Oscilloscopes
Analyze waveforms of electronic signals by producing a trace on a display screen of corrosponding oscillations of voltage and current.
See Also: Scopes, Fiberscopes, Microscopes, Borescopes, Endoscopes, Stethoscopes, Stroboscopes, Synchroscopes, Telescopes, Vectorscopes, Analog Oscilloscopes, Digital Storage Oscilloscopes, Oscilloscope Probes, Waveform, Digitizers
-
Product
Handheld
-
Though lightweight and portable, a handheld digital oscilloscope can perform many of the complex analysis and signal irregularity identification techniques historically reserved for benchtop units. Manufacturers such as Fluke, Keysight, and Siglent now offer pioneering handheld units that improve efficiency by bringing lab scope capabilities to the field. Handheld oscilloscopes do vary in specification. If you need to find disturbances, choose a scope with fast sampling rates and a deep memory. A four-channel digital oscilloscope means multiple signals can be reviewed simultaneously.
-
Product
HandyScope HS5 + SureConnect: 200 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-220XMS-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 200 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
Mixed Signal Oscilloscope
Xprotolab Portable
-
Mixed Signal Oscilloscope: Simultaneous sampling of analog and digital signals.Advanced Trigger: Normal / Single / Auto, with rising or falling edge and adjustable trigger level.Meter Mode: Average, Peak to peak and Frequency readout.XY Mode (Plot Lissajous patterns or see the phase difference between two waveforms).Spectrum Analyzer with different windowing options and selectable vertical log.Horizontal and Vertical Cursors with automatic waveform measurements.Arbitrary Waveform Generator with Sweep on all parameters.Display options: Persistence, Different grid options, and more.Curve tracer function.
-
Product
SRJ (for IBP sensors)
-
The MEDTEQ SRJ is a test jig to measuring the step response of IBP sensors, which can assist in testing compliance with IEC 60601-2-34 frequency response. It is also suitable for manufacturers or test labs wanting to access the raw pressure waveforms via an oscilloscope.
-
Product
Oscilloscope 59 GHz, 4 Channels, 1mm inputs
UXR0594BP
-
The UXR0594BP is the 59 GHz, 4 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
Digital Storage Oscilloscope
2555
-
The 2550 Series digital storage oscilloscopes deliver performance and value in 2-channel and 4-channel configurations. With bandwidth from 70 MHz to 300 MHz and 2 GSa/s sample rates, these oscilloscopes offer 24 kpts/Ch waveform memory, 32 automatic measurements, and advanced triggering capabilities including math functions. Engineered to allow you to see more of your signal under test, the 2550 series’ widescreen 7” TFT display offers a significantly larger viewing area than typical economy oscilloscopes (5.7”).
-
Product
Oscilloscope 100 MHz, 2 Analog Channels
DSOX3012G
-
The DSOX3012G 100 MHz oscilloscope provides 2 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
USB Tester 2.0
TLS-0050
-
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
Product
Super Phosphor Oscilloscopes
SDS1000X-E Series
-
SIGLENT’s new SDS1000X-E Series Super Phosphor Oscilloscope is available in 100 and 200 MHz bandwidths and 2 or 4 analog channels. It has a maximum sample rate of 1 GSa/s and a standard record length of 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.The SDS1000X-E series employs a new generation of SPO (Super Phosphor Oscilloscope) technology that provides excellent signal fidelity and performance. The system noise is also lower than similar products in the industry. It comes with a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/ sec (sequence mode).
-
Product
Mixed Signal Oscilloscope: 33 GHz, 4 Analog Plus 16 Digital Channels
MSOV334A
-
33 GHz analog bandwidth4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
÷10, 500 MHz, 10 MΩ, Passive Probe
PP009-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
Talon 6 GHz RF/IF Sentinel Intelligent Signal Scanning Rackmount Recorder
Talon RTS 2620
-
- Search and capture system using Sentinel™ Intelligent Signal Scanner- Captures RF signals up to 6 GHz- Capture and scan bandwidths up to 40 MHz- 30 GHz/sec scan rate- Selectable threshold triggered or manual record modes- 16-bit A/D with 75 dB SNR & 87 dB SFDR- Built-in DDC with selectable decimation range from 2 to 65,536- Built-in DUC with selectable interpolation range from 2 to 65,536- 3U to 6U 19-inch rackmount server chassis with hot-swappable HDDs- Storage capabilities to 192 TB- RAID levels of 0, 5, and 6- Windows® workstation with Intel Core™ i7 processor- Optional RF upconversion- SystemFlow® GUI with virtual Oscilloscope, Spectrum Analyzer and Spectrogram displays
-
Product
Mixed Signal Oscilloscope: 100 MHz, 4 Analog Plus 8 Digital Channels
MSOX2014A
-
100 MHz4 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
Oscilloscope, 20 GHz, 160 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits
WaveMaster 8200HD
-
20 GHz, 12 bits, 160 GS/s, 200 Mpts/Ch High Definition Oscilloscope.
-
Product
NI-5191, 800 MHz, ±30 V, 10X Attenuation, Differential Active Oscilloscope Probe
781785-01
-
The NI-5191 is a differential, active voltage probe that offers 800 MHz of input bandwidth with a 10:1 attenuation ratio. You can use it with oscilloscopes that provide 50 Ω input impedance. You can power the probe using a Type-N barrel power connector from a USB port or using a 9 V alkaline battery.
-
Product
Logic Analyzer
LAP-321000U-A
-
Zeroplus Technology Corperation
Sample rate (Internal clock): 200MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Memory Depth (per channel): 1MbitsChannels: 32CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals. Glitch Capture Capability: 5ns. Bandwidth: 75MHz.
-
Product
Mixed Signal Oscilloscope - 500 MHz, 2 Analog Plus 16 Digital Channels
MSOX3052T
-
500 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
MOD MONITOR
TYPE HFX-1
-
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
Product
Pico Oscilloscope Range
-
High-end features such as serial decoding and mask limit testing are included as standard.
-
Product
WaveRunner Oscilloscope, 4 GHz Bandwidth, 4 Input Channels, 20 GS/s on 2 Ch Sample Rate
WaveRunner 9404
-
4 GHz, 20 GS/s, 4ch, 16 Mpts/Ch DSO with 15.4" Capacitive Display.
-
-
Product
Oscilloscope 70 GHz, 4 Channels, 1mm Inputs
UXR0704BP
-
The UXR0704BP is the 70 GHz, 4 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
Pulse Generator
PulseGen
-
Pulse Generator for use with an oscilloscope as a Time Domain Reflectometer (TDR).
-
Product
USB Hi-Res Digital Storage Oscilloscope, 1GS/s, 200MHz BW, 64M/channel
Acute TS2212H
-
*1. Up to 7x faster H/W initial time!*2. An additional reference clock input port to synchronize multiple-stacked DSOs!*3. TS2212H has twice the vertical resolution at 16-bits maximum!*PC-based (USB2.0 interface)*USB powered
-
Product
16 Channel, Single Slot, Bench Data Acquisition Unit with 6.5 Digit DMM
T3DAQ1-16
-
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes. Includes Spring Tip, tip protector, and standard accessories package.
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
Product
Digital Storage Oscilloscopes
-
Scientific Mes-Technik Private Ltd
Digital Storage Oscilloscopes
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
-
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Mixed Signal Oscilloscope: 70 MHz, 2 Analog Plus 8 Digital Channels
MSOX2002A
-
70 MHz2 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP022-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
