Showing results: 9151 - 9165 of 10519 items found.
-
Model LGA-4000Z -
Teledyne Analytical Instruments
Teledyne’s LGA-4000Z series leverages the latest in Tunable Diode Laser Absorption Spectroscopy (TDLAS) to achieve an ultra-fast gas measurement in-line without resorting to extraction and sample conditioning. By tuning the laser to a specific absorption wavelength, based on the gas of interest, the attenuation of the light through a sample cell and the detector can be correlated to the concentration of each gas, per Beer-Lambert Law. The laser provides a narrow absorption band which minimizes the effect of interfering compounds in the process.
-
Model 6400T -
Teledyne Analytical Instruments
The 6400T Series analyzers uses a proven UV fluorescence principle coupled with state-of-the-art microprocessor technology to provide accurate and dependable measurements of low level SO2. The 6400T-H2S measures hydrogen sulfide (H2S) by incorporating a catalytic converter set at 600°F (315°C) to oxidize H2S into SO2 while leaving other more difficult to oxidize sulfurs unconverted. A switching mode allows analysis of both H2S and SO2 concurrently.
-
FXA-113 PSU Relay 4CH -
Konrad Technologies GmbH
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
3108 -
Metrel d.d.
MI 3108 EurotestPV is a combined photovoltaic tester and electrical installations safety tester. It enables complete testing of electrical installations according to EN 61557 standards and in addition performs all necessary tests required on single-phase photovoltaic (PV) installations. This includes all of the tests as required by EN 62446, but also includes I - U characteristic, Calculation of STC values as required by EN 61829 and power measurements on Inverter’s DC and AC sides.
-
MI 3152H EurotestXC 2,5 kV -
Metrel d.d.
MI 3152H EurotestXC 2,5 kV is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN and TT earthing systems expanded with insulation resistance measurement with the test voltage up to 2,5 kV are managed by a completely new user interface based on large colour touch screen display.
-
NanoScan -
mks Ophir
Measure your beam as never before with the NanoScan™ beam profiler. The advantage of scanning slit beam profiling is sub-micron precision for measuring beam position and size. Scan head configurations include Silicon, Germanium, and Pyroelectric versions for a wide range of wavelengths and laser power levels. The NanoScan software is available in two versions: Standard and Professional, and includes an extensive set of ISO quantitative measurements, an M2 Wizard, and the ability to measure laser power.
-
ARAMIS -
GOM GmbH
ARAMIS is a non-contact and material-independent measuring system based on digital image correlation (DIC). It offers a stable solution for full-field and point-based analyses of test objects of just a few millimeters up to structural components of several meters in size. The system performs high-precision measurements with a 3D image resolution in the submicrometer range, regardless of the specimen’s geometry and temperature. There is no need for a time-consuming and expensive preparation. For statically or dynamically loaded specimens and components, ARAMIS provides accurate
-
TOB-IT8512 -
Xiamen Tob New Energy Technology Co., Ltd
IT8512 120V/30A/300W DC Programmable Electronic Load for Battery and Power Supply TestHigh performance and affordable single channel DC electronic load. TOB-IT8512 DC electronic loads provide you with the flexibility to test a wide range of applications from power supply, charger to battery. The high resolution voltage(1mV), current(0.1mA) measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
IQgig-5G -
LitePoint Corporation
The IQgig-5G is a fully-integrated, non-signaling solution for testing 5G mmWave products at both the 28 GHz and 39 GHz frequency bands. All signal generation, analysis, and RF front-end routing hardware are self-contained inside a single chassis. The IQgig-5G is license-upgradeable to support the pre-5G and 3GPP standards evolution with up to 1 GHz of tester bandwidth. The IQgig-5G solution has three bi-directional source and measurement ports each with 2.92mm connector coaxial interface.
-
ADC-2555 -
TestVonics, Inc.
TestVonics ADC-2555 Air Data Calibrator is a high accuracy pitot static calibrator. The ADC-2555 is capable of controlling and measuring Altitude and Airspeed pressures with the highest degree of accuracy. The control and measurement range of the test system can meets or exceed requirements for both commercial and military applications. The ADC-2555 is a derivative of the ADC-2500 Series. It features a touchscreen interface, a mid range 23PSIA sensor and features TestVonics automated calibration software for the TTu-205J Pressure-Temperature Test Set.
-
CEMS100 -
Rohde & Schwarz GmbH & Co. KG
Setting up an EMS/EMI test system is a very complex process requiring significant investment. The steps involved include custom planning, design, installation and configuration of various components and standalone instruments as well as the RF shielded anechoic chamber. Rohde & Schwarz offers the standardized R&S®CEMS100 test platform that is the company's first flexible, reliable and cost-effective off-the-shelf solution for radiated EMS measurements in line with IEC/EN 61000-4-3.
-
ZET 7012-I VER.2 -
ZETLAB Company
ZET 7012-I VER.2 digital gauge pressure (open membrane) is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface. ZET 7012-I VER.2 digital gauge pressure (open membrane) is intended for integration into various technological processes automated control systems. Open membrane type enables sensors operation in viscous, pasty and rapidly polymerizing environments.
-
ZET 7112-I VER.2 -
ZETLAB Company
ZET 7112-I VER.2 digital gauge pressure (open membrane) is used for fast and simple pressure measurements and measured values data transfer in digital format via CAN 2.0 interface. ZET 7112-I VER.2 digital gauge pressure (open membrane) is intended for integration into various technological processes automated control systems. Open membrane type enables pressure meters operation in viscous, pasty and rapidly polymerizing environments.
-
Fieldpiece Instruments, Inc
The In-Duct Hot-Wire Anemometer & Psychrometer accessory head, AAT3 allows HVACR professionals to measure air velocity, temperature, and %RH all in one tool. The engineered 38" telescoping probe with laser etching and quick-response sensor provides quick and easy airflow measurements from the correct location--near the evaporator. When using with the Fieldpiece HVAC Guide System Analyzers, the AAT3 can automatically calculate target super heat and target evaporator exit temperature.
-
LXinstruments GmbH
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.The system has a Virginia Panel adapter interface to which various desk adapters can be docked, including automated contacting of the DUTs. A camera for the verification of light emitting diodes on the test object is integrated in the adapter interface.
