RF Voltmeters
Measures RF voltages on tuned circuits.
-
Product
RF Loads
-
Bird manufactures a broad spectrum of devices from one watt to eighty kilowatts. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators and RF loads.
-
Product
RF Helmholtz Coil
-
The Beehive Electronics 135A RF Helmholtz coil generates a well-controlled, uniform magnetic field. It can be used to calibrate magnetic field probes, such as the Beehive 100 series, or for testing the susceptibility of other devices to magnetic fields. The Helmholtz coil comes supplied with a fixture that makes it easy to calibrate Beehive 100 series probes.
-
Product
Easy-to-assemble and Collapsible RF Test Enclosure With Fabric Shielding, ≥ 90 DB Isolation, 300 MHz - 18 GHz
dbTENT
-
The dbTENT is an easy-to-assemble, store and transport high-performance RF test enclosure. Whether you need to make measurements in the field or in the lab, the dbTENT provides superior 90 dB of isolation over a wide frequency range thanks to its patented double layer conductive fabric design. Featuring an interchangeable customisable I/O panel, the dbTENT meets all your needs for non-permanent isolated testing. With a setup time of only minutes, the dbTENT will get you ready for testing instantly in a wide variety of environments.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 3U VPX
Model 52791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x4- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Crimp Tool For MS-M Style RF Connector Pin
40-969-501-CT
-
This Crimp tool allows RF connections to be made to RG178 co-axial cable and the corresponding MS-M style housing 40-969-526-F.
-
Product
Solid State RF and Microwave Switches
-
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
Product
USB Programmable SPDT and SP4T Solid State RF and Microwave Switches
LSW Series
-
The Lab Brick LSW Series RF and Microwave Switch product family offers reliable, high isolation and low cost solid state switch products in both single pole double throw and single pole four throw configurations. These units require connection to a USB port for control and power. No additional DC supply voltage is required. Lab Brick RF and Microwave Switches are easily controlled and programmed directly from the included GUI and through the external control inputs. Lab Brick Switch API DLL and LabVIEW compatible drivers are also available for custom programming applications.
-
Product
HandyScope HS3: 100 MS/s 100MHz BW, 2 Channel, USB Digital Storage Oscilloscope, AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS3-100
-
The Handyscope HS3 is a powerful computer controlled measuring instrument that consists of four measuring instruments: a Voltmeter, Oscilloscope, Spectrum analyzer and Transient recorder. Also an AWG (Arbitrary Waveform Generator) is available. This new powerful and compact measuring instrument can solve almost every measurement problem.
-
Product
RF Chamber Fixtures
-
- 12” W x 12” D x 8” H internal dimensions- RF mechanical chamber can fit various wireless and Bluetooth products- test either commercial or consumer
-
Product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 75Ω, SMB
40-834A-002
Multiplexer Module
The 40-834A-002 (PXI) and 42-834A-002 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
High-Power Directional RF Wattmeters
81600-A Series
-
The 81600-A series of High-Power Directional RF Wattmeters are designed to measure RF power in 50-Ohm 6-1/8 inch coaxial transmission lines. The RF power is directly displayed on the 4-1/2 inch triple scale meter.
-
Product
PXI-2599, 26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
778572-99
Relay
26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2599 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2599 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
PXI-2556, 2.5 GHz, 75 Ω, Dual 4x1 PXI RF Multiplexer Switch Module
778572-56
Multiplexer Module
2.5 GHz, 75 Ω, Dual 4x1 PXI RF Multiplexer Switch Module—The PXI‑2556 is an RF signal multiplexer switch module. The multi-bank architecture of the NI PXI‑2556 makes it ideal for test systems that require parallel operations such as the stimulus/response testing of video RF devices such as tuners. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
PXI/PXIe RF Matrix, 16x8, 150 MHz, 50 Ω, SMB, With Y Loop-thru
42-724-011-L
Matrix Switch Module
The 40-724-011-L (PXI) and 42-724-011-L (PXIe) are 16x8 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
Generic RF ATE Test
-
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
-
Product
Digital and RF Testing
Amoeba® 5600
-
Built from the ground up based on AXIe and PXIe platforms, it offers the best of both worlds in terms of flexibility and power.
-
Product
PXI Single 8 to 1 RF MUX MCX 75 Ohm
40-834-101
RF Multiplexer
The 40-834-101 is a 75 Ohm 8 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-834 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
RF Training Kit And Lab Sheets
Y1800A
-
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
Product
26.5 GHz Or 54 GHz, Up To 4 GHz BW, RF PXI Vector Signal Transceiver
789600-08110
Vector Signal Transceiver
The PXIe-5842 is a vector signal transceiver (VST), which combines a vector signal generator and vector signal analyzer into a single four-slot PXI Express instrument. This VST provides the fast measurement speed and small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments. The PXIe-5842 benefits from PXI modularity and scalability, as up to four PXIe-5842 VSTs can fit into one 18-slot PXI Chassis. Additionally, the VST provides the error vector magnitude (EVM) performance required to test a variety of cellular and wireless standards such as Wi-Fi 7 and 5G NR. The PXIe-5842 supports frequency coverage and bandwidth availability for a wide range of semiconductor, aerospace, and defense applications.
-
Product
RF Rotary Joints
-
EVERAXIS is the market leader and supplier of choice for integrated waveguide assemblies, passive microwave components, RF Rotary Joints and rotating subsystems to the military and commercial radar and satcom markets. Working together with customers to create tailor-made solutions optimized to meet their needs has been the EVERAXIS business model for more than 70 years.
-
Product
PXI Dual 6 To 1 RF Multiplexer, 8GHz 50Ω SMA, Terminated
40-881A-002
Multiplexer Module
The 40-881A-002 is a dual 6 to 1 50Ω RF multiplexer with 8GHz bandwidth and automatic termination of unused signal channels. It is available as a single or dual MUX in one and two PXI slots respectively.
-
Product
PXI Single RF Attenuator 63dB in 1dB steps
41-180-021
Attenuator
The 41-180 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module
-
Product
PXI Dual 4 to 1 Terminated RF Multiplexer 3GHz 50 Ohm MCX
40-873-102
Multiplexer Module
The 40-873-102 is a 4 to 1 RF MUX with 2 banks in a single PXI slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
Electrostatic ESD Voltmeters & Monitors
-
Many applications require the measurement of a voltage or electrostatic charge on surfaces. Given the fact that the buildup of electrostatic charge during handling, manufacturing, assembly and other operations can impact production capacity and quality, ETS enables tests on stationary or moving surfaces.
-
Product
50 Ohm SMB to SMB Cable Assembly
40-977-511-0.5m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 8GHz, 50Ω, SMA
40-882B-001
Multiplexer Module
The 40-882B-001 (PXI) and 42-882B-001 (PXIe) are single 50Ω 4 to 1 RF multiplexers with 8GHz bandwidth. The 40/42-882B range has automatic termination of unused signals and is available as a single MUX in one slot, a dual MUX in two slots, or triple and quad MUXs in three slots.
-
Product
FieldFox C Handheld RF Analyzer, 4 GHz
N9913C
Microwave Analyzer
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
RF and Microwave USB Programmable Signal Generators
LSG Series
-
The Lab Brick LSG series of low cost USB-compatible RF and microwave signal generators covers frequencies from 20 MHz to 6 GHz with high output levels and excellent spectral purity. They require no additional DC supply voltage and offer several operating modes, including continuous-wave (CW) and swept-frequency. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 50Ω, MCX
42-877A-102
Matrix Switch Module
The 40-877A-102 (PXI) and 42-877A-102 (PXIe) are 50Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI 10 x 4 to 1 RF Multiplexer 1.8GHz 50 Ohm SMB Connectors
40-755-110
Multiplexer Module
The 40-755-110 is a 50 Ohm high-density RF multiplexer (4 to 1) array with 10 MUXs in a single PXI module. The 40-755 range is available with two connector options, an SMB connector that provides a frequency range of 1.8GHz and is available in single or dual PXI slots, or a multiway connector which limits the bandwidth to 1.3GHz but offers a high density solution occupying just one PXI slot. The RF switch design is identical in each case.
