Audio Cable Testers
-
Product
Audio Cable Testers
AudioJog Pro 3
-
Audio cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection .
-
Product
12 Plug Pro Audio Cable Tester
PCT40
-
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections
-
Product
Audio Cable Tester
CBT-500
-
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
Product
Audio Cable Testers
AudioJog Pro 5
-
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
8 Plug Pro Audio Cable Tester
PCT10
-
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections3.5mm TRS Jack1/4' TRS Jacks3 Pin XLR Male3 Pin XLR FemaleRCA Phono4 Pin SpeakonBanana Plugs9V Batter (Not Included)
-
Product
Performance Audio Analyzer
U8903B
Audio Analyzer
Measure your most demanding audio devices with higher accuracy and a low residual distortion of -110 dB See the real performance of your devices with the highest resolution audio measurements available Automate testing with built-in test sequences Meet standards more easily with pre-configured POLQA and PESQ measurements Simultaneously measure/view up to eight channels on a single screen in real time Configure for specific applications with digital audio interface (AES3/SPDIF and DSI) and Bluetooth audio measurements options
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
PXIe Audio Analyzer
M9260A
Audio Analyzer
M9260A is significantly different from the traditional general purpose PXI digitizer modules which are being used for today's audio measurement. In order to achieve fast test speed and high performance it comes with large one million sample arbitrary waveform buffer and one million sample "limitless" input buffer, as well as super-linear/low noise amplifiers and digital to analog converters. This enables M9260A's ultra-low residual distortion and high amplitude accuracy. M9260A is now an important part of Keysight Radio Test Solution, and may also be easily integrated into any audio related PXI test system with its developer-friendly drivers and commands.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Sound Harmonics and Current Analyzer
H74050100
Audio Analyzer
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
Product
68-Pin VHDCI Male to 68-Pin, Female SCSI, Twisted Pair, Basic Shielded Multifunction Cable
191945-02
Multifunction Cable
SHC68-68, Twisted Pair Cable with Basic Shielding, 2 m
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 100-Pin Male SCSI
540009010240
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 36", 100-Pin Male SCSI
-
Product
Cable Assembly, Receiver, Tripaddle, 36", for PXI-2527 (uses NI TB-2627)
541123199
Cable Assembly
Cable Assembly, Receiver, Tripaddle, 36", for PXI-2527 (uses NI TB-2627)
-
Product
8-Pin M12 Male To 8-Pin M12 Male (Right-Angle), Shielded, FieldDAQ M12 Ethernet Cable
785945-01
Ethernet Cable
IP67 Gigabit Ethernet, Shielded X-Code M12 Male to Shielded M12 Male (Right Angle), 1M for FieldDAQ
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated to Tinned Ends, 1 Amp, 2m length, 500 Port
A500RMR-T-1B200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to to products using the 500-Pin SEARAY connector.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-025-1m-MU
Cable Assembly
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly, Receiver, 36", Mini Power, 4 Banana Plugs, 1 KV for PXIe-4081
540067030208
Cable Assembly
Cable Assembly, Receiver, 36", Mini Power, 4 Banana Plugs, 1 KV for PXIe-4081
-
Product
Cable Assembly, 104-Pin D-Type, Male to Unterminated, Ferrules, 2A, 1m
40-972-104-1m-MU
Cable Assembly
This 1m long male to untermiated 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable and has unterminated ends with ferrules.
-
Product
Cable Assy 25-Pin D-Type M/M 2m
40-970-025-2m-MM
Cable Assembly
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 25-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 200 Pin Male LFH w/ M3 Jackscrews
540105010205
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 200 Pin Male LFH w/ M3 Jackscrews
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Tinned Ends, 2m
A015DF4-T-0A200
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Cable Assembly 15-Pin D-Type, Female to Female, 0.5m
40-970-015-0.5m-FF
Cable Assembly
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products.
