Showing results: 1066 - 1080 of 1629 items found.
-
Broadcom Limited
Available in PCIe NIC and OCP mezzanine 2.0 and 3.0 form factors, Broadcom’s Ethernet network adapters support configurations ranging from 1G to 200G, and utilizing both optical and copper connectivity.
-
DP8000 -
Guzik Technical Enterprises
Guzik DP8000 Fiber Optics to PCIe® bridge / FPGA Accelerator Card, enables evolving markets such as High-speed Data-acquisition, High Performance Computing to take advantage of the latest Optics and DDR4 technology. The card provides up-to 24 bi-directional optical links with total user data bandwidth greater than 40 GB/s (320 Gbps) through the Samtec FireFly™ protocol-agnostic embedded optical engines.
-
FMC667 -
Sundance Multiprocessor Technology Ltd.
The FMC667 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6678 device. The FMC667 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier.
-
NES-FMCSER -
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
FMC1831 -
Sundance Multiprocessor Technology Ltd.
The FMC1831 is an FMC module designed to be compatible with AMC, VPX, PCI, PCIe, CompactPCI and PC/104 carriers. The module has two dual channel AD9361 transceivers with a maximum sampling frequency of 122.8 MHz over a bandwidth of 200 KHz to 56 MHz. A reference clock can be either externally supplied or be generated from an internal PLL. All input and output signals are connected via SSMC connectors for secure connectivity and signal integrity.
-
UTC003 -
Vadatech Inc
The VadaTech UTC003 is the most feature-rich MCH (MicroTCA Carrier Hub) for the Conduction Cooled μTCA chassis in the market. It’s management software is based on VadaTech’s proven Carrier Manager and Shelf Manager. The MCMC manages the power modules, the two CU (Cooling Units) and up to 12 AMCs within the μTCA chassis. It also interfaces to and manages the on-board fabric interfaces. The module is available with PCIe, SRIO, 10GbE Layer 3 managed, and GbE Layer 2 managed. The UTC003 runs Linux 2.6 on it’s MCMC CPU and is hot-swappable and fully redundant when used in conjunction with a second instance of the module. The firmware is HPM.1 compliant which allows for ease of upgrade. The UTC003 provides Fabric (100 Mhz HCSL) clock to each AMC.
-
TMPE633 -
TEWS Technologies GmbH
The TMPE633-10R provides 26 ESD-protected 5V-tolerant TTL lines, the TMPE633-11R provides 13 differential I/O lines using EIA 422 / EIA 485 compatible, ESD-protected line transceivers and the TMPE633-12R provides 13 differential I/O lines using Multipoint-LVDS Transceiver.
-
FastX-UXGA -
Alacron
The FastX-UXGA frame grabber series is for users who anticipate a demand for extreme I/O requirements or higher bandwidth, complex image processing and real-time fast storage in a cost effective platform. The base Fast-UXGA, is a raw-length PCI board with two (four-muxed) UXGA analog conversion channels using Analog Device's AD9888. The front end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, from zero to four PNX1702 processors before output. Finally, the Fast-UXGA interfaces to the host computer through a 4x PCIe interface for state-of-the-art data acquisition.
-
FastXe2 -
Alacron
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
FastX-APU -
Alacron
The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.
-
FastX3 -
Alacron
The FastX3 frame grabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX3, is a one half-length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. The front-end data is formatted and preprocessed by an Artix FPGA beforie being sent to the PCIe (X4) Gen 2 interface. It also is POCL and has isolated inputs including three LVDS I/Os.
-
VPX703 -
Vadatech Inc
The VPX703 is a Processor VPX (PrVPX) in 3U form factor based on the Freescale QorIQ T4241 or T4161 in a single-module. The PrVPX has 64 GB of onboard flash for storage. The module routes standard I/O such as SATA, USB, GPIO, RS232, etc. to the P1 connector.
-
DTA-2160 -
DekTec Digital Video B.V.
DekTec's Gigabit Ethernet adapter with three ASI/SDI ports, allowing zero-jitter transmission and reception of Transport Streams over IP networks; the additional three ASI ports allow easy conversion between the two interface types.
-
DTA-2180 -
DekTec Digital Video B.V.
A low-latency audio/video encoder taking zero CPU cycles. Ideal for compressing an HD-SDI signal, or for converting the PC's desktop to H.264 or MPEG-2 Video.The hardware is based on field-proven Magnum encoding technology.
-
DTA-2175 -
DekTec Digital Video B.V.
A general-purpose HD-SDI input and output, both ASI capable. A relay automatically connects input port to output port upon software- or hardware failures, enabling highly-available system configurations without requiring a failover switch.