-
Product
VME Test Extender 6U/220mm 64X with P0
116EXT6122-0125R
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
VME sequencer
SIS3104
-
PCI Express and Ethernet to VME interfaceThe SIS3104 is the successor to the SIS3100 board.
-
Product
Special / Customer Spec. Crates
6U VME 3200
-
The VME 3200 crate series provides industry standard VME crates with redundant and hot-swappable front-side plugged in 500W cPCI power supplies in a compact and rugged design.
-
Product
Powered VXI Crates
-
VXI – (VME eXtension for Instrumentation): The demand for a compact, both flexible and fast industry-standard instrument-on-a-card architecture has driven the development of the VXI standard. The modular form factor, high bandwidth, and commercial success of the VMEbus made it particularly attractive as an instrumentation platform. The tremendous popularity of GPIB also made it attractive as a model for device communication and instrument control protocols.
-
Product
8-Channel VME Function Generator
V340
-
The V340 provides eight independent DDS-synthesized waveform outputs, each programmable for frequency and amplitude. Any output may be switched to a front-panel test connector, allowing in-crate calibration check without removing field cables.
-
Product
6U VME Single Board Computers
-
NAI's modular 6U VME single board computers can be configured with up to six NAI intelligent I/O and communication function modules. Choose from more than 40 intelligent I/O, communication, and Ethernet switch functions for the highest packaging density and greatest flexibility of any SBC board in the industry. NAI will integrate your choice of SBC and I/O functions to quickly meet your rugged system requirements. These SBCs are specifically designed for rugged defense, industrial, and commercial applications.
-
Product
8 Ch Dual Range Multievent Peak Sensing ADC
V1785
-
The VME interface is VME64 and VME64X standard compliant and features the A24/A32 and MultiCast addressing modes. The data readout occurs either in D32, BLT32, MBLT64 mode, or in daisy chain with 32/64 bit Chained Block Transfers. The module features a fully programmable RORA interrupter.The board is provided with the P1 and P2 VME connectors and fits into both V430 and standard 6U crates.
-
Product
Single Slot 6U, 32-bit Precision Timing Module
VME SyncClock32
-
The VME timing card is a standard board level product of Brandywine Communications. With a single slot 6U, 32 bit precision timing module, the VME card is compatible with VME computers. Precision synchronization to various inputs and convenient timing outputs to external equipment are standard on Brandywine’s VME card.
-
Product
16 Channel Dual Range Multievent QDC
V965
-
The Mod. V965 is a 1-unit wide VME 6U module housing 16 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance). For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section.
-
Product
16-Channel VME Analog/Thermocouple Input Module
V450
-
The V450 is a 16-channel 24-bit VME isolated analog-to-digital converter module which can acquire a wide range of DC voltages, including thermocouple readings with automatic cold junction compensation. Each channel is independently isolated with it's own A/D converter, signal conditioning, input protection circuits, and test relay.
-
Product
16/8 Channel 14 bit 500 MS/s Digitizer
V1730 / V1730S
-
The V1730S comes in a VME form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces.
-
Product
Special / Customer Spec. Crates
6U VME64x 6023 JLAB Crates
-
For the Thomas Jefferson National Accelerator Facility (JLAB) in Virginia (USA), a special version of the VME 6023 crate series with front to rear air-cooling was developed. “JLAB style” VME crates are available with standard VME/VME64 backplane and mechanics as well as with VME64x or VXS (see VXS section) backplane and IEEE 1101.10 compatible mechanics, (enhanced EMC and ESD shielding).
-
Product
VME Module
ICC-8-xxx
-
The ICC-8-xxx is the second generation of the ICC-8 board. Enhancements includes true RS-485 communications with jumper configurable I/O by the user. The ICC-8-xxx is a VME based, 8 channel intelligent and versatile solution to serial data communications designs.
-
Product
VME64x 2U/84HP 4 Slots
-
Hartmann Electronic’s 4 slot 19” rack mountable VME solution – The VME64x 2U system. This thin VME chassis comes with a 300W cPCI hot-swap power supply and horizontally oriented card slots. This platform conforms to VITA 1.1-1997 while providing a low profile, practical packaging solution for high-performance processors.
-
Product
64-Channel VME Analog Input Module
V230
-
The V230 provides high channel-count data acquisition for dense monitoring applications. The 64 channels are individually programmable for both input range and filtering. The three input ranges slightly exceed ±10 V, ±1 V, and ±100 mV, allowing confident measurements all the way to the end of common signaling ranges.
-
Product
PCI CONET Controller
A2818
-
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
-
Product
Dual Channel Digital Receiver
MS 1740
-
Dual Channel Digital Receiver is a complete high−frequency dual−channel A/D converter capable of sampling rates up to 210 MHz. It accepts two front panel analog inputs and delivers digital output samples over four FPDP (Front Panel Data Port) connectors utilizing FPDP standards. The Dual Channel Digital Receiver features two 12−bit Analog Devices AD9430 A/D Converters, and two user−configurable Xilinx® Virtex−IV Series FPGAs. It also features a VME A64/D64 slave interface for setting up operating modes and selectable A/D range, and optionally provides 32−bit access from the VMEbus to the FPGAs. It is an ideal system as a high−speed data acquisition front end for real time recording and digital signal processing systems.
-
Product
VME64X 7U 15 slot with P0
101V64XM15-0621R
-
7U VME64x Backplane 15-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
Product
16 Channel Input/Output Register
V977
-
The Mod. V977 is a 1-unit wide VME module that can work either as 16 channel general purpose I/O Register or as Multihit Pattern Unit; the operating mode is selected via VME and is signalled via front panel LEDs.
-
Product
VME J1 10 Slot with ADC Connectors
101VMEJ110-0590
-
VME J1 backplane 10 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
Quad 4 Fold AND/OR/MAJ, NIM-TTL TTL-NIM Translator
V976
-
The Mod. V976 is a 1-unit VME module housing four 4-input Coincidence Fan in/Fan out and NIM – TTL / TTL – NIM adapter sections. Each section features 4 inputs and 4 outputs on LEMO 00 connectors and can operate as a 4 channel level translator or as AND/OR gate.
-
Product
32 Channel Multievent Individual Gate QDC
V862
-
The Model V862 is a 1-unit wide VME 6U module housing 32 Charge-to-Digital Conversion channels with current integrating negative inputs. Each channel has an independent gate input (GATE i) logically ANDed with a COMMON GATE input; the input charge on the i-th channel is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section when both the GATE i and COMMON GATE signal are active.
-
Product
16-Channel VME AC Power Analysis Module
V180
-
The V180 is a single-width VME module that allows accurate and comprehensive measurement of AC power circuits. The V180 acquires powerline current and voltage inputs using approved current transformers and model C750 remote potential transducers.
-
Product
6-Channel VME Optical-to-Electrical Converter
V730
-
The V730 is a six-channel logic-level optical-to-electrical converter, packaged as a single-width, 6U VME module. When used with compatible Highland optical transmitter modules, the V730 provides fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
Product
VME64X 7U 6 slot with P0
101V64XM06-0621R
-
7U VME64x Backplane 6-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
Product
VME SBC
XVR19 6U
-
The XVR19 provides straightforward, cost-effective and low risk upgrades for users of previous XVR products, bringing enhanced processor performance, enhanced storage and improved protection against obsolescence. They will also be attractive for new programs looking to benefit from Abaco’s established and proven VME roadmaps.
-
Product
Backplanes
-
VECTOR Electronics and Technology, Inc.
Vector designs and manufactures standard and custom VME, VME64x, CompactPCI backplanes. Our backplanes meet and exceed industry standards and reliability and actively supply chassis and backplanes for numerous aerospace, missile and industrial programs.
-
Product
MIL-STD-1553 Four-Channel VME Board
BRD1553VME-4
-
The V-Orchestra™ is a four channel MIL-STD-1553B board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 64K word of internal RAM.
-
Product
Digital and Serial I/O
-
At Abaco, we're committed to the future of your VME systems, and we provide you with the flexibility and functional density you need.
-
Product
8 Channel NIM-ECL/ECL-NIM Translator
V538A
-
The Model V538 A is a 1-unit wide VME module housing 8 independent logic level translators. Each of the 8 channels accepts a NIM or ECL signal and provides two NIM and two ECL outputs (OUT 0÷7 A, B). The NIM and ECL inputs of each channel are ORed prior to fan-out.
