-
product
Banking, ID & Transport
ST’s secure microcontrollers are designed for a wide range of applications including SDA & DDA banking, identification, transport and Pay TV solutions. From traditional smart cards to innovative wearables and biometric solutions, ST offers a complete portfolio of contact, dual-interface and contactless secure microcontrollers.
-
product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
product
Automatic Voltage Regulating Relay
NMC introduces low cost microcontroller based basic automatic voltage regulating relay, type : h-101.
-
product
Smartcard Interfaces
ST offers complete analog interfaces for asynchronous 1.8 V, 3 V and 5 V smartcards. They can be placed between the card and the microcontroller with only a few external components to perform all supply protection and control functions. Main targeted applications are smartcard readers for set-top boxes, IC card readers for banking, identification and pay TV.
-
product
LilyPad Light Sensor
The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Each sensor outputs voltage between 0V and 3.3V depending on the level of ambient light shining on it. As more light is applied on the sensor, more current will flow from the board through the signal tab to the microcontroller you connect the sensor to. If the sensor receives no light, no current will flow through it. In a typical indoor lighting situation, the sensor will output around 1 to 2V. Adding this board into your next e-textile or wearable project will really open up the possibilities by being able to incorporate light level sensing capabilities.
-
product
Pro Micro
5V/16MHz
Here at SparkFun, we refuse to leave 'good enough' alone. That's why we're adding to our line-up of Arduino-compatible microcontrollers once more! The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will pl...show more -
product
Renesas Synergy™ Platform
with the first fully qualified embedded microcontroller software and hardware platform. We help you reach more people, sooner.
-
product
Sunshine Duration Sensor
SD4
Four identical omni-directional sensors under a hemispherical shading canopy. Embedded microcontroller executes a sophisticated contrast-evaluation algorithm to accurately discriminate direct sunshine from diffuse sunlight.
-
product
Profiling and Coverage Analyzer Tool
Analyzer
One of the most effective debugging techniques in embedded development and testing is tracing. Tracing means recording microcontroller activity, such as Program or Data flow.
-
product
Universal Plug-in Module With I/O And CAN FD Interface
PCAN MicroMod FD
The PCAN-MicroMod FD is a small breadboard with CAN and CAN FD connection on the one hand and various physical inputs and outputs on the other. Both sides are logically linked using the NXP LPC54618 microcontroller. Electronics developers can use the PCAN-MicroMod FD to easily integrate I/O functionality with a CAN connection into their project.
-
product
68HC11D Simulator
SIM11D
Simulate your M68HC11 microcontroller designs on your personal computer. Helps find hidden errors easily and efficiently.
-
product
Sound Impact Sensor
29132
The Sound Impact Sensor detects sound from up to 3 meters away. This human input device lends noise-activation possibilities to your microcontroller projects.
-
product
Programmable Sensor Module With CAN Connection
PCAN GPS
The PCAN-GPS is a freely programmable sensor module for position and attitude determination. It has a satellite receiver, a magnetic field sensor, an accelerometer and a gyroscope. The recorded data can be transmitted on a CAN bus and logged on the internal memory card. The data is processed by a microcontroller from the NXP LPC4000 series.
-
product
Triple-Axis Accelerometer (+-2g/4g/8g/16g) w/ I2C/SPI
ADXL345
Filling out our accelerometer offerings, we now have the really lovely digital ADXL345 from Analog Devices, a triple-axis accelerometer with digital I2C and SPI interface breakout. We added an on-board 3.3V regulator and logic-level shifting circuitry, making it a perfect choice for interfacing with any 3V or 5V microcontroller such as the Arduino.
-
product
CM2302 Digital Temperature & Humidity Sensor
28059
Do you need convenient environmental input for your microcontroller projects? The CM02302 supplies both temperature and relative humidity data when queried. This sensor is factory pre-calibrated, so you won’t need to calibrate it before using it in your project.
-
product
BME680 Environmental Sensor
28061
Raise your project’s environmental awareness with the BME680. The Bosch Sensortec BME680 Integrated Environmental Unit combines a gas sensor with air pressure, humidity, and ambient air temperature sensing functions within a single package for high performance air quality measurement. Parallax Inc. places the BME680 on a compact PCB with a 6-pin male header. This capable sensor does not have to be difficult to use. The BME680 is supported by BlocklyProp visual programming as well as C libraries for the Propeller multicore microcontroller. Code for other controllers is available from the Bosch Github repository.
-
product
Debug Adapters
One thing is sure in the life of an embedded developer - your next microcontroller development board will be fitted with a different debug connector to the one used in your previous design.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will pl...show more -
product
Distortion Detector PLUS
DD-1+
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment. Sets audio system gain overlap, continuously variable from 0.0dB - 15.0dB in 0.1dB steps Checks gain overlap of an audio system without making any adjustments to the existing settings Verifies that the gain overlap of an install hasn't been tampered with after install Features our Patent Pending Distortion Detection system plus digital microcontroller and our proprietary firmware
-
product
Signal Conditioning & Control
Offering a wide variety of products from amplifiers and comparators to redrivers, microcontrollers, data converters (ADC) and digital potentiometers (POTs).
-
product
SparkFun SAMD21 Development Board
RedBoard Turbo
If you’re ready to step up your Arduino game from older 8-bit/16MHz microcontrollers, the SparkFun RedBoard Turbo is a formidable alternative. At its heart, the RedBoard Turbo uses the ATSAMD21G18, which is an ARM Cortex M0+, 32-bit microcontroller that can run at up to 48MHz. With an impressive 4MB of external flash memory and a UF2 (USB Flashing Format) bootloader, the RedBoard Turbo provides you with an economical and easy to use development platform if you're needing more power than the classic RedBoard.
-
product
Development Boards
Everything From Full-Featured to Tiny Starter Boards. Professional, full-featured development platforms, rich in modules. Each Easy Board features on-board programmer or debugger, and supports an entire family range of microcontrollers.
-
product
Absolute Optical Encoder
A2
Product DescriptionRestriction of Hazardous SubstancesThe A2 absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2 reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintai...show more -
product
Hardware Debug Interface & Stand Alone Programmer
Cyclone PRO
P&E Microcomputer Systems' Cyclone PRO is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale HC08, HCS08, HC12, HC(S)12(X), and RS08 microcontrollers. Now featuring support for Freescale's ColdFire V1.
-
product
SparkFun RGB And Gesture Sensor
APDS-9960
This is the SparkFun RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and Gesture Sensor you will be able to control a computer, microcontroller, robot, and more with a simple swipe of your hand! This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price.
-
product
AC Hipot Testers
VLF
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Programmable micro-controller• Advanced digital frequency technology• Built-in printer• Portable• AC HIPOT testing of cables and electrical apparatus is now easier than before• UDEY VLF testers are suitable for testing cables, transformers, switchgear, rotating machinery, & other electrical apparatus.
-
product
SparkFun MicroMod RP2040 Processor
The SparkFun MicroMod Pi RP2040 Processor Board is a low-cost, high-performance board with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. With the MicroMod M.2 connector, connecting your MicroMod Pi RP2040 Processor Board is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards).
-
product
Electricity Metering Device- Residential
ES-12B
Designed for the residential smart meter rollout in Great Britain, this 5 terminal single phase electricity meter is an addition to our range of SMETS2 compliant solutions.With two 100A main disconnect relays, dedicated secure microcontroller and multiple communications interfaces including Zigbee and DLMS, the ES-12B is accurate and can operate in prepayment mode.
-
product
Cross Development Tools
S12Z
Cosmic's tool chain for the S12Z family is part of a complete and uniform product line incorporating over 20 years of innovative design and development. Cosmic's familiar and easy to use software interface is available for all Freescale microcontrollers to simplify the migration between targets. All Cosmic products include one year of technical support and updates.
