Modulation Meters
Meters that measure the process, or result of the process, of varying a characteristic of a carrier, in accordance with an information-bearing signal. (atis.org)
See Also: Modulation, Optical Modulation, Modulation Analysis, Modulation Analyzers, MER
-
Product
PXI Analog Output Module
Analog Output Module
PXI Analog Output Modules support both static and software-timed voltage output applications. Modules also include 5 V TTL/CMOS digital I/O lines. Some PXI Analog Output Modules can deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. These advanced features enable you to use the PXI Analog Output Module to replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, SMB
40-835A-001
Multiplexer Module
The 40-835A-001 (PXI) and 42-835A-001 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
PXI BRIC8 1Resource Distributor, 6Bus Matrix
40-569-116
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
PXI 8 Slot BRIC 150x16 2-pole (10 sub-cards)
40-561A-122-150X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 2.5Ω to 472Ω
40-298-120
Programmable Resistor Modules
The 40-298-120 is a high density programmable resistor module with 4 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm
50-294-013
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-025
Programmable Resistor Modules
The 40-254-025 (PXI) and 42-254-025 (PXIe) are programmable resistor modules with 1 channel which can be set between 1.5Ω and 13.6kΩ with 4Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Multiplexer 2:1 With De-Emphasis 32 Gb/s
M8062A
Multiplexer Module
R&D and test engineers who need to characterize serial interfaces of up to 32.0 Gb/s can use the M8061A 2:1 Multiplexer with optional de-emphasis to extend the rate of J-BERT M8020A and J-BERT N4903B pattern generator. For the most accurate receiver characterization results, the M8061A provides four calibrated de-emphasis taps, which can be extended to eight taps, built-in superposition of level interference and Clock/2 jitter injection. The M8061A is a 2-slot AXIe module that can be controlled via USB from the user interface of J-BERT M8020A as well as N4903B.
-
Product
Regular Flex I/O For Reset, Remote Switch And 5VDC
98R17500801
Expansion Module
Flex I/O expansion on the front panel for same-side cablingCompatible with MIC-7300, MIC-7500, MIC-7700, MIC-770, MIC-7900
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 480 Position, Unloaded
510151106
ITA Module
NOTE: Part # 510151106 Rev E and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150116. (May mate with other Receiver modules, as well.)
-
Product
PXI BRIC4 FIBO Matrix Dual 62x4 2pin brkout
40-592A-012
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 18 GHz, 50 Ω, SMA, Failsafe
40-788-121
Multiplexer Module
The 40-788-121 (PXI) and 42-788-121 (PXIe) are single failsafe SP10T 18 GHz unterminated microwave multiplexers. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
Product
Mini Power/Mini Coax, Module, Receiver, iCon Series, 24 Position
510160104
Receiver Module
Primary mating module 510161104. (May mate with other ITA modules, as well.)
-
Product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 50Ω, MCX
42-877A-101
Matrix Switch Module
The 40-877A-101 (PXI) and 42-877A-101 (PXIe) are 50Ω 2x2 RF matrices with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI 64x4 Matrix Module, 2-Pole, 2A, 60W
40-583-001
Matrix Switch Module
The 40-583 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 64x4 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 160 pin DIN 41612 connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
Product
PXI 3A Power MUX BRIC, 8-Channel, 12-Pole
40-571-302
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-10/8
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-042
Programmable Resistor Modules
The 40-297A-042 (PXI) and the 42-297A-042 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 395 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
LXI Microwave Matrix, 10GHz, Single 3x3
60-750-133
Matrix Switch Module
The 60-750-133 is a single 3x3 10GHz microwave matrix. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 20GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
PXI 8-Slot BRIC Matrix, 184x8, 1-Pole (4 sub-cards) Dual Bus
40-560B-121-184X8-M
Matrix Switch Module
The 40-560B-121-184x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
Product
PXI 8-slot BRIC Matrix, 2A, 2-Pole, 456x4, 8 Sub-cards
40-574-108
Matrix Switch Module
The 40-574-108 is a 456x4 2-pole matrix and is part of a range of BRIC matrices providing high density configurations capable of switching signals up to 2 A. The modules are available in 2, 4 or 8-slot PXI sizes and are constructed using high quality electro-mechanical relays.
-
Product
PXI 3x3 20GHz Matrix with Termination
40-787-528-3X3-T
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
PXI Analog Output/Current Loop Simulator Module - 12 Channel
41-765-002
Analog Output Module
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
Matrix Switch Module
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 239Ω
40-252-013
Programmable Resistor Modules
The 40-252-013 is a programmable resistor module with 4 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Precision Resistor Module, 9-Channel, 2 to 6.97k
40-297-030
Programmable Resistor Modules
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI 4-Channel Precision Resistor Card
50-297-102
Precision Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω SMB
42-729A-001
Matrix Switch Module
The 40-729A-001 (PXI) and 42-729A-001 (PXIe) are 8x4 50 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI Multiplexer, 16-Bank, 5-Channel, 1-Pole
40-616A-021-16/5/1
Multiplexer Module
The 40-616 16-Bank, 5-Channel, 1-Pole Multiplexer Module is part of our range of reed-relay based switching solutions. The Module consists of 16 electrically isolated banks of multiplexers controlled by a PXI/ PCI interface. Each bank is a 1 to 5 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously.
-
Product
PXI 8-slot BRIC Power Multiplexer, 48-Channel, 6-Pole (8 Sub-cards)
40-571A-406
Multiplexer Module
The 40-571A-406 is a 48-channel, 6-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
