VSWR
Voltage Standing Wave Ratio.
-
Product
High Flexibility VNA Cables
-
Our lines of high frequency VNA test cables display excellent electrical properties such as wonderful phase stability of +/- 6° at 50 GHz and +/- 8° at 67 GHz as well as VSWR of 1.3:1 at 50 GHz and 1.4:1 at 67 GHz. The 50 GHz assemblies are terminated with 2.4mm connectors while the 67 GHz versions utilize 1.85mm connectors. The braided stainless steel armoring surrounding the coax provides a rugged, but flexible cable with a flex life exceeding 100,000 cycles, making these test cables ideal for use in semiconductor probe testing, precise bench top testing as well as lab/production testing where the need for a highly flexible, yet durable cable solution is required. The VNA test cables are also equipped with rugged stainless steel connectors that provide up to 5,000 mating cycles when attached with proper care. Additionally, the flexibility of these cables makes it easier and safer to test a Device Under Test (DUT). A swept right angle 2.4mm and 1.855mm connector option allows these cables to fit in tight spaces and can reduce the length of cable required in many applications.
-
Product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 50Ω, MCX
42-874A-102
Multiplexer Module
The 40-874A-102 (PXI) and 42-874A-102 are 50 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
DC Blocking Power Splitter Combiner
PD5060
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) 50 Ohm
-
Product
PXI/PXIe MEMS RF Multiplexer, Single 4-Channel, 4GHz, 50Ω, SMB
40-878-211
Multiplexer Module
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
Product
Low Noise Super Wide Band Amplifiers
WBA Series
-
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
Product
Low PIM Coaxial Cable Assemblies
-
For applications that demand low VSWR, low insertion and low PIM cable assemblies; RFI now offers semi-rigid and corrugated cable assemblies with factory soldered N and DIN connectors. Assembled using the latest soldering equipment for years of performance reliability. Each assembly is tested for insertion loss, VSWR and PIM rating and is shipped with individual test data. Available using flexible or super flexible corrugated cables with a standard or fire retardant jacket.
-
Product
PXI/PXIe RF Multiplexer, Single 8-Channel, 3GHz, 50Ω, MCX
42-874A-101
Multiplexer Module
The 40-874A-101 (PXI) and 42-874A-101 (PXIe) are 50 Ohm 8 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI Dual 6 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-881-002
Multiplexer Module
The 40-881 is a 50 Ohm 6 to 1 6GHz multiplexer available as a single or dual MUX in one and two PXI slots respectively. The 40-881 exhibits low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the 40-881 ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
Product
Connectors
-
Optimized Super SMA Connectors feature a 32 GHz operating frequency, leading the market in precision reflection (VSWR) performance. MegaPhase, with its team of design experts, drives innovation in RF/Microwave connectors and improvement of interconnects supporting aerospace, satellite, military and telecommunication applications. These connectors are Space Qualified.
-
Product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 50Ω, MCX
42-877A-101
Matrix Switch Module
The 40-877A-101 (PXI) and 42-877A-101 (PXIe) are 50Ω 2x2 RF matrices with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 50Ω, MCX
42-872A-102
Multiplexer Module
The 40-872A-102 (PXI) and 42-872A-102 (PXIe) are 50 Ohm 4 to 1 PXI RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of this RF MUX has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI-2554, 2.5 GHz, 75 Ω, 4x1 PXI RF Multiplexer Switch Module
778572-54
Multiplexer Module
2.5 GHz, 75 Ω, 4x1 PXI RF Multiplexer Switch Module—The PXI‑2554 is ideal for use in video RF applications where high-frequency video signal reflections can damage the source. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
Heat Exchangers RF Coaxial Loads
86500 Series
-
The 86500 Series Heat Exchangers are ideal for areas where water is limited. The loads are rugged, self-contained, easily operated, and portable units capable of dissipating up to 80 kW of RF power from DC to 800 MHz with a VSWR of 1.10:1.
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, 3GHz, 50Ω, MCX
42-872A-104
Multiplexer Module
The 40-872A-104 (PXI) and 42-872A-104 (PXIe) are 50 Ohm 4 to 1 RF multiplexers available with 4 banks in a single PXI slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Cable & Antenna Analyzer
CAA-100A
-
DTF/Frequency Return Loss, VSWR, Cable Loss, RF Power and Spectrum. CAA-100A integrates two functions: cable and antenna measurements and spectrum analysis. Cable and antenna analyzer with frequency range 1MHz – 4.4GHz and 60dB dynamic range can suitable for 2G/3G/4G/WiMAX system etc.
-
Product
PXI Dual 4 to 1 RF Multiplexer 3GHz 50 Ohm SMB
40-872-002
Multiplexer Module
The 40-872-002 is a 50 Ohm 4 to 1 PXI RF MUX with 2 banks in a single PXI slot. It exhibits low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of this RF MUX has been minimized by careful attention to the mechanical and electrical design.
-
Product
E- And W-Band Test Assembly
StormFlex® 047EW
-
An SF047EW assembly offers test engineers, application designers, manufacturers of mmWave applications the proven durability and robustness of Storm Flex® 047 cable, optimized for coaxial connectivity at frequencies up to 110 GHz.SF047EW cable can withstand handling and flexing and while maintaining the original Insertion Loss and VSWR performance at frequencies previously addressed by waveguides.
-
Product
Fixed Attenuators
-
The Analog Devices family of wideband, fixed value, 50 Ω matched attenuator products offers relative attenuation levels that range up to 20 dB. Our products are ideal for microstrip, hybrid, and multichip module applications that require extremely flat attenuation and excellent VSWR vs. frequency.
-
Product
Double Ridged Waveguide Horn
DRH20E
-
Frequency range: 1.6 GHz - 20 GHz VSWR (max): < 1.5:1Impedance: 50 O (Ohm)Connector: SMA female Power (CW / Peak): 50W / 100 W
-
Product
RF Power Splitter, Combiner, Divider IP67, 4 Way, N-Type Female, 2.4 - 6.0 GHz
PD2478
-
INSTOCK Wireless Components, Inc
Wideband Frequency (2.4 - 6.0 GHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (25 dB avg)Excellent VSWR (1.25 : 1 avg)Outdoor Weatherproof ConstructionTri Alloy Type N Female (Jack) Low PIM
-
Product
Double Ridged Waveguide Horn
DRH18-EX
-
Frequency range: 800 MHz - 18 GHz VSWR (AVG): < 2.4:1Impedance: 50 O (Ohm)Connector: SMA female Power (CW / Peak): 100 W / 170 W
-
Product
Double Ridged Waveguide Horn
QRH18
-
Frequency range: 1 GHz - 18 GHz VSWR (max): < 2.5:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
Product
RF Power Splitter, Combiner, Divider IP67, 3 Way, SMA Female, 2.4 - 6.0 GHz
PD2568
-
INSTOCK Wireless Components, Inc
Wideband Frequency (2.4 - 6.0 GHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (20 dB avg)Excellent VSWR (1.25 : 1 avg)Outdoor Weatherproof ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
RF Power Monitors
-
Bird's RF Power Monitor family includes a range of products that not only measure power and VSWR but also provide hard contact alarms to protect your system in the event of a system failure – the IP-enabled, BPME is even capable of emailing a failure notification.
-
Product
SP1T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
Product
L Band Splitter, DC Block All Ports
PD5022
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
Keysight Triple 1x2 SPDT Unterminated Microwave Switch Module for 34980A
34947A
Microwave Switch Module
The Keysight 34947A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as three independent 1x2 (SPDT) unterminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
Product
Digital RF Power &V.S.W.R. Indicator
PowerMaster Series
-
Thank you very much for purchasing the Array Solutions PowerMaster Series RF Power/VSWR Indicator. The PowerMaster represents a breakthrough in features for measurement of the performance of your transmitting system. Microprocessor control insures fast capture time and low power consumption. With the ability to monitor your VSWR and power levels at all times, you will know that your transmitter, RF source, and load, or antenna systems are operating effectively and safely. In addition, the power and VSWR relay alarms can quickly shut down your power amplifier system and alert you to the alarm condition. This places an additional layer of protection in your transmitting system to help preserve expensive tubes and finals. The PowerMaster also features the ability to be monitored and controlled from a PC via the bundled software, and the unique ability to be monitored and controlled over a LAN or from the internet. PowerMaster firmware updates will be made available for download from the Array Solutions website as they becomeavailable. This means that the user can take full advantage of features or enhancements just by installing the firmware update. No need to return the meter to the factory for updates.
-
Product
PXI Triple SPDT RF Switch MCX 75 Ohm
40-830-103
Switch Module
The 40-830 is a 75 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-830 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
