DC Shunts
A resistor which delivers a millivolt of DC output in proportion to the current flowing through the resistor.
-
Product
Coaxial Fixed Attenuator, DC to 18 GHz
8491B
Attenuator
The Keysight 8491B coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. It has type-N connectors with a maximum frequency of 18 GHz. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Programmable DC Power Supply
CBCT
-
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
Product
Bench/System Multi-Range DC Power Supply With Digital Control, 3 Or 4 Outputs, 315 To 420W With/without Remote Interfaces
MX Series
-
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
Product
High Power DC Electronic Load
34000A Series（5KW~40KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
Coaxial Switch, DC to 18 GHz, SPDT, 24 to 30 V Solenoids
8761B
-
The Keysight 8761B is a single-pole, double-throw coaxial switch with excellent electrical and mechanical characteristics for 50 ohm transmission systems operating from dc to 18 GHz. It features broadband operation, long life, low SWR, excellent repeatability, and magnetic latching solenoids. The Keysight 8761B switch is small and lightweight, making it ideal for applications where space is limited. Because of its versatility and excellent electrical performance, it is well suited for automated testing and systems applications.
-
Product
Programmable Linear DC Power Supply
MPS-S Series
-
Triple channel programmable DC power supply is with high resolution, high precision and high stability, over-voltage and over-heat protection are available. Series and parallel operation are also provided. The resolution is 10 mV/1 mA.
-
Product
Rack Mount Kit For N8900 Autoranging System DC Power Supplies
N8958A
Mounting Kit
The N8958A is a rack mount kit that provides all the necessary hardware to rack mount one N8900 Autoranging System DC Power Supply (any of the 28 models) in only 3U of rack space when installing in a Keysight rack.
-
Product
Adapter, 1.0 mm (m) to 1.85 mm (f), DC to 67 GHz
11921G
-
The Keysight 11921G precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
Product
Regulated DC Power Supply
PAR-A Series
-
This instrument is a single-output, direct-current stabilized power supply of the dropper type.It is capable of high stability and high precision output with low noise.Multiple interfaces can be added selection.
-
Product
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 60 V, 0 A, 6 A
T3PS16006
Power Supply
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 60 V, 0 A, 6 A.
-
Product
DC Power Systems
-
Allow efficient distribution of your telecom and data center power utilizing these reliable, scalable and flexible DC power products.
-
Product
700 W VITA62 PSU | conduction cooled | 6 U | 5 HP | DC
MS216479+RC
-
Designed to meet the requirements of VITA 62 for use in harsh environments. For use in DC systems, they are 6 U high by 5 HP (1-inch) wide modules with guide blocks, for use in conduction cooled VPX systems.
-
Product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 8 Prescaler
HMMC-3028
-
The HMMC-3028 is a DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
Product
Battery and Alternator Analyser for 12V DC Systems
1176
-
Checks battery charge level and alternator output level. 880mm of insulated cable with test probe and earth (crocodile) clip. For 12V DC systems only. Display packed.Warning: For testing DC circuits on vehicles within the voltage range only. Not suitable for testing mains supply AC circuits.
-
Product
Multiport Electronic Calibration Module (ECal), DC To 9 GHz, 6-ports
N7562A
-
A series of multiport ECal that cascade-able up to 36-ports which makes it possible to calibrate a wide frequency range from DC up to 9 GHz without making numerous connections during calibration process. Ideal for multiport measurement application with VNA in such as high-volume PA/FEM, massive MIMO antenna or high-speed digital interconnect test applications
-
Product
Adapter, 2.4 mm (f) to 2.4 mm (f), DC to 50 GHz
11900B
-
The Keysight 11900B is a metrology-grade, 2.4 mm female to 2.4 mm female adapter with dc to 50 GHz operation.
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
Product
Programmable DC Electronic Load
-
Programmable DC electronic load is a device that precisely regulates the load voltage and current dissipation power consumption of electrical energy. There are several important parameters to consider when choosing programmable DC electronic load, including maximum power, maximum current, maximum voltage, current slope, and so on. Each indicator is related to the needs and applications we actually test.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
-
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
Product
FaithTech FTL Series High Precision DC Power Supply (90W-1500W)
FaithTech FTL Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FTL series is a high precision DC linear power supply with high performance, multi-function, medium and small power features. The product is stable and mature, and has comprehensive protection functions such as reverse polarity, overvoltage, overcurrent, overload and overtemperature, which can keep the power supply and load safe in unstable environments. FTL has a regulation rate of < 0.01%, ripple and noise of < 1mVrms and fine transient performance, and is suitable for application environments like current surges. The FTL series DC power supply is not only suitable for high-grade laboratory, but also for high-performance test systems.
-
Product
High Voltage DC Electronic Load
3360F Series（600W~14.4KW）
-
3360F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232,USB and LAN interface.
-
Product
DC Power Supply With Scope, Arbitrary Waveform Generator, And PathWave BenchVue Software Bundle
E36155ABV
DC Power Supply
Better value bundle of E36155A DC power supply, single-output, auto-range: 60V, 40A, 800W: LAN, USB, E36150ADVU, and BV9200B BenchVue Advanced Power Control Analysis – Four Instruments Connection.
-
Product
I/O Board With One GbE LAN, VGA And DC Jack For PICO841, PICO843
AX93267
-
*Specifications: 1 x DC jack, 1 x VGA, 1 x Gigabit LAN*Dimensions: 100 x 26 mm*Compliant products: PICO841, PICO843
-
Product
DC Power Supplies
XG 1700
-
AMETEK Programmable Power, Inc.
The XG 1700 is an industry leading programmable DC power supply designed for test, production, laboratory, OEM and quality assurance applications. The XG 1700 is a 1700 Watt, 1U programmable power supply with constant voltage and constant current modes, automatic cross-over and numerous features enabling cost effective, easy integration.
-
Product
Programmable Step Attenuator, DC to 50 GHz, 0 to 65 dB, 5 dB steps
84908M
Attenuator
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
Product
Coaxial Transfer Switch, DC to 50 GHz
87222E
-
Flexibility is essential in signal routing applications, and the Keysight 87222E 4-port coaxial transfer switch offers just that. It provides exceptional repeatability, low insertion loss, and high isolation. These switches provide simplification of design in signal routing and conditioning applications. The Keysight 87222E can be used in a variety of applications such as, a drop-out switch, switching two inputs and two outputs, or signal reversal switching.
-
Product
DC Power Module, 20V, 2.5A, 50W
N6733B
Power Module
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
AdvancedTCA, Type 11A, 13U 19" Vertical, DC
11A14FGCD8Y4VNXX
-
Elma's ATCA, DC, 13U vertical enclosures with backplane 14-Slot Dual Star or Mesh backplane, shelf management, and options. PEMs with availability (99.999%). 19" rackmount vertical ATCA chassis for carrier-grade applications.
-
Product
DC Power Services
-
At Eagle Eye Power Solutions, service isn’t an afterthought — it’s built into everything we do. From precision installations to expert maintenance and hands-on training, we’re here to keep your critical power systems running strong, compliant, and ready for whatever comes next.
-
Product
Multiport Electromechanical Coaxial Switch, DC to 40 GHz, SP4T
87104D
-
The Keysight 87104D multiport switch improves signal accuracy in RF and microwave signal routing and testing applications. This high performance electromechanical switch provides unmatched isolation and a 0.03 dB insertion loss repeatability, which is warranted for the 5-million life cycle of the switch. The 87104D’s low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy. The repeatability and reliability of this switch guarantee measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications.
