Filter Results By:
Products
Applications
Manufacturers
-
product
Millimeter Wave Converter
ZVA-Z Series
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
product
Waveguide Switches
Waveguide switches are electromagnetic switches with hollow circular or rectangular cross-sections and are used for routing RF energy in microwave communications, broadcasting, and in radar applications. Waveguide switches can be used to transfer both power and communication signals, and the bandwidth of a waveguide is in relation to its size, and thus always referred to by its size (e.g. WR112, WR90, WR75 etc.). Compared to coaxial switches, waveguides can route extremely high power signals over a narrow bandwidth at low to high frequencies, and now Lightweight Waveguide series is available.
-
product
Waveguide Bend
DWG8-WR-2C36.5-2561
Waveguide E-Plan Bend, Frequency 325~500GHz, VSWR 1.3:1, FUGP Flange
-
product
Millimeter Wave Converters
ZC-Series
*variable output power*wide dynamic range*wide frequency range*highly stable measurement*convenient handling
-
product
Waveguide Circulator/Isolator
RF Lambda’s waveguide circulators are typically used to prevent unwanted reflections. They offer low insertion loss and high isolation and are available in a variety of frequencies and power levels.
-
product
Waveguide Duplexer
Waveguide Duplexers supporting commercial communication to combine transmit and receive on to one antenna
-
product
Waveguide Bends
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
product
Millimeter Wave Spectrum Analyzer
Insight Product Co. offers the spectrum analyzer for frequency measurements of millimeter wave generators of continuous or pulsed signals. The spectrum analyzer can be ordered to cover a complete millimeter wave frequency band: 35-53 GHz; 53-78 GHz; 78-118 GHz; or 118-178 GHz and offer exceptional spectral resolution of 1-5 kHz.
-
product
Waveguide Power Sensor
E8486A
Keysight waveguide power sensors are fully compatible with Keysight EPM (E4418B/19B, N1913A/14A), EPM-P (E4416A/17A) and P-Series (N1911A/12A) power meters. The V8486A and W8486A are also compatible with the discontinued or obsolete power meters such as 435B, 436A, 437B, 438A, 70100A, E1416A, E4418A, and E4419A power meters.
-
product
Waveguide Power Sensor
V8486A
The V8486A waveguide power sensor measures average power over the frequency range 50 GHz to 75 GHz and power range -30 to +20 dBm.
-
product
Millimeter Wave Orthomode Transducers
We are developing a series of millimeter wave orthomode transducers. These orthomode transducers are fullband, compact components. They achieve astounding cross-polarization while maintaining Micro Harmonics’ impressively low insertion loss.
-
product
Waveguide To Coax Adaptors
The transitions from waveguide to coaxial line (SMA connector type) are offered up to 110 GHz.
-
product
Latching Waveguide Switches
Waveguide switches enable switching between two RF channels. The latching type is stable in both positions without holding current. Manual and automatic (electromagnetic) actuators are available.
-
product
Waveguide Cassette
Waveguide cassettes provide easy way for the network analyzer calibration and material properties as dielectric permittivity or (and) magnetic permeability measurements. By changing insertion sections, it is possible to calibrate "Short" and "Thru". Optional cassettes with quarter wave "short" inserters are available. Using this waveguide cassette, it is possible to do vector network analyzer calibration or additional scalar network analyzer calibration. Insertable sample holders supports two measurement methods: the rod in the centre of the waveguide and filled waveguide cross-section.
-
product
Millimeter Wave Amplifiers
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
product
Millimeter Wave Products
Reliable Millimeter-Wave High-Power Products for Airborne, Maritime and Ground Mobile Deployment
-
product
Double Ridged Waveguide Horn
DRH50
Frequency range: 4.5 GHz - 50 GHz VSWR (max): < 1.55:1Impedance: 50 O (Ohm)Connector: 2.40mm female Power (CW / Peak): 10 W / 20 W
-
product
Waveguides
A waveguide attenuator is an RF device specifically designed to reduce the power of a signal without affecting or reducing the waveform of the signal.
-
product
Waveguide To Coaxial Adapter
D25-BWC26NK-260
Waveguide To Coaxial Adapter, Frequency2.17~3.3GHz, Power 500W, WR340, Flange FDP26, N Type Female Connector
-
product
Double Ridged Waveguide Horn
DRH203
Frequency range: 200 MHz - 3 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 400 W / 750 W
-
product
Waveguide Probes
We are a leading Manufacturer & Exporter of Waveguide Probes such as Tunable Probe and Waveguide Matched from India.
-
product
Waveguide Power Detector
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
product
Waveguide Power Dividers
2-way power divider that operates from 220 to 330 GHz. The power divider offers a typical insertion loss of 2.3 dB and typical isolation of 20 dB. All ports are well-balanced and in-phase for power dividing or combining applications across the band. The power divider is configured as a right-angle package with WR-03 waveguides and UG-387/U-M anti-cocking flanges at all ports.
-
-
product
Waveguide Duplexer
RF Lambda’s waveguide duplexers are used to combine two frequencies onto a common waveguide. They offer high isolation and low insertion and come in a variety of frequencies. Hermetically sealed options are available upon request.
-
product
Double Ridged Waveguide Horn
DRH67
Frequency range: 6 GHz - 67 GHz VSWR (max): < 1.9:1Impedance: 50 O (Ohm)Connector: 1.85mm female Power (CW / Peak): 5W / 10 W
-
-
product
Double Ridged Waveguide Horn
DRH40
Frequency range: 4 GHz - 40 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 15W / 30 W
-
product
Waveguide Adapter
Waveguide adapters in a variety of waveguide standards / flange types and coaxial connectors
-
product
WR-8 Waveguide Straight
WAG-08-SXX
Precision mmw F-Band, WR-08, Straight waveguides are built with high precision and then gold plated for high corrosion resistance. They have very low loss and great VSWR. Manufactured to rigid specifications, these transmission line components provide minimum detrimental effects on the overall system VSWR.XX = length in inchesFeatures of WR-08, Waveguide Straights• 90 GHz to 140 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-8 Waveguide Straight
