Voltage Indicators
1) Digital Voltage Indicator. 2) Digital Visual Interface, is a standard for a uniform connector that can handle both digital and video signals.
See Also: Indicators, Angle Position Indicators, Fault Indicators, Loop Indicators
-
-
product
Cross Voltage Testers
designed to perform the 60 Hz power line cross test/AC power fault tests required in GR 1089 issue 6 table 4.5 surge test 3,4, 4.3,and 6, and for UL 1950 section 6.4 paragraph 3 and 4.. Preset and Adjustable Time Settings Measuring Terminals including Voltage Sense and Current Shunt portals provide a safe location for users to accurately measure test voltages and output current while setting up tests. Calibration of the Mini_PT-600 is designed to be performed with a simple handheld multi-meter and the removable Currents Shunts can be easily sent to a calibration laboratory if required.
-
product
Medium Voltage Iron Core Oil-Immersed Shunt Reactor
Iron core Oil-immersed Shunt Reactors act as an absorber of reactive power to increase energy efficiency of the power system.
-
product
Acute High Voltage Differential Probe, 20x/200x, 25MHz, 1400V
ADP2025
*USB Powered (or Power Bank)*Bandwidth up to 25 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
product
PXI 12xSPST High Voltage Power Relay Module
40-330-003
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
product
PoE Voltage Monitor Detect & Verify
PE-400
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
product
Low Noise High Precision High Voltage Amplifier
WMA-280
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
product
Dualite High and Low Voltage Tester
22400
Two circuit testers in one - troubleshoot both primary and secondary circuits. Use as a primary circuit tester on 6 and 12 volt circuits or on secondary or high voltage circuits to check out spark plugs. 48" lead wire.
-
product
PXI/PXIe High Voltage Multiplexer, Single 9-Channel, 1-Pole
42-321-104-HI
The 40-321-104-HI (PXI) and 42-321-104-HI (PXIe) are single 9-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
High Voltage Reed Relays from Pickering Electronics
Pickering Electronics' High Voltage Reed Relays are well suited for Instrumentation, Industrial Process Controls and General Purpose requirements. *Ideal for high-power applications*Plastic package with internal mu-metal magnetic screen*3V, 5V, 12V or 24V coils, diodes are optional*Dry instrument grade switches*Pickering's SoftCenter technology
-
product
OEM Voltage Input0 to 2.5/10/25V
TGPR-0700
A voltage input data logger that is supplied uncased so that it can be built into custom applications.The TGPR-0700 can be used to record the output from a number of industry standard sensors. Common applications include pressure and windspeed monitoring.
-
product
High Voltage Dry Reed Relays For up to 15 kV
SERIES 62 & 63
ungsten switches with power rating of 50 Watts maximum? Three switch types:5kV stand-off, 3.5kV switching10kV stand-off, 7.5kV switching15kV stand-off, 12.5kV switching? Series 62 has push-on connectors on top face for EHT and solder pins and nylon studs on the underside for PCB mounting
-
product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-908-HI
The 65-231-908-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
High Power & Voltage Pack Testing System
FTF
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery Packs
-
product
Dual Channel High Voltage Linear Amplifier
F1020
This unit contains two independent amplifiers that share common ground reference and power supply. Left channel correspond to the F10A model and right channle corresponds to the F20A model.
-
product
PXI/PXIe High Voltage Multiplexer, Dual 4-Channel, 1-Pole
42-321-100-HI
The 40-321-100-HI (PXI) and 42-321-100-HI (PXIe) are dual 4-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
High Voltage Differential Probe
ADF25A
Permits conventional grounded oscilloscopes to be used for the display and measurement of multiple floating signals with high common mode voltages
-
product
51-Pin REDEL High Voltage Cable Assembly, Male To Unterminated, Ferrules, 0.25A, 1m, 29 Wires
A051KMR-F-HA100-29
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with ferrules constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips areprovided to secure the connector to associated product.
-
product
Standard Voltage 50 Pin D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
4 (High Voltage) D/A Outputs (+20 VDC to +80 VDC)
DA4
The DA4 module features 4 high-voltage D/A output channels with a maximum full-scale range of ±80 VDC at ±10 mA (max).
-
product
70-440V AC Non-Contact Voltage Detector With Buzzer
1966A
Peaceful Thriving Enterprise Co Ltd
*Check voltage on 70-440V AC.*With CE, cUL and RoHS Approval.*Operates by two LR44 1.5V batteries.*LED will glow if AC voltage is present.*Check for proper ground connection of electrical appliance.*Test electrical lines, cables, sockets, fuses, switches and etc.
-
product
Dual Channel High Voltage Linear Amplifier
A400D
This unit contains two independent A400 amplifiers that share common ground reference and power supply.
-
product
Process / Voltage / Current
Calibrator high precision process signals able to measure and generate current and voltage.
-
product
High Voltage Transformer
RR manufactures HIGH VOLTAGE TRANSFORMERS for various Industrial Applications.
-
product
Voltage Variable Attenuators
Voltage variable attenuators (VVAs) that offer up to 60 dB of attenuation across a broad range of frequencies from 400 MHz to 18 GHz. These voltage variable attenuators are frequently used in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.
-
product
51-Pin REDEL High Voltage Cable Assembly, Male to Unterminated, Cut Ends, 0.25A, 1m
A051KMR-C-HA100
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with cut ends constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips are provided to secure the connector to associated product.
-
product
Voltage Variable Attenuators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
product
T3 Low & High Voltage Differential Probes
T3 Series
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
product
Optical Voltage Probe
400-02
Srico’s optical voltage probe uses advanced, proprietary optical chip technology to achieve precise, interference-free measurement. Our sensor and optical fibers are made of dielectric materials. This facilitates a high degree of isolation between the voltage test point and the instrumentation system ⎯ at a safe distance of 100 meters and more. This system senses, measures, and transmits electrical data very accurately.
-
product
High Voltage 50-Pin D-Type Connector & Cable Accessories
The High Voltage 50-Pin D-Type connector is used on high voltage PXI and LXI switching products to provide a high voltage connector solution. Connection solutions for modules with Standard Voltage Rating D-Type connectors are also available.
