Starter Testers
See Also: Starter, Alternator Testers
-
Product
Peeling Tester
BN-3
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
Product
Voltage Tester
HW313
-
Wenzhou Zhengyuan Electronic Co., Ltd.
Digital live-wire voltage reading
-
-
Product
Traction Battery Drop Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
Traction Battery Drop Tester Relevant standards requirementsSingle Storage Cell Safety TestDropt testing steps：Charge the single storage cellaccording to 6.1.3Drop the positive negative terminals of the cellfrom the height of 1.5m to the concrete floor；Observe for 1hBattery Module Safety TestCharge the battery module according to the standard 6.1.4Drop the positive negative terminals of the battery from the height of 1.2m to the concrete floorObserve for 1h
-
Product
Professional Cordless Circuit Tester
CT8002
-
No Ground or clip required. No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance Electronic circuitry. Safety V-groove needle accessory for piercing and carrying. Negligible current draw ( 20 micro-amps) is 10,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 3 and 28 Volt DC in battery powered systems.
-
Product
Lan Cable Tester
3PK-NT015N
-
Open/short wiring testConnected wires displayNo wire or termination indicationWrong connection / Non-parallel connectionEthernet 10 base2 termination value detectionBattery low indicationBuzzer insideBNC for testing 10 BASE2 terminator valueIsolation resistances 50 K ohms test
-
Product
Cardboard Puncture Tester
DRK104A
-
Shandong Drick Instruments Co., Ltd.
DRK104A cardboard puncture tester is used to test the corrugated board anti-pierced performance (puncture strength). It has the snap-operating handle, automatic reset and safety protection function. It is the indispensable instrument for carton manufacturing plants, research and quality supervision, inspection and other enterprises and departments.
-
Product
Ultrasonic Portable Hardness Tester
MET-U1A/MET-U1A50/MET-U1A100/MET-U1A110
-
The PHASE II ultrasonic portable hardness testers are capable of measuring the surface hardness of a broad variety of metals on flat, round, thin or large surfaces. Unlike the standard Dynamic hardness testers, these "state-of-the-art" portable hardness testers incorporate "Ultrasonic UCI" technology, which enables the hardness testing of very thin and small workpieces, which otherwise could not be tested accurately using a portable device.
-
Product
Universal Safety- & Function Tester
GLP2-BASIC
-
The variety of features, e.g. to create your own test sequences, to enter your own data as serial number, result storage, freely configurable label print out, barcode function and many more leave nothing to be desired.
-
Product
3-48V Auto Tester
1960A
-
Peaceful Thriving Enterprise Co Ltd
Check on 3-48V systems. Especially suitable for the control of electrical and electronic parts of motor vehicles, for the fault finding on components. The tester is connected with a banana plug adapter, including a testing probe and an alligator clip.
-
Product
Portable Winding Resistance Tester
-
1. Handheld winding resistance meter2. Conversion function for standard temperature resistance.3. 500 test data can be saved and download by flash disk.4. Temperature testing function.
-
Product
Anaerobic Jar Tester
LD-LAJ-A10
-
Anaerobic JarLD-LAJ-A10with 1.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
Product
Transistor Tester
-
*Measure rich DC parameters of maniford semiconductors, e.g. diode, transistor, controlled silicon, FET.*Measure capacitor, varistor, DC voltage signal source*Measure 78 and 79 three terminal voltage regulator*Data hold, low battery warning*Complete with carry case and six 1.5V AA batteries
-
Product
IP VIDEO MARGIN TESTER
IPMT-3
-
The IPMT-3 is a precision attenuator used to test IP video systems to insure that you have an adequate digital signal margin. Digital signal margin is the amount of signal level above the digital cliff that you have in your system to prevent a picture failure from occurring. IP cameras will give you a perfect picture until the network cable loss reaches beyond the minimum allowable signal level and then you suddenly get no picture at all. This effect is called the digital cliff, because like walking off of a cliff, everything is great till you take the last step off the edge and then all is lost.
-
Product
LED Tester Software
Lumeresoft
-
Evolusys Technologies Sdn. Bhd.
At the heart of the software design philosophy is the ease to create test recipe amidst the dynamic range of LED packages design & test requirements. Whether it is a single die LED, multiple die LEDs, Chip-On-Board (COB) substrate, etc. the same software can be used off-the-shelf without any special customization.
-
Product
ADSL/ADSL2+ Tester
-
ST332B tester is a multi-functional and hand-held ADSL2+ test instrument with small size, specially designed for xDSL line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL etc) and maintenance.
-
Product
Automatic Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
Product
RCD & ELCB Testers
-
Shanghai Beha Electronics Co., Ltd.
*Ideal for tripping 3mA, 5mA, 10mA, 15mA, 20mA, 30mA, 50mA, 100mA, 150mA, 250mA, 300mA, 500mA RCDs*Accurate digital readout of disconnection time. *Timer Resolution 1ms (max time : 19.99s)*Zero crossing circuitry permit testing at 0° or 180°*Measure voltage between line and earth before testing.
-
Product
De-Energized Tester
MOTOR GENIE
-
The MOTOR GENIE® can see more than a megohmmeter, resistance tester, or RCL tester, making it the perfect tool for troubleshooting, startup, and quality control of low voltage AC induction motors.
-
Product
AMIDA IPM Tester
3001XP
-
HVI Source:16 Channels 4Q V/I Source; Two zero ref. floating GND ; ±30V, ±200mA Source ability; V/I read back at 16 bits resolutions under 100Ks sampling rate ; ±0.2% Accurate reading of Range
-
Product
Winding Resistance Tester
JYR-50C/40C/20C
-
1. With demagnetization function.2. Testing range reach to 20k3. Also apply to testing tranformer with high winding resistance.
-
Product
Digital LOOP/PSC/LOAD Tester
1825 LP
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures the voltage drop as if 16A was flowing between Line and Neutral.● Displays voltage without current (V at 0A).● Display voltage as if 16A flowing between Line and Neutral (V at 16A).● Loop test for L-E● PSC between L-N.● Single one smart push button operation; ON, Scroll through results and menus.● Checks wiring integrity (LEDs).● Auto off/auto ranging (software range).● Combined prospective short circuit current, loop and load tester.● Display can be customized for large orders.
-
Product
Multifunctional Scratch Hardness Tester
-
Sataton Instruments Technology CO., Ltd
Multifunctional scratch hardness tester is an integrated testing instrument designed for cross hatch cut method and five-finger (five arm) method to measure scratch or mar resistance, hardness, susceptibility of a material surface to different physical damage like scratching, marring, scraping, etc. The tester are made of two parts, one is for determination of resistance to scratches and cuts according to cross-cut test for paints and varinishes. The other is for
-
Product
AMIDA ATI 600 Tester
-
AMIDA ATI 600 Tester is a dedicated test system for semiconductor components (MOSFET, BJT, DIODE, ... etc.), which can accurately and quickly measure product parameters through form filling and editable program control. In practical applications, AMIDA ATI 600 Tester is the best choice for users, whether it is CP or FT mass production testing, or research projects of component characteristics.
-
Product
Solar Cell Tester
REOO RO-GTM2615
-
REOO RO-GTM2615 Solar Cell Tester is designed for PV cell manufacturing inspection, enabling fast cell performance inspection and stable electrical quality verification. Built for solar factories, it improves cell testing accuracy and maintains stable operation across PV cell production lines.
-
Product
Hand-held Cable Tester
STM-8
-
The STM-8 is an economical and versatile hand-held tester designed for the testing of UTP and screened cable for opens, shorts, reversals, miswires, split pairs and cable length.
-
Product
COMPUTER MONITOR TESTER
MT160
-
Test a wide variety of PC & Mac computer monitors-all in one unit. Extended scanning formats range from 15.7K to 80 KHz.
-
Product
Insulation Resistance Tester
UDH-50-1-T
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated•Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV •Resistance range to 1TΩ •Continuous digital display on LCM•Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
Product
Shore Hardness Tester
DRK201
-
Shandong Drick Instruments Co., Ltd.
The Shore hardness tester is applied to test the hardness of vulcanized rubber and plastic.
-
Product
Tube Tester / Tube Checker
RM 1
-
The RM 1 is a Vacuum Tube Tester easy to handle, in its construction almost unique, which enables a fast, simple and precise plate current measurement (emission test) of the most common double triodes (6SL7-GT, 12AT7=ECC81, 12AU7=ECC82, 12AX7=ECC83)¹ and power pentodes (6CA7=EL34, KT66, KT88, 6550, 6L6-GC, 5881, 6V6-GT, 6BQ5=EL84)¹. The device has a distinct classic design, primarily consisting of a solid beech wood cabinet and a front panel of anodized aluminium. Because of its small dimensions it is easily transported and it doesn't need a lot of space for accommodation.
