-
Product
JTAG USB Controller
NetUSB-1149.1/E
Controller
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
Product
8 Channels, RTD Measurement
RT1
-
The module provides 8 measurement channels, and can be programmed for interfacing to 2, 3, and 4-wire platinum RTD sensor configurations. The 4-wire mode (default) is the most accurate, providing excellent stability and repeatability. The RTD channels feature individual A/D converters and precision excitation/current drive. Programmable lead-wire compensation is provided for inherently less accurate 2 and 3-wire configurations. All RTD channels are self-aligning because each channel is automatically "aligned" on a rotating basis to eliminate offset and gain errors throughout the operating envelope. Programmability for expected resistance range and wire modes allows for optimization of scaling/resolution, as well as flexibility in reading many RTD types.
-
Product
Timing, Logic & Memory
-
Offering an extensive portfolio of products for programmable clocks, clock generation and distribution, standard logic and memory (Flash, EEPROM and SRAM) across various applications.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-224-HI
Programmable Resistor Module
The 40-230-224-HI (PXI) and 42-230-224-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 6.97kΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2502
Multifunction I/O
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
Super Fast Gang ISP Programmer
448Pro2
-
The Dataman 448Pro2 is a super fast PC based gang programmer with four independent 48-pin ZIF sockets, ISP capabilities and USB 2.0 connectivity • Up to 75% faster programming of high-capacity memory devices • Over 105,000 devices supported with new devices added monthly • Independent modules supporting concurrent programming • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Full ISP capabilities including JTAG compatibility • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
Product
USB Reusable Data Logger
-
Single channel, internal sensor for ambient air temperatureUser Programmable: manual or automatic start, sample interval, alarm limits, data tagsLarge, easy to read LCD displayRemaining Battery Indicator (low battery)Trip history statistics available on LCDNIST traceable and CE MarkUSB Connection
-
Product
AC to AC Programmable Power Sources
AFV-P Series
-
Rating:600 VA to 5 KVASingle Phase OutputOutput frequency: 45 Hz to 500 Hz (Optional for 15 Hz to 1000 Hz)
-
Product
2-Module ICT System, I317x Series 6
E9902G
In-Circuit Test System
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
Product
PXI Digital IO
-
The Keysight M9187A Digital I/O provide static digital input and output channels which can be used in applications that require the monitoring of digital states and the controlling of external devices. These are typically used in aerospace/defense, automotive, and electronic test applications. The module offers configuration flexibility with programmable input thresholds and flexible output drive capability.
-
Product
Electromechanical Programmable Attenuators
-
BroadWave manufactures single section 6 dB to 8 section 0 – 127 dB programmable attenuators. •Voltage control and external TTL control •RF Connectors: BNC, N, SMA and TNC •50 and 75 Ohm
-
Product
Envinronmental Chambers
-
MRC environmental test chambers with temperature and humidity control. Chamber Test Humidity and Temperature Programmable humidity and temperature of range full a simulates freezing, climatic, durability, reliability test to conditions .etc endurance thermal, assurance quality.
-
Product
USB JTAG controller
-
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
Product
Programmable Multifunction Generator
IST 5800/5850
-
IST Information Scan Technology, Inc.
The IST-5800 series programmable multifunction generator is an exceptionally versatile and economical instrument for applications in R&D, Manufacturing Test, Service Repair and Training. Featuring an adjustable triple output power supply and waveform generator, it has the ability to provide power and signal sources for a circuit while the universal logic probe, auto-ranging frequency counter, and digital voltmeter allows you to simultaneously analyze and measure circuit activity.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 3.55kΩ
40-298-023
Programmable Resistor Module
The 40-298-023 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Linear Power Supplies Programmable, Local or Digital Control, Ultra Low Ripple/Noise
Series MBT-G
-
Kepco's MBT-G series (denoted by suffix "G") are bench-style instrumentation power supplies that offer a choice of control methods including direct entry keypad, slew up/down keys, rotary controls and three communications ports: IEEE 488.2, RS 232 and Kepco's single address, multiple instrument long range serial bus. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm
40-294-012
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
UltraZed PCIe Carrier Card for UltraZed-EG System-on-Module
AES-ZU-PCIECC-G
-
The UltraZed PCIe Carrier Card supports the UltraZed-EG System-on-Module (SOM), providing easy access to the full 180 user I/O, 26 PS MIO, and 4 PS GTR transceivers available from the UltraZed-EG SOM via three Micro Headers. Two 140-pin Micro Headers on the carrier card mate with the UltraZed-EG SOM, connecting 180 of the UltraZed-EG Programmable Logic (PL) I/O to 2 Digilent Pmod™ compatible interfaces, FMC LPC slot, LVDS Touch Panel interface, push button switches, DIP switches, LEDs, Xilinx SYSMON, and clock oscillator.
-
Product
IF Digital Processing Board for Demodulation and Combining
LS-35-R
-
The Lumistar LS-35-R is part of the Lumistar family of digital processing boards used for programmable telemetry systems. The LS-35-R consists of a digital processing main board with two high capacity Xilinx Virtex-5 arrays. The LS-35-R provides a two-channel IF Receiver with Pre/Post detect combining, multimode demodulators with data rates up to 40 Mbps, bit synchronizer outputs, Viterbi decoding, spectral and constellation display, BER reader display and 70 MHz IF modulator with calibratednoise feature. The all-digital design assures a consistent product with high reliability and long-term stability.
-
Product
Ethernet POE & PHY Testing
-
Networked Communication Solutions, LLC
A multi-port programmable load.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2Ω to 13.6kΩ
40-251-131
Programmable Resistor Module
The 40-251-131 is a programmable resistor module with 2 channels which can be set between 2Ω and 13.6kΩ with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-122-HI
Programmable Resistor Module
The 40-230-122-HI (PXI) and 42-230-122-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
-
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
Product
Standardized Bus Interface
IP-429-II
-
Connect to your Avionics with IP-429. Pick 2,4,6,or 8 ARINC 429 compatible receivers and 1, 2, 3, or 4 transmitters. Transorb protected IO. Software programmable transmit rates [100K or 12.5K]. Time Tag on received data. IndustryPack campatible with 8 or 32 Mhz. bus operation.
-
Product
50W Power Supply, 8V, 5A or 20V, 2.5A
E3642A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 50W, single output E3642A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
Product
PCIe Mini Module
PCIe-Mini-SYNCHRO
Controller
The PCIe-Mini-SYNCHRO module is a one channel Synchro/Resolver controller. It uses a state of the art 16-bit monolithic Resolver-to-Digital converter. This single chip converter offers programmable features such as resolution, bandwidth, velocity output scaling and encoder emulation.
-
Product
MIL-STD-1553 PMC Interface Module
PMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 3Ω to 11.4MΩ
40-251-053
Programmable Resistor Module
The 40-251-053 is a programmable resistor module with 2 channels which can be set between 3Ω and 11.4MΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXIe 8 Bit High Speed DIgitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4X.2211-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 1.5Ω to 3.55kΩ
40-252-123
Programmable Resistor Module
The 40-252-123 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 3.55kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
