Product

Rack Module with Standard Contactors with Anti-Harmonic Filters

MODF Rack

-

Lifasa - International Capacitors, SA

MODF Rack - Lifasa - International Capacitors, SA

The MODF-RACK control units include, in a compact form, all the components necessary for the operation of a step of a capacitor bank with filters. MODF-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.

Product

Standard Digital Multimeter - Auto Ranging

MM39

-

Martindale Electric Co. Ltd

MM39 - Martindale Electric Co. Ltd

The MM39 is an auto-ranging multimeter with a large rotary switch for easy selection of the required test, even when wearing gloves. There are two test buttons, one to lock the range and the other to hold the results which are displayed on a 3½ digit LCD screen.

The main test functions are AC voltage and DC voltage and current and resistance. The MM39 measures both AC and DC voltage between 0.1mV to 600V and AC and DC current between 10mA to 10A. There is a diode test and an audible continuity test which sounds at less than 25Ω.

Product

Real Time Monitor Interface

ANALYSIS 4N

-

ZOGLAB Microsystem Co., Ltd.

ANALYSIS 4N - ZOGLAB Microsystem Co., Ltd.

It supports a management on the on-site equipment, such as to add subnets, to add subnet equipment, or to config equipment parameters, etc. Subnet fulfills the following applications: parallel communication, interaction with equipment, batch logging, downloading, configuration, ending, timing synchronization and system status viewing.

Product

Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe

LFRE-1V-4

-

ECT

LFRE-1V-4 - ECT

Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

Standard Memory Grypper Sockets

-

Ironwood Electronics

Ironwood Electronics

Standard Memory Grypper Sockets

Product

Rubidium Standard with Optional DDS Signal Generator

1450B

-

Novatech Instruments , Inc.

1450B - Novatech Instruments , Inc.

The 1450B outputs can be configured as sine waves or square waves and can provide frequencies of 10MHz, 1MHz, 100kHz, 1pps or optional signal generator outputs. The signal generator outputs use direct digital synthesizer (DDS) technology and are confirurable from 100Hz to 171MHz. The 1450B also includes a 1pps input that can be used to discipline and automatically calibrate the 1450B. The 1pps input signal is typically obtained from an external device like a GPS frequency receiver/antenna. The Novatech GPS1 Smart Antenna with 1pps output is available as an accessory to provide a complete turnkey solution.

Product

Individual UPC Bar Code Standards

-

Applied Image, Inc.

Applied Image, Inc.

The UPC Verification Calibration standards are a unique set of symbols that assures an exact and reliable primary bar code standard exists for UPC codes based on ANSI X3.182/ISO 15416 methodology. These standards assures that manufactures of verification equipment, scanners, QC labs and end users now have an accurate basis for checking the measurement capabilities of their equipment. These standards are intended as a fundamental calibration tool for an QC program, providing a continuous scale from best to worse case characteristics of each parameter. With complete NIST traceable data supplied, it is ideally suited to those requiring traceability, such as ISO certification. Each symbol is individually calibrated to ANSI X3.182/ISO 15416 standards using a custom built microdensitometer. These cards are supplied calibrated for use with a 6 mil scan aperture and 660nm wavelength. (calibration wit other aperture sizes or wavelengths is available)

Product

Standard IR Target Projectors

-

Santa Barbara Infrared, Inc.

Santa Barbara Infrared, Inc.

Santa Barbara Infrared’s 14000Zi Series reflective infrared target projectors are turnkey test systems for electro-optical (E-O) testing of FLIRs and other infrared (IR) imaging systems. The standard target projectors are assembled from SBIR’s STC Series Collimators, Infinity Blackbodies and 300 Series Target Wheels. SBIR also offers a standard athermal target projector with a 5.7° field of view (FOV).

Product

Automatic Battery with Filters with Standard Contactors

BATLVF400

-

Lifasa - International Capacitors, SA

BATLVF400 - Lifasa - International Capacitors, SA

LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations

Product

Standard 1.08 (31.00) - 4.00 (114.00) Long Travel Bead Probe

BPLT-25C-4

-

ECT

BPLT-25C-4 - ECT

Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm

Product

Time Sensitive Networking Evaluation-Kit

-

Fraunhofer IPM

Fraunhofer IPM

The evaluation kit offers developers the possibility to test and evaluate Ethernet TSN for their own applications. It consists of either a Smartzync board (Xilinx) or a Netleap board (Intel/Altera) with an optionally implemented IPMS TSN-IP core for endpoint applications (TSN-EP), switched endpoint applications (TSN-SE) or switch applications (TSN- SW). Linux drivers with application examples, as well as RTOS test applications and TSN network configuration examples are also available.

Product

ACCUplace Macro Calibration Standard

AP-M Series

-

Applied Image, Inc.

AP-M Series - Applied Image, Inc.

With both X & Y axis metric scales, these dual axis targets are ideal for calibrating optical magnification in microscopes, linear distance, stage motion and squareness. In addition, with the larger area calibration scale, the calibration of low power optical systems over the longer distances can be easily carried out. The AP-M is offered on two standard materials; Glass (CG) and Opal (OP).

Product

Rack-Mounted Timing Systems

CommSync II Family

-

FEI-Zyfer Inc.

CommSync II Family - FEI-Zyfer Inc.

The CommSync II family of modular systems provide GPS time and frequency outputs to meet your synchronization requirements. All systems include support for multiple input and output modules including 1PPS, IRIG, HAVE QUICK, PTTI, IEEE-1588 PTPv2, low phase noise 1, 5, and 10 MHz sine wave as well as custom outputs.These systems are available with military SAASM MPE-S GB-GRAM, SAASM Force 22E MRU or civilian C/A GPS receivers. Rubidium or OCXO oscillators provide for excellent holdover performance in the event of failure of the reference inputs. In addition, they may be configured as Distribution Time and Frequency (DTF) systems that are synchronized by an external reference. Dual Redundant systems (CommSync II & CommSync II-D) may be configured with two GPS Time & Frequency (GTF) modules and two power supply modules (AC and/or DC power) for redundancy with uninterrupted automatic switchover.