Showing results: 8896 - 8910 of 10567 items found.
-
831-LOWN -
Larson Davis, Inc.
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
-
58606 -
Chroma ATE Inc.
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
MDN8I -
Holding Informtest
MDN8I is a mezzanine module designed for high-precision measurements in dynamic signal analysis systems, as well as for joint work with ICP sensors and vibration transducers with a charge output (force sensors, dynamic pressure, acoustic emission, vibration displacement, etc.). The MDN8I mezzanine module has electrical characteristics no worse than those of most foreign and domestic counterparts, and in some parameters exceeds them.
-
Ferrites India
Ferrites India offers testing of materials for measurement of their magnetic properties. These materials are in the shape of laminations, stacks, solid toroids, laminated toroids, solid rods or magnets. The testing can be done under wide range of frequency and test specifications and various magnetic properties like B-H Curve, Loss, Permeability, Coersivity, Remnancy, Saturation Magnetization are measured. The testing is done as according with ASTIM/IEC/IS standards.
-
Apex Technologies
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
104-DIO-48E -
Acces I/O Products, Inc.
The circuits use an 82C55A PPI with mode 0 supported. Ports A, B and C are buffered with 74ABT245 transceivers and pulled up to 5V. The optional 82C54 has three-sixteen bit down-counters within one chip. These counters are useful for making frequency outputs, measuring frequency of square waves, pulse width outputs, pulse width measurements etc. Software drivers are provided on CD.
-
Texas Instruments
Ultrasonic sensing is the measurement of the time between an ultrasonic signal being sent and received. The interval between these two signals is typically referred to as time-of-flight (ToF) and depends on the distance the ultrasonic wave travels until it is reflected due to an impedance change and the speed of the ultrasonic wave. The basic equation time = distance / speed can be used to measure fluid level, fluid identification/concentration, flow, or proximity.
-
PROFITEST Series -
GMC-I Messtechnik GmbH
The instrument is capable of executing all measurements for testing the effectiveness of safety measures in electrical systems as required by VDE 0100, part 600, and as specified in the individual sections of VDE 0413. Consequently, it's ideally suited for approvals and periodic testing of stationary electrical installations. Thanks to measuring category CAT IV, the PROFITEST Master provides the user with highest possible safety levels.
-
SomatXR CX23-R -
HBM, Inc
The ultra-ruggedized SomatXR CX22B-R data recorder is intended for use in harsh environments and reliably stores measured data in applications such as vehicle tests. The recorder records data from other SomatXR modules using an Ethernet connection. At the same time, FireWire allows its use as a gateway for direct data transmission to the PC. Both centralized and distributed measurement systems can thus be implemented.
-
Rhein Tech Laboratories, Inc.
Rhein Tech Laboratories, Inc. (RTL) is a full-service design and compliance engineering test laboratory. We have grown with the industry from general purpose EMC testing into other areas of testing such as Radio (RF testing), Military and Aviation, Industrial, Scientific and Medical, Automotive, Electrical Safety, Shielding Effectiveness, Site Surveys and Radar Cross Section & High Range Resolution measurements.
-
AMIC-15k1 -
Amperis sl
*The partial discharge indicator PDI.*Diagnosis of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD*Allows to test the electrical durability of the tested object - indication of breaking voltage.*The high resistance to electromagnetic interference ensures uninterrupted operation in power plants and near high-voltage transmission lines up to 1200 kV AC and 500 kV DC.
-
NI
LabVIEW is engineering software designed specifically for test, measurement, and control applications that require rapid access to hardware and data insights. The LabVIEW Full Development System is recommended to customize your engineering application with advanced inline analysis and control algorithms. For applications that require software engineering tools to develop, debug, and deploy professional applications, consider LabVIEW Professional Development System.
-
ProDAQ 3080 -
Bustec Ltd.
The ProDAQ 3080 VXIbus Gigabit Ethernet slot-0 interface provides access to VXIbus instruments through a standard Gigabit Ethernet interface using the VXI-11 protocol. It is designed to function as a bridge between the established, time-tested, proven base of VXIbus instruments and the Ethernet, allowing users to build any size of test and measurement system simply by connecting the instruments via standard LAN to a computer.
-
MPX-SR3 -
Arden Photonics LTD
Arden’s MPX Modal Explorer makes measurement of Encircled Flux easy, and accurate, and it complies with international standards. But if you are measuring laser-based transmission light sources for multimode systems you may need to use a test jumper assembly and fiber shaker in order to avoid “speckle”. Industry standards (for example IEEE 802.3aq and FOTP– 203) call for the use of a mechanical fiber shaker.
-
Electroacoustics Toolbox -
Faber Acoustical, LLC
Electroacoustics Toolbox is a modularized, multi-channel dynamic signal analyzer and data acquisition platform for Mac. It brings powerful new tools to the Macintosh platform for multi-channel, audio-band data acquisition and real-time analysis of electrical, acoustical, and electroacoustic signals and systems. It enables precise measurements of acoustic quantities, such as equivalent and time-weighted sound levels, as well as acoustic and electroacoustic systems, such as listening rooms and loudspeakers.
