Multifunction Meters
-
Product
Signal Level Meter
T1125
-
Hangzhou Softel Optic Co., Ltd.
The signal level meter, SE828C is able to measure EQ, C/N, V/A and trunk volt in the CATV analog system, the number keys is designed to direct input frequency so that work would be easier. It can measure 2 channels at the same time.
-
Product
Digital Meter
-
A meter that gives a separate reading, in the form of a decimal number, for each given input quantity.
-
Product
Dewpoint Meter
319
-
A hand-held dewpoint meter with both manual and automatic data logging in one gaugeIntegrated magnets allow the dew point gauge to be attached to the substrate during remote loggingStores 25,000 records in up to 999 batchesDustproof and waterproof gauge with fully sealed sensors (equivalent to IP66)Gauges can be recertified at Elcometer Authorised Service CentresRobust temperature sensorsEasy to use, intuitive menu structureMeasure and record climatic parameters:Relative humidityAir temperatureSurface temperatureDewpoint temperatureTΔ (the difference between surface temperature and dewpoint)Dry Bulb temperatureWet Bulb temperatureExternal temperature correction (K-type)Specific HumidityVisual and audible indication of user defined limits for any or all parametersUSB and Bluetooth® data output to ElcoMaster® software
-
Product
Multi-function Instrumentation
-
PXI Arbitrary Waveform and Programmable Function Generators as well as DC source cards and a precision standards module.
-
Product
Milli-OHM Meter
MR-30
-
*Double LCD Display*300,000 counts resolution*Measurement Range: 30mΩ~3MΩ*0.05% accuracy*20 Standard User setting memory sets*Sorting function and Relative percentage function*PASS/FAIL test result alarm*Computer Remote Manual and Auto Scan function*Manual and Auto Channel select*Sampling Rate: 30 sample/sec*High Resolution Temperature compensation and measurement*DUT Four-wire method*USB interface
-
-
Product
Phase Angle Meter
597C
-
Red Phase Instruments Australia Pty Ltd.
The Model 470A has similar software and performance as the Model 465C. It is packaged in a 19? style bench-top case with all connections on the front panel for use in meter test benches. It has inputs for comparison with another polyphase standard or 3 separate single phase standards for verifying calibration accuracy.
-
Product
Loop Meter
MZC-310S
-
The MZC-310S is a professional portable meter for testing electrical installations with over-current circuit breakers. The instrument measures short-circuit L-PE, L-N and L-L loop and prospective short-circuit loop current. A measurements can be done either with low testing current (up to 42A) with 2-pole method or high testing current (up to 280A) with 4-pole method that enables measurements with very high accuracy and resolution.
-
Product
12-24V Multi-functional Auto Tester With LCD Display
6511
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 12-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
Energy Meters
-
Energy meters play a crucial role in the control and management of energy, offering key information for improving energy efficiency. Energy meters enable the trading of electricity and billing processes for both end users and businesses. Through energy meters, monitoring and energy consumption optimization can be achieved.
-
Product
Handheld Dialysate Meter
Dialysate Meters™ Single & Dual Range
-
The choice of hemodialysis professionals for over 40 years, these compact instruments have been designed specifically to test dialysate solutions. By measuring electrical conductivity, they will quickly determine if dialysate concentrations are correct.
-
Product
Sound Meters
-
Sper Scientific sound meters include all the features and functions needed for basic noise level surveys or to meet the requirements for OSHA compliance, community noise ordinances or machine noise evaluation. These sound meters are used by: Industrial Hygienists, Sound Engineers, Construction Engineers, Municipal Code Enforcement officials, Industrial Quality Control, Environmental Scientists, and many more.
-
Product
Clamp-on Meter
SAC80
-
Analog AC clamp on meter. Color-coded scale plate. Fuse protected ohms circuit. Hold critical or hard-to-read measurements with point lock switch
-
Product
Covermeters & Half-Cell Meters
331
-
The Elcometer 331 is an all in one gauge that combines the rebar locator, concrete covermeter and half-cell measurement, making site visits quicker and more convenient.
-
Product
Benchtop Meter
pH 700
-
Economical, user-friendly and accurate, the Eutech pH 700 is your ideal choice for routine applications in laboratories, productions plants and schools.
-
Product
LCR Meters
-
PeakTech Prüf- und Messtechnik GmbH
A type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component.[1] In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value. Readings should be reasonably accurate if the capacitor or inductor device under test does not have a significant resistive component of impedance. More advanced designs measure true inductance or capacitance, as well as the equivalent series resistance of capacitors and the Q factor of inductive components.
-
Product
Leakage Clamp Meters
3920 CL
-
Standard Electric Works Co., Ltd
● Designed for testing AC current and AC voltage. ● 5 ranges for AC current testing.● The best resolution of leakage current measurement is 0.1mA.● Frequency selection : 50/60 Hz and Wide.● Data hold function.● Low battery indication.
-
Product
Light Meter
PLMT56
-
Light Meter Measures In LuxOver-Range IndicatorLong-Life Silicon Photo Diode InsideMeasurement Rate: 1.5 Times per SecondMax Range: 50,000 LuxAccuracy: +/- 5% Under 10000 Lux, +/- 10% Over 10000 LuxMax Resolution: 0.1 LuxDimensions: 7.40' H x 2.52' W x 0.96' DAccessories Included: 12V A23 Battery, Photo DetectorSold as : Unit
-
Product
Switchboard Meters
-
Hoyt Electrical Instrument Works Inc.
Glass window, ABS Resin frame and case, PC glass fiber base Mounting fittings included. Black base and frame, white scale plate and meter body.
-
Product
Multifunction Testers
1663
-
The 1663 installation tester delivers the full-featured functionality and advanced measurement capabilities that professional installers need. It is compact and lightweight (less than 1.3 kg) and comes with a padded carrying and waist strap for convenient handling.
-
Product
Portable pH Meter
Starter 300
-
This portable meter offers convenience, reliability and durability in one compact design.
-
Product
50Hz-100kHz LCR Meter
11022/11025
-
Chroma Systems Solutions, Inc.
0.1% basic accuracyTransformer test parameters (11025), Turns Ratio, DCR, Mutual Inductance0Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, 100kHz test frequencies21ms measurement time (≥100Hz)Agilent 4263B LCR Meter commands compatible4 different output resistance modes selectable for non-linear inductor and capacitor measuringHigh resolution in low impedance(0.01mΩ) and high accuracy 0.3% till 100mΩ rangeAdjustable DC bias current up to 200mA (constant 25Ω) (11025)1320 Bias Current Source directly control capability0.01mΩ ~ 99.99MΩ wide measurement range (4 1/2 digits)Dual frequency function (11022 option) for automatic productionBIAS comparator functionComparator function and 8/99 bin-sorting functionPass/fail judge result for automatic productionHandler interface trigger edge (rising/falling) programmableTest signal level monitor functionStandard RS-232, GPIB, and Handler I/FOpen/short zeroing, load correctionLabView® Driver
-
Product
Magnetic Field Meter
-
Measurement for the magnetic field generated from Direct Current (DC, with display by N/S Magnetic polarity) or Alternating Current (AC in 40-500Hz).
-
Product
TPS-Effusivity Meter
-
Thermal Effusivity (W√s/m2K) is described as a materials ability to exchange heat with its surroundings. Surface haptics is a branch of psychology, describing the sense of touch, localized to the skin surface. The feeling of warmth and coolness (thermal effusivity) makes up the feeling of comfort, or the desired effect, which goes into the touched material surface. This is an important field of measurement for textiles, fabrics and solids.
-
Product
Tubidity Meters
-
an instrument that measures the cloudiness or haziness (turbidity) of a fluid, caused by suspended particles like silt or microorganisms, by shining a light through the sample and detecting how much light is scattered or blocked, quantifying water clarity for health, environmental, and industrial purposes
-
Product
Multifunction Engine Gauge
1U378-series
-
This 3” instrument combines the three essential engine parameters in a compact package. Rugged D’Arsonval meter movements with two jewels are used to indicate cylinder head and oil temperatures. A brass bourdon tube mechanism precisely indicates oil pressure. A selection of fittings is available to simplify installation.
-
Product
Light Meters
-
Using a light meter you can track light levels anywhere and with a fast, stable and accurate sampling result.The result can be seen in a large digital LCD display.
-
Product
Field Meter
EAP 301 HD
-
The AP301 HD is a field meter with total coverage of the terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
Product
Voltage Meter
MN6I
-
The mezzanine is designed to measure instantaneous voltage values through six isolated channels with differential inputs.
-
Product
Optical Power Meter
PM203
-
The PM203 optical power meter can be used to measure the radiometric power in a beam of monochromatic or narrow band light. Using the internal calibration table the micro-processor controlled PM203 displays directly the optical power in Watts or dBm or the calibration wavelength.
