Radiation
The transmission of energy through material or space.
-
Product
Comb Generator
RefRad X
-
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
Product
Antenna, Octave Band Horn
EM-7020 | 1 GHz – 2.5 GHz
-
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
Product
Three Loop Antenna
VVLA-30M
-
The three loop antenna VVLA-30M is a standard measurement antenna according to CISPR15-2005/GB17743-2007 standard
, it can work with LISUN EMI-9KA / EMI- 9KB EMI Receiver System for EUT magnetic field radiation measurement between X, Y and Z planes. The antenna measurement is accurate, switch conveniently and it can completely replace imported products. -
Product
EMS Test System
TS9982
-
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
Horn/Notch Antennas
-
Horn and Notch Antennas perform well over wide bandwidths while providing directive radiation patterns and moderate gain levels. CAES offers an extensive range of products including conical, pyramidal and sectoral horn antennas, as well as dual-polarized, high-power tapered notch antennas.
-
Product
370MHz To 6GHz Radiation Measurement System
RMS-0460
-
The MegiQ Radiation Measurement System (RMS) is a compact test system that performs 3-axis radiation pattern measurement in non-anechoic spaces.
-
Product
Precision Conical Dipole
PCD 3100
-
Site validation measurements according to prEN 50147-3 in fully anechoic rooms. Accurate RF radiation safety measurements (e.g. broadcast stations). All purposes of broadband precision field-strength measurements. Frequency range: 30 MHz - 1 GHz
-
Product
EMC Testing Services
-
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
Product
Real-time X-ray Medical Device Inspection System
The Bench-X
-
Our latest real-time, compact system used for Medical Device X-ray Inspection. Very configurable and compact with high resolution at relatively low radiation levels.
-
Product
UV systems / UV systems / UV devices
-
The LightGuide pureUV is a UV radiator part, which prevents direct radiation to the substrate as far as possible.
-
Product
3 AXIS DIGITAL ELF 50/60Hz AC GAUSSMETER, FWBELL
4100 Series
-
Integrity Design and Reseach Corp.
Typical Applications include checking the 50 and 60 Hz magnetic fields (EMF) produced by equipments such as AC Power Lines, Office Equipment, Video Display Terminals, Household Appliances, home and Building Inspection, etc.. Magnetic fields are invisible radiations, the best method to measure the strength fields is to use one of the accurate gauss meters offer by Integrity Design & Research corp.
-
Product
Solar Radiation Sensors
-
The solar radiation sensors that Campbell Scientific offers come in a variety of designs: pyranometers, net radiometers, quantum sensors, and pyrheliometers. These sensors measure various aspects of the energy imparted by the sun on the Earth’s surface. A leveling fixture fitted with a bubble level may be required to accurately install solar radiation sensors.
-
Product
Omni-Directional Radiation Pattern, Compatible For WiFi5/6/6E/7, Industrial Grade Temperature Range
AIW-512-I
-
Dipole antenna with omni-directional radiation patternSupport 6GHz bandCompatible for WiFi5/6/6E/7RP-SMA male connectorOperating Temperature: -40 ~ 85℃
-
Product
Non-Linear Junction Detector
ORION™ HGO-4000
-
The ORION HGO-4000 is REI’s original high gain Non-Linear Junction Detector for special applications. The ORION HGO-4000 can locate listening devices and semiconductors in walls floors, ceilings, fixtures, furniture or containers and provides a user the capability to detect hidden electronic devices, regardless of whether the device is radiating, hard wired, or even turned off.
-
Product
Radiating Comb Generators
TBCG1
-
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
Product
Air Temperature Probe
TP32MTT.03.C
-
Probe for air temperature - protective shield from solar radiations.
-
Product
Calibration
EMC Test Antennas
-
There are some changes in the calibration standard ANSI C63.4 concerning the calibration procedures of hybrid antennas, also the newly issued standard - CISPR 16-1-6 dealing with EMC antenna calibration is covered by our services. You are very welcome to consult Seibersdorf Laboratories calibration experts for the recommended calibration procedures of the most common radiated emission test standards.
-
Product
EMI/EMC Testing
-
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
Product
OEM 1-Channel Fiber Optic Signal Conditioner PCB Module
FOTEMP1-OEM-MNT
-
The FOTEMP1-OEM-MNT is a small form factor PCB interface module designed for low cost insertion of high precision GaAs-based fiber optic temperature sensor technology into OEM applications where common electrical temperature sensors and thermocouples cannot be used. The OEM interface product is compatible with all TS series fiber optic temperature probes. The sensors are entirely non-metallic and electrically passive, providing immunity to EMI, RFI, MR, microwaves and radiation is required.
-
Product
Single Event Effects Test System
SEE-RAD
-
The SEE-RAD test system brings together the proven features of our ETS780 tester (such as true APG memory test and powerful FA tools) with the newest technology of the Griffin III. With all new high-accuracy DC Parametrics, superior precision pin drivers, and capture memory of 64M, the Griffin SEE-RAD combines the newest innovations in the test industry with our years of experience in Radiation Test.
-
Product
Pyroelectric Infrared Sensors
-
Panasonic Automotive & Industrial Systems Europe GmbH
Passive infrared motion sensors for detecting radiation changes in the infrared range.
-
Product
Non-Linear Junction Detector
ORION™ 900 HX
-
The ORION 900 HX Non-Linear Junction Detector (NLJD) detects electronic semi-conductor components through dense materials such as bricks, concrete, and soil. The ORION 900 HX NLJD is made to detect and locate hidden cameras, microphones, and other electronic devices regardless of whether the surveillance device is radiating, hard wired, or turned off.
-
Product
K-Band Silicon SATCOM Rx Quad Core IC
AWS-0102
-
The AWS-0102 is a highly integrated silicon quad core IC intended for satellite communications applications. The device supports four dual polarization radiating elements with full programmable polarization flexibility. The device provides 22 dB of gain with a noise figure of 3.4 dB. Additional features include gain compensation over temperature and temperature reporting. The chip features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
Product
EMI Tester
-
The EMI tester automatically measures the noise distribution of the electric field and the magnetic field radiated from electronic equipment with high accuracy.・ Even if PCB and IC parts have complicated bumpy shape and surface. The movable assembly can automatically trace them.・ EMI noise distribution is expressed as a variety of maps, such as 4D/3D/2D graphics and cross section view.
-
Product
UV Radiometers
-
A UV meter is used when the effect of UV radiation on a biological or chemical process, or the negative or positive effect of UV radiation on human health, needs to be quantified and documented.
-
Product
Motor and Resolver Control
-
With excellent radiation tolerance and enhanced performance, CAES’ Motor and Resolver Control products are ideal for moving you through space and other harsh environments.
-
Product
Optical Radiation Safety Test
EN62471-C
-
IEC62471-2006(CIE S009) Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
Product
NR01 net radiometer
-
Hukseflux Thermal Sensors B.V.
NR01 is a market leading 4-component net radiation sensor, mostly used in scientific-grade energy balance and surface flux studies. It offers 4 separate measurements of solar and longwave radiation, facing both up and down. NR01 owes its popularity to its excellent price / performance ratio and major improvements relative to comparable instruments. These advantages include weight, ease of levelling, solar offsets in the longwave measurement and pyrgeometer heating, reducing measurement errors caused by dew deposition.
-
Product
Fiber optic thermometer systems
TS Series
-
Micronor now offers a complete range of fiber optic temperature sensors, probes and interfaces for temperature measurement in challenging environments. TS series fiber optic temperature probes offer immunity to RF and microwave radiation along with wide temperature range, intrinsic safety and non-invasive use. The fiber optic temperature probes can operate over -200°C to +300°C (-328°F to +572°C), and withstand harsh and corrosive environments. Typical fiber optic temperature monitoring applications include:
-
Product
Wireless/RF Testing
-
NCEE’s experienced iNarte EMC/EMI qualified staff provide wireless and radio frequency (RF) testing of intentional radiators to ensure they meet the FCC, CE, and many other international regulatory requirements for transmitting and receiving (radio) devices. Frequent regulatory changes and complex testing requirements are common with wireless/RF equipment. NCEE Labs stays current with the most recent requirements and can help you navigate your requirements while supplying quality testing services to demonstrate worldwide compliance!
