Isolation Amplifiers
-
Product
2-Port Isolated RS-232, M.2 B Key(2242, USB), DB9
PCM-34D2R2
-
Meets Advantech iDoor Technology StandardM.2 2242 B Key compliant (USB 2.0)Speeds up to 921.6 kbps for extremely fast data transmissionSupports any baud rate setting (200 bps ~ 921.6 kbps)The PCM-34D2Rx (2-ports) supports Isolated ProtectionCompatible with embedded automation PC UNO-1/2/3/4 seriesCompliant with FCC/CE Class A CertificationOperation temperature 0~60 degree support
-
Product
High Speed Amplifier
-
TI offers the industry's most comprehensive high speed amplifier portfolio with the widest bandwidth and best in class distortion, precision and power consumption across a broad range of supply voltages. Our industry leading FDA's, DVGA's, TIA's and General purpose amplifiers coupled with the reliability and longevity of our parts makes TI the ideal supplier of high speed amplifiers.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
RF Amplifier Modules
-
a compact, self-contained electronic assembly that boosts low-power radio frequency signals to higher power levels.
-
Product
HF Amplifier
Prometheus
-
The design of the Prometheus is the result of over 10,000 hours of research and development, encompassing hundreds of hours of mathematical analysis, computer simulation and modeling, and numerous prototypes and experiments spanning over a five year period. The result is a rugged, commercial quality amplifier designed to run cool under 1500W continuous SSB, CW or RTTY, with special ferrite transformers and combiners designed for full power operation even on 160 meters. Although our custom transformers are more expensive and difficult to manufacture than competing designs, they do not saturate or heat up beyond the Curie point, thereby becoming irreversibly damaged and destroying the RF transistors in the process.
-
Product
Standard Pulsed Amplifiers
-
An electronic device designed to strengthen short, sharp bursts of electrical or radio-frequency (RF) signals without changing their original wave shape.
-
Product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
-
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
Product
Femtosecond Multipass Ti:sapphire Amplifier
MPA 50
-
MPA 50 is a multipass Ti: sapphire amplifier based on a two-mirror confocal design and containing a pulse stretcher, a pulse compressor, a pulse picker, synchronization electronics, and the Faraday isolator.
-
Product
PXI 8/16-Channel Isolated D/A Converter
M9185A
Digital / Analog Converter
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
Product
RF Medium / High Power Amplifier
-
Corech Microwave’s RF medium/high Power Amplifier(PA) frequency ranges from 0.1 to 52 GHz, up to 100W high power output (CW or Pulse). Narrow-band & wide-band ready modules are available SMA, 2.92mm, 2.4mm, WR28, WR24 and PIN connector options are available.
-
Product
16-Ch Isolated Digital I/O Module With LED
ADAM-5055S
Digital I/O Module
I/O Type: 8 DO & 8 DIOptical Isolation: 2500 VdcPower Consumption: 0.68 W (Typical)16-channel
-
Product
32-CH Isolated DIO Card
LPCIe-7230
Analog Input Module
ADLINK LPCIe-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCIe-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCIe-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCIe-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
Product
Electric Transducer Driver Amplifier
7620
-
The Krohn-Hite Model 7620 is a 17/34 watt, wideband power amplifier that offers extended output power and voltage capabilities. Performance features not available in other power amplifiers, the 7620 provides a differential output and is able to deliver 17/34 watts of continuous power (68 watts at dc) and 141V/282V rms (400V/800Vp-p). It can also provide plus and minus dc voltages simultaneously.
-
Product
Amplifiers
-
Teledyne Lincoln Microwave design and manufacture RF amplifiers utilising the latest semiconductor technology. Our portfolio includes low noise amplifiers (LNA’s), power amplifiers and pre-amplifiers. These can incorporate linearization, filtering, phase and amplitude control functionality.
-
Product
RS422 Mode SI-module With Optical Isolation
MX422-G
-
RS422 mode SI-module with optical isolation
-
Product
32-Ch Isolated Digital Input And 16-Ch PhotoMOS Relay USB 3.0 I/O Module
USB-5855
-
USB 3.0 SuperSpeedDaisy chainable by built in USB hub32-ch digital input and 16-ch PhotoMOS Relay output (Form A) isolationWide input voltage range (10 ~ 30 VDC)1500 VDC optical isolation for relay outputsQuick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
High Voltage Optically Isolated Probe, 700 MHz Bandwidth. Includes soft-carrying case.
DL07-ISO
-
The DL-ISO enables highest confidence in GaN and SiC device characterization with highest accuracy, best signal fidelity, and comprehensive connectivity.
-
Product
PCI-8433, 4-Port, PCI, Isolated, RS485/RS422 Serial Interface Device
779146-01
Serial Interface
The PCI‑8433/4 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Amplifier Modules Band Specific
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Low-Noise Parametric Amplifiers
-
Insight Product Company offers Low-Noise Parametric Amplfiers based on Monolithic Integrated Circuits (MIC) in the frequency range of 30 to 100 GHz.
-
Product
Bi-Directional Amplifiers
-
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
Product
Amplifiers
-
Alnair Laboratories Corporation
A specially designed Erbium-doped fiber amplifier which offers a superior optical amplication performance with a very high gain factor and a minimal added noise. A near quantum limited noise figure of typically 3.8dB, and a small-signal optical gain of over 50dB is achievable with input signal as low as -50 dBm reflecting the impact of the specialty fiber and composite amplifier design, making it an indispensable amplifier for weak optical signals.
-
Product
16 Relay Output Board, 8 Isolated Digital Input Channels, 24V
APCI-2200-16-8
-
16 electromechanical relays with change-over contacts ? Max. switching voltage for the relays: 60 V/DC, 48 V/AC ? Max. switching current: 1 A ? Short response time ? Option: 8 input channels for AC voltage, optically isolated, input voltage range: 12 - 24 V DC ? Watchdog: software-programmable release, stop and time selection.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800A (1RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800A (1RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Automotive Audio Power Amplifiers
-
ST is the recognized leader in automotive power amplifiers. Our car audio amplifiers provide the traditional clean and powerful sound that users have come to expect, as well as all the protection and safety features needed to make our devices robust in an automotive environment.
-
-
Product
Defect Isolation
-
*Traverse through the physical design to trace nets and vias down to the defect location*Utilizes industry standard LEF/DEF design files, scan-based test information, tester fail logs and diagnostic reports to determine and isolate the physical defect location*Enables the user to leverage their diagnostic experience to determine the root cause of the defect*Interactive layout viewer displays scan chains, mapped mismatches of scan cells, layers, nets and subnets with search capabilities(component, net, cell)*Physical XY coordinates are always displayed for components and nets to guide the user through the design to quickly identify suspect sites for FA using techniques like Emission, OBIRCH, LIVA, TIVA, or FIB
-
Product
20dB In-Line Amplifier
HSA-20
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*Excellent Zinc die-casting chassis, with good shielding feature. *All ports can be passed by DC. *Output ports are F-British system, impedance 75Ω.* Perfect technique of superficial treatment guarantees frequency respondence.
-
Product
12-bit, 100KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3001-4
-
4 single-ended or 2 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
8-Ch, 16-Bit Isolated Analog Input EtherCAT Remote I/O Module
AMAX-4817
-
Suitable for EtherCAT networks8-ch, 16-bit analog input channels with 2,500 VDC isolation±275 V high common-mode voltage rangeQuick removable European type connectorSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo rotating switches for up to 256 slave IDs
