Starter Testers
See Also: Starter, Alternator Testers
-
-
Product
Voltage Continuity Testers
-
Built tough for use in industrial and commercial environments, measures voltage range up to 1000 V AC and 1200 V DC (2100-Gamma only). Designed with reinforced components for dependable performance.
-
Product
Earth Ground Tester
1625-2
-
The Fluke 1625-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1625-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps. This technique eliminates the dangerous, and time consuming job of disconnecting parallel grounds, and finding suitable locations for auxiliary ground stakes.
-
Product
Rail Pressure Tester
RPT-5
-
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
Product
Optical Length Testers
-
Optical Wavelength Laboratories
The BOLT and VOLT Optical Length Testers from OWL offer a unique, economical alternative to users who need to measure the length of optical fibers. Rather than purchase expensive certification test sets, the BOLT can be added to an installer’s existing fiber test kit for a fraction of the cost.
-
Product
Core Loss Tester
VCL
-
Core loss testing has become most important test for quality assurance in Electrical industry. Core loss tester determines that whether a Core is damaged or not.
-
Product
Capacitor Tester
MIG0603CAP
-
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
Product
Martindale Abrasion Tester
SG-P02M
-
This machine is ideal for determining the abrasion resistance of upper, lining, socking, and similar types of shoe materials, particularly those made of fabric. The specimens are capably tested for four bieces or six pieces(option) per time and are rubbed over the abrasive in all directions in a complex, repetitive pattern(a lissajous figure) and, at the same time, the holer totates.
-
Product
RF Device Tester
RF ITS
-
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
-
Product
Electric Testers / Multimeters
-
Electrical testing meters from Sper Scientific include our top quality digital multimeters, clamp meters and insulation testers. All Sper meters are designed for the highest levels quality, safety and reliability, with advanced features like True RMS and auto-ranging that add real value and functionality for everyday use.
-
Product
Motorcycle Battery Testers
-
ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.
-
Product
Portable Hardness Tester
-
Beijing TIME High Technology Ltd.
A compact, handheld device used for on-site measurement of a material's hardness.
-
Product
Line Testers
-
GAOTek provides a large collection of certified and feature-rich line testers for sale to the United States, Canada and Globally. These devices are mainly used for line installation, line performance testing, inspection, and maintenance of the telecommunication networks. They are particularly designed to accelerate telecom trouble shooting and with the help of latest technology they are equipped with a smart CPU, IC, and SMT. These devices have some unique features such as caller ID display and last number redial. Moreover, it can also be used for multi-line testing, wire pair checking, inspection of line insulation and test for breaks and faults.
-
Product
HV Tester
-
For High Voltage withstand, breakdown testing of electrical insulating systems.For Dielectric Strength testing of electrical / electronic components, small appliances, tools, motors, machines etc.
-
Product
Digital Deadweight Tester
PIT-5000
-
The PIT5000 is the modern tool for conducting pipeline hydrostatic tests. Replace your dead weight testers, pressure chart recorders and temperature chart recorders with the convenience of digital data collection and user friendly PC software. Pressure, ambient temperature and pipeline temperature are measured by the system's NIST traceable instrumentation and plotted on one graph versus time.
-
Product
NVIDIA® Jetson™ TX2-Based AI Smart Camera Starter Kit/Lite Kit
NEON-2000-JT2 Series Kit
-
- Integration of NVIDIA Jetson TX2, image sensor and vision software suites, ready to deploy- All-in-one design minimizes cabling, footprint and maintenance- FPGA base DI/O for accurate real-time triggering- Validated and comprehensive accessories, saves effort on surveying and debug- Pre-installed software and sample code, easy to get started- Two kit configurations to satisfy different applications
-
Product
DC Hi-Pot Tester
3010HP, 3025HP & 3050HP
-
The DC Hi-Pot test is an important part and parcel of the electrical safety tests mandated by standards organization world-wide. More than 80 per cent of faults in electrical and electronic systems are due to weak insulation caused by environmental factors such as dirt, grease, temperature stress, humidity, etc that affect the dielectric strength of the insulation material.
-
Product
Semiconductor Device Testers
-
are particularly suitable for certain semiconductor test requirements, but other models may also be of interest. Our knowledgeable application engineers can guide you to the most suitable model.
-
Product
Crease Recovery Tester
TF110
-
TESTEX Testing Equipment Systems Ltd.
Crease Recovery Tester, to determining recovery properties of fabrics by creasing in a loading device for a predetermined time using a weight suitable for the test method specified (BS/ISO/AATCC), After transferring the specimen to the clamp of the tester, the specimen is allowed to recover and the angle of recovery recorded. Fabric Crease Tester complies with ISO 2313, AATCC 66, BS EN 22313， etc.
-
Product
Electrical Tester
C.A 755
-
Lightweight and comfortable to handle, the C.A 755 is equipped with an IP 54 casing protected against dust and capable of withstanding falls from 2 metres. With its large 3,000-count backlit display, the C.A 755 tester is ergonomic and functional.
-
Product
WiGig RF Tester
IQgig-RF Model B
-
When used in conjunction with IQgig-IF, an optimized test solution for conducted testing of WiGig chipsets and baseband modules, the IQgig family products provide a total test solution for R&D characterization and high volume manufacturing.
-
Product
Hydrogen Leak Tester
T8999
-
T8999 is a tool designed to meet the increasing need for easy and clean identification of the position of the leak on a piece being tested, therefore eliminating the need for methods such as water tank immersion or use of leak detecting sprays, which are harmful for the pieces which could develop rust or pieces that are difficult to accurately clean.
-
Product
Automatic Battery Testers
-
T100BT is an innovative, modular battery testing equipment able to combine, on a single test platform, all the tests required to detect any possible defect on battery cells and modules: from defective cell wiring, to geometrical or surface irregularities, to out-of-specs performances.The battery tester is designed for the high-volume production test of battery modules composed by prismatic, cylindrical, or pouch cells, as well in a Lab/NPI version for engineering, prototypes and low-volume battery testing. The complete configurability allows you to equip the tester with the modules and tools you need to test your products, reaching the desired throughput.
-
Product
Electric Testers
-
ATEQ offers a broad range of electric testers designed to meet the diverse needs of various industries. These testers, including advanced battery testers, are pivotal in ensuring the efficiency and safety of electrical systems. They are used in applications ranging from automotive and e-mobility to broader industrial purposes and EV battery testing. ATEQ’s electric testers are known for their precision, featuring integrated databases for battery types and parameters, secure systems with comprehensive battery protections, and user-friendly interfaces. This makes them essential tools in production lines, research and development laboratories, and for EV/HEV expertise
-
Product
Respirator Fit Testers
-
Respirators and masks play a crucial role in protecting workers from various airborne hazards, including environmental and chemical dangers, as well as airborne biohazards, in the workplace.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
Scratch/Shear Tester
3025
-
The Elcometer 3025 Scratch/Shear Tester is used to test the resistance of many materials to scratching, shearing, gouging, marring, scraping and engraving.
-
Product
CT Admittance Tester
505B
-
Red Phase Instruments Australia Pty Ltd.
Field testing kWh meters is easy, field testing CTs when live is much more difficult. Our admittance tester can test CTs live with 50Hz or 60Hz current in the metering circuit. This technique does not confirm the accuracy of a CT but it will detect faults that give metering errors, such as shorted turns, metering circuits shorted to ground and tampering of CTs. CT faults can cause large revenue losses. Admittance testing only adds 10 minutes to a routine polyphase meter test, giving cheap insurance.
-
Product
Dissolution Testers
-
Dissolution testers have wide application in Pharmaceutical Industry, for detecting velocity and extent rate of dissolution i.e. solution formation from a dosage form like tablet, capsule, and ointment, etc. across manufacturing plants, research centres.
-
Product
Cable Testers
E445
-
Tests 3 pin XLR leads, 2 and 3-pole A-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
