel Universal Power Meter
8651A
-
The Spanawave/Giga-tronics 8651A Single Channel Universal Power Meter has the extensive measurement capabilities and features you need to test today's sophisticated communications systems faster, easier and more accurately.
-
Product
AC/DC Clamp Meter
3900 CL
-
Standard Electric Works Co., Ltd
● 4000- count LCD.● Full automatic measurement. ◎ Voltage measurement. ◎ Current measurement. ◎ Resistor measurement. ◎ External frequency measurement.● Range change function.● Data Hold function freezes the reading.● REL function.● Peak function.● VAHz mode measures frequency in ACV and ACA mode.● Max/Min function.● Continuity check.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
Product
VFL Power Meter -- VFL & OPM
TM203N
-
◇ Self Calibration◇ Self Auto Off◇ High Accuracy, high ,High sensitivity, high linearity-◇ Stable VFL Output◇ Set the REF Value◇ Real-time display of the power consumption◇ Interchangeable connectors: FC/ SC◇ Rubber Out shell, increased the protective properties for field work
-
Product
Peak Power Meter and Spectrum Analyzer,
WiPry-Combo
-
peak power meter and spectrum analyzer: Pry into the power, spectral, and time characteristics of your signals with an easy to use integrated solution.
-
Product
Multifunction Meter
-
Nippen Electrical Instruments Co.
VAF meters measure Voltage , Current and Frequency. Additionally, it measures RPM and Run hour.
-
-
Product
T Series Panel Meter
ST-95
-
Standard Electric Works Co., Ltd
● Hz Meter : Measuring Ranges : 45~56 Hz, 45~55 Hz, 55~65 Hz Rated Voltage : 110V, 220V Accuracy : ± 2.0% full scale● Case and Composition: ABS case and PC cover Four studs mounting● Accuracy : ± 2.0% full scale value● Color：Black case and white scale plate.● Pointer：Knife-type, color in black.
-
Product
6000 Series （Power Meter）
-
Digital Power Meter is designed to measure the power line parameters of AC / DC and DC / DC power supply. It is suitable for AC / DC Adapter, Charger, Quick Charger, LED Driver and DC / DC Converter. It is also suitable for uninterruptible power supply UPS, Regulators AVR, Inverter, batteries, AC / DC power supply / components ... and other applications.
