High-Pass Filters
Refine signal, allowing the transmission of signal above a specific corner frequency, while strongly attenuating the frequencies below.
-
product
dv/dt Filters
dV/dT Output Filter Modules effectively protect motors against these high voltage spikes due to the use of motor cables between IGBT based motor drives and motors.
-
product
Third Harmonic Filter
HBF-T
Lifasa - International Capacitors, SA
HBF-T filters are designed to block the 3rd harmonic, reducing the neutral currents in three-phase installations where there are installed harmonic generating loads connected between phase and neutral. It is basically passive filters based on a parallel combination of inductance and capacitor.
-
product
RF Filters
Smiths Interconnect is committed to providing technically advanced, high quality “state-of-the-art” RF Filters, Multiplexers, Switched Filter Banks, and Integrated assemblies, from 100 KHz to 65 GHz. All products are subject to the same rigorous design, manufacturing, and inspection criteria. Regardless of the application, our internal process and procedures help ensure that all products are fully compliant to all specifications. Our R & D activities are constantly evaluating new materials, plating techniques, and manufacturing processes to offer the highest performing components available today.
-
product
Anechoic Chamber Filters
RF leakage through Ethernet and USB cables can destroy even the best RF enclosures and chambers. The need for filtering in the ever congested RF environment requires special filters that can pass USB 2.0 and 10/100/1000 Mbps Ethernet signals and filter out unwanted higher frequencies such as cellular and WiFi. The Adaura Technologies USB/Gigabit Filters provide one GigE and one USB 2.0 pass-through connections while filtering out other RF up to 8GHz. It has a small form factor to allow easy installation. It is a most cost effective solution for a clean chamber set up. In a typical chamber, WiFi signals are reduced to <-100dBm with this filter installed.
-
product
Band Pass Filters
VDI offers up-converter modules for communication applications. The double sideband nature of the up-converter modules makes filtering necessary. VDI has designed filters to filter one sideband and preserve signal modulation. These filters offer low passband insertion loss and high out-of-band rejection. Custom filters may be available upon request. NRE (non-recurring engineering) fee may be required.
-
product
Narrow Band Filters (Single Octave)
POWER-POLE® Series
The POWER-POLE® Series of tunable filters provides improved RF performance with increased power handling capability and the lowest insertion loss for a given bandwidth. The product line includes several standard designs in various frequencies to support almost any application. Approximate performance is summarized in the POWER-POLE Series Selection Guide.
-
product
Narrow Band Filters (Single Octave)
NANO-POLE® Series
The NANO-POLE® is designed for optimal size, DC consumption, RF power handling, insertion loss, signal purity and linearity. The NANO-POLE® provides a minimum center frequency step size of 10 MHz typically but can be modified based upon request. The NANO-POLE® requires a +3.0 V supply that typically draws 5 mA when not hopping. The supply voltage should be adequately filtered as noise present on this pin will influence the RF signal purity. The NANO-POLE® uses SPI control interface.
-
product
Fabry-Perot Based Scanning Filter
This new type Fabry-Perot Based Scanning Filter (FPSF) is based on Optoplex proprietary fiber optical Fabry-Perot Etalon technology. It offers F-P based scanning filter with central wavelength at 1060nm, 1310nm, 1550nm or other customized wavelength. It can be tuned manually or automatically by scanning over a wide spectral range from 10nm to 100nm with bandwidth from 0.05nm to 1.0nm. FPSF features less than 3dB insertion loss and as high as 1kHz scanning frequency. Its unique high reliability and low insertion loss design presents the most cost-effective solution for OEM application from telecommunication to fiber sensing interrogation.
-
product
Fiber Bragg Grating And Optical Filters
Exail is committed to develop and manufacture optical components with excellent performances to support the most diverse industrial applications such as Telecom, sensing, defense, space, fiber laser and harsh environment.
-
product
Filtering Network TAPs
Filtering network TAPs allow you to filter out the packets and traffic that is not needed by the tool to perform its function. Filtering ensures that monitoring ports do not become oversubscribed with unneeded data. Filtering TAPs are purpose-built hardware devices that let you see every bit, byte and packet.®
-
product
Tunable Optical Filters
DiCon's MEMS tunable optical filter offers many advantages over a traditional tunable optical filter; increased accuracy & resolution, a faster tuning speed, as well as a durability that will last for over a billion tuning cycles, all in a compact package. Options are available for either 100 GHz or 50 GHz channel spacing as well as operation in either the O-band, C-band or L-band wavelength ranges.
-
product
Capacitor for AC Filtering
PECA5
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
product
Automated Filter Tester
8127
The Automated Filter Tester 8127 is designed to comply with commercial respirator standards around the globe and has a proven track record of durability, reliability, and minimal maintenance, meeting the demanding requirements of manufacturing and quality control environments. Whether you are looking for a stand-alone tester to check a few filters per day or need to integrate your tester in an automated, high volume production line, CERTITEST AFT’s are up to the challenge
-
product
Optical Filter Sets
Our filter sets support a great range of fluorophores for microscopes and imaging systems. Patented design techniques drive some of the most spectrally sophisticated optical filters on the market. High transmission, steep edges, precise spectral edge placement, and optimized blocking combine for more reliable measurements. A wide selection of individual bandpass filters and dichroic beam-splitters support unique applications, and world-class manufacturing and cutting-edge metrology ensure consistent performance that always meets specifications.
-
product
Co-Siting Filters and Combiners
*Multiplexers, Duplexers, Diplexers and Antenna Sharing Combiners*Enables multiple base stations to share a single antenna*Many of the units offer both High and Low band support*Ideal solutions for either ground based and tower based antenna sharing*Compact lightweight rugged construction
-
product
RF Filters
Raymond RF offers a complete line of RF filters ranging from 0.4A to 600A in both stand-alone and cabinet-mounted configurations for our QuietBoxes and Anechoic Chambers. Both styles of filters can be supplied with NPT pipe nipples and flange nuts for mounting directly on a QuietBox or Anechoic Chamber. Alternately, both styles of filters can be remotely mounted with shielded conduit running between the clean end of the filter and the QuietBox or Anechoic Chamber.
-
product
Automatic Batteries with Filters with Thyristors
BATLVFS800
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations.
-
product
DC Filters
This DC filter provides substantial noise reduction on DC power lines of up to 50V 9A. Filter provides noise suppression in both directions protecting your DC lines from noise generating by a particular piece of equipment or protecting your sensitive equipment from noise coming from DC power supply or other loads. DC filter provides noise suppression for both power lines – positive and negative, plus common-mode noise vs. ground. Filter uses plug-in terminal block for connections and mounting flanges for easy installation. Its rugged construction makes it easy to fit in many industrial tools.
-
product
Individual Optical Filters
Our comprehensive line of Semrock optical filters helps your design attain the best signal-to-noise ratios. Steep spectral edges maximize useable bandwidth, and high transmission or reflection captures the brightest images with best-in-class Flatness. Deep and extended blocking are optimized for your application, minimizing background and crosstalk while reducing cost. Select from the extensive catalog or go with a custom filter to your exact specifications, and remain confident of uncompromising quality, reliability, and reproducible results.
-
product
Switch Filter Banks
PMI designs, manufactures, and produces high quality state-of-art-art switch filter banks that feature 2 to 32 multichannel configurations, frequency coverage up to 26 GHz, low profile packaging, connector options, and high channel to channel isolation. Select from standard designs or custom Switch Filter Banks can be designed to meet your most demanding electrical, mechanical, and environmental specifications.
-
product
R.F. Coupler and high Pass Filter
7415-3
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
product
Capacitor for AC Filtering
PECA4 (900V)
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines
-
product
Low-PIM, Low-Power Filter Solutions for Monitoring Broadband Emissions
Bandpass/Bandstop, Notch, and HighpassCompact Design for Rack Mounting of Several BandsSuitable for Monitoring Emissions from Semiconductors,TX/RX Chipsets, SAW/BAW Filters, Cell Phones,Printers, PDA’s, etc.
-
product
2 to 8 Channel Anti-Alias Low-Pass Filter Card
AAF-1
The AAF-1 is a multi-channel anti-alias low-pass filter board designed for front-end signal conditioning in PC-based or stand-alone 12-bit A/D conversion systems.
-
product
Noise Suppression Products / EMI Suppression Filters / TVS Diodes (ESD Protection Devices)
Murata noise suppression products include compact EMI suppression filters that efficiently eliminate noise, L Cancel Transformers (LCTs) that greatly suppress noise in high-frequency bands by reducing the ESL generated inside capacitors and in boards, and TVS Diodes that guard semiconductor devices against electrostatic discharge from external sources. Murata supplies products that support a variety of approaches to suppressing noise.
-
product
Lowpass Filters
Frequency range of this lowpass filter is DC to 100 MHz and the passband is 100 MHz. PE8719 lowpass filter is one of over 40,000 RF, microwave and millimeter wave components supplied by Pasternack. Our 5 section low pass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
-
product
LV Iron Core Harmonic Filters
Nonlinear loads such as power electronics based equipment and electric furnaces are sources of harmonic currents leading to harmonic distortion, which is one of the most important parameters for defining the power quality. Most of the commercial loads such as personal computers, photocopy machines, power supplies, and compact fluorescent lamps; and industrial loads such as AC and DC motor drives inject harmonic currents into the network that they are connected to.
-
product
Automatic Batteries with Filters with Thyristors
BATLVFS1200
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations
-
product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model T360M
Teledyne Advanced Pollution Instrumentation
The Model T360M CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 1.28 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range, making this instrument an ideal choice for CO2 reporting requirements associated with dilution CEMS.
-
product
Light Measurement Optical Filters
International Light Technologies
Optical filters are often used to attenuate certain wavelengths of light and produce an overall desired detector response.
