Showing results: 7666 - 7680 of 10562 items found.
-
MFC2046 -
Metrolab Technology SA
MRI and NMR spectroscopy applications require a highly uniform magnetic field, within at most a few ppm. NMR is the only magnetic measurement technique capable of providing a field map with that degree of precision. Introduced 25 years ago, Metrolab’s NMR Magnetic Field Cameras have revolutionized field mapping for MRI magnets. They reduced acquisition times from hours to minutes, positioning errors to fractions of a millimeter, and they rendered human and drift errors negligible. Now, meet the latest generation NMR Magnetic Field Camera, the MFC2046! Map any magnet with the New generation of MFC probe arrays. Magnetometer Teslameter Gaussmeter
-
Process Insights, Inc.
Our real-time Extrel quadrupole mass spectrometers are built for the demands of the gas and ion analysis for industrial and high purity process control, environmental monitoring, and cutting-edge laboratory research. Our mass spectrometers offer high sensitivity and a wide dynamic measurement range (ppb to %) for full, speciated composition. Our fast and powerful, quadrupole mass spectrometer performs precision quantitative analysis on every component in a gas or vapor mixture. It can easily be fully automated for sampling of multiple gas channels. For decades we have collaborated with research, academic, and industrial customers to deliver, design, integrate validate, and support these unique turnkey solutions.
-
Flex One -
ZOLIX
Photoluminescence (PL) is the light emission from a material under the excitation by ultraviolet, visible or near infrared radiation. In semiconductor luminescent property measurements, the sample (e.g. GaN, ZnO, GaAs etc.) was usually excited by a laser (with a wavelength of 325 nm, 532 nm, 785 nm etc.), and its PL spectrum is measured to analyze the optical physical properties, such as the band gap width etc.. Photoluminescence is a high sensitivity, non-destructive analysis method, which can provide the information about the structure, composition and surrounding atomic arrangement of materials. Therefore, it is widely used in physics, materials science, chemistry and molecular biology and other related fields.
-
A994 -
AGM Elettronica
The A994 is an open circuit locator for electric and telephone cables wind on the reel; it gives the position of the fault from the inside or outside end of the cable, in percentage to the total cable length. The instrument measures the ratio of the capacitances of the two sections of failed conductor using two high precision i/v converters. The advantage of this method is due to the fact that the measurement error depends almost exclusively on the dimensional inhomogeneity of the cable. The A994 has the unique feature to permit the location of fault in cables with all broken wires. This instrument locates breaks in cables with a total capacity between 2 nF and 5 uF. The distance to fault is displayed on a large LCD display.
-
Saluki Technology Inc.
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
Model T200U -
Teledyne Advanced Pollution Instrumentation
The Model T200U Trace-level NO/NO2/NOx analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is designed to allow ultra-sensitive measurements with a lower detectable limit of 50 ppt while still meeting the requirements for use as a US EPA compliance analyzer.The Model T200U combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer.
-
ams AG
The biometric sensors product family features first-of-its-kind integrated optical sensor modules which include algorithms for heart-rate measurement, photoplethysmography (PPG) and electrocardiography (ECG). The modules are ideal for a wide range of end products including wearable devices, medical monitors, industrial equipment and mobile devices. Biometric sensors from ams are able to achieve the highest accuracy ratings in the industry because of a combination of a low-noise analog and optical front-end and custom ams software and algorithms. Drawing on expertise in optical sensing in mobile devices, ams provides OEMs with electrical, mechanical and optical design guidelines to enable designers to quickly realize a successful
-
EL63150B -
MCH Instruments Co.,Ltd.
Features:*Number operation and control*LED display with high definition and high contrast, rich display information*Easy operation of knob encoder switch*Basic load function: constant current, voltage, power and resistance*Multi units used to multiple load ability*Short-circuit test*Battery test*Dynamic test*Multi parameters measured in the list*Remote voltage measurement*Panel and exterior trigger function*Protection function: over-voltage, over-current, over-power, over-heat, polarity connection in reverse*10 sets of parameters memorized and loaded, and automatically loaded on turning on the instrument*Intelligent fan control*Key lock and knob lock functions
-
ProDAQ 5821 -
Bustec Ltd.
The ProDAQ 5821 series of Signal Conditioning Cards is designed to interface with a variety of sensors, principally RTDs, Thermistors, Cryogenic Diodes and Voltage type sensors. Each version of the 5821 provides the capability of precise 4-wire measurement. In order to achieve this, a precise 500μA constant current source is provided per channel. The current source can be disabled on a per channel basis and is monitored to ensure that current is flowing. The value of the output current is stored on-board after calibration. In order to achieve the highest accuracy the output current may be automatically calibrated 'on-the-fly' using the ProDAQ 3416 24-bit Sigma-Delta ADC card and an on-board precision resistor.
-
CFD200 -
TEAM SOLUTIONS, INC.
The CFD200 is a new concept in test equipment that allows a PDA, laptop or tablet PC to be turned into a dual channel Digital MultiMeter with sophisticated analysis capabilities. SmartAnalysis software facilitates step-by-step fault investigation with instant display of results and an interactive diagnostic guide. With the CFD200 it is possible to integrate multiple measurement functions into a single hardware/software platform, providing high-level analysis features and a small, lightweight and portable unit. The CFD200 is an extended Compact Flash design offering two channels with full galvanic isolation to host and channel-to-channel. Each offers a scope function up to 40KSPS with full datalogging capability and 650V max. input voltage.
-
EL3630B -
MCH Instruments Co.,Ltd.
Features:*Number operation and control*LED display with high definition and high contrast, rich display information*Easy operation of knob encoder switch*Basic load function: constant current, voltage, power and resistance*Multi units used to multiple load ability*Short-circuit test*Battery test*Dynamic test*Multi parameters measured in the list*Remote voltage measurement*Panel and exterior trigger function*Protection function: over-voltage, over-current, over-power, over-heat, polarity connection in reverse*10 sets of parameters memorized and loaded, and automatically loaded on turning on the instrument*Intelligent fan control*Key lock and knob lock functions
-
M+P International
Noise is increasingly the subject of new regulations for the protection of human health and safety as well as for improving the environment in general. As well as sound levels, the perceived sound quality of products from washing machines to vehicles is often an important part of the customer buying decision so must be considered during product development. m+p Analyzer for noise and vibration measurement and analysis provides a full range of capability for these applications. Real-time fractional octave filters satisfy all acoustic applications from simple sound pressure, sound power for equipment legislative requirements, intensity mapping to isolate sources to sound quality metrics for product refinement.
-
FLIR E96 -
Teledyne FLIR
The FLIR E96 is our first pistol-grip camera with 640 × 480 thermal resolution so inspectors can survey high-voltage, hazardous targets safely and quickly diagnose electrical and mechanical failures. Interchangeable AutoCal™ lenses offer complete coverage of near and distant targets, with the laser distance meter ensuring the crisp focus needed for accurate temperature measurement. The onboard FLIR Inspection Route runs pre-planned routes to help inspectors stay organized when surveying large or multiple locations. FLIR Ignite provides automatic uploading of E96 images directly from the camera to the cloud for easy, secure storage and sharing.
-
72-8345A -
Tenma
Switch Mode Laboratory DC Power Supplies Precision adjustable supply provides adjustable 1~36VDC output with adjustable current limiting from 0~3A. It is ideal for test, measurement and service applications where tight voltage and current regulation are critical. Highly efficient switch mode design delivers outstanding performance from an extremely compact footprint. Unique separate output ON/OFF control allows voltage and current setting, with the supply output turned off. Part of a Complete Series, this slim supply occupies little bench space while providing very high precision and 90W of continuous output.
-
Premier Electrosystems
Premier Electrosystems' Standing Loss System is used to calculate the energy consumption measurement of a filled water heater, after steady state conditions have been reached when connected to electrical supply and when no water is drawn for a minimum of 48 hours.The star rating for the electric geysers is given based on the standing losses. Standing loss or heat/energy loss of a water heater to the surrounding in 48 hours is an important factor used by BEE (Bureau of Energy Efficiency) to decide on star rating of a water heater. The unit of Standing Loss is Energy consumed per 24 hrs for a difference of 45 ° C (kWh/24 hrs/ 45 ° C).
