Showing results: 406 - 420 of 480 items found.
-
MVR Series -
Innovative Technical Systems
The MVR Series of Muzzle-Velocity Radars are Doppler-CW transceivers that measure the velocity of viewed objects such as projectiles. They use phase-locked millimeter-wave transmitter-receivers along with an integrated radome-protected antenna to illuminate objects under investigation. An optical boresighting aid provides alignment assistance for the narrow radiation patterns. Reflected signals from the target are received by the antenna and mixed to produce a video output equal to the Doppler spectrum of the target. A low-noise, variable gain video amplifier can drive a 50-ohm cable up to +1 volt output. The video amplifier has a feed-forward DC offset compensation circuit that extends the Doppler frequency response from under 1 Hz to over 2 MHz. An integrated DMM and LCD display on the front panel monitors various test points within the sensor to verify proper operation. The extremely rugged design allows the MVRs to withstand high acousitic shock environments so they can be located in close proximity to the projectile source.
-
Fairview Microwave Inc.
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
NI
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Labtone Test Equipment Co., LTD
Labtone EV series of electrodynamic shaker vibration test System simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications.Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.Labtone EV series of electromagnetic vibration testing system is specially designed to meet the need for long time operation. Vertical and horizontal vibrations can be achieved by the installation of vibration resistant base. The standard platform is equipped with high efficiency airbag shock isolation device, so that the vibration transmitted to the building can be minimized. There is no need for additional foundation in most of the cases.A complete set of vibration testing system is composed of shaker, power amplifier and vibration measuring control system, in accordance with the relevant national and international standards (such as: MIL-STD, DIN, ISO, ASTM, IEC, ISTA, GB, GJB, JIS, BS, etc.) to provide technical support for establishing product quality inspection.
-
cPCIS-2500 Series -
ADLINK Technology Inc.
The cPCIS-2500 series 3U CompactPCI 6-slot Cubic Chassis is designed for 3U CompactPCI cards and modules without rear I/O. It is 4U in height, 237 mm deep, and suitable for bench top use or wall mounting. It is ideal for industrial or transport applications where small chassis size and versatility are important. A built in cooling system with removable filter provides maximum cooling efficiency, and the 250W cPCI power supply allows easy maintenance. The cPCIS-2500 series' ability to handle a wide range of temperatures and excellent shock and vibration characteristics make it suitable for operating in a rigorous environment.
-
ADLINK Technology Inc.
ADLINK products include the most rugged offerings in the industry, Single Board Computers (SBC) in popular compact form factors for embedded applications, and rugged systems with field-proven reliability, durability, and performance. PC/104 family products provide unmatched fanless operation over temperature extremes, resistance to shock and vibration, conformal coating, embedded BIOS, and a long product life reputation. The products continue to distinguish itself as an Extreme Rugged product for a multitude of applications. Mini-ITX embedded boards support the latest processors to deliver a high performance and space-saving platform for a wide array of embedded computing applications.
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Oscilloscope for transient vibration signals*Displays the time response of vibration acceleration and VM-SCOPE+ also for velocity and displacement*Suitable for shock and drop testing of packagings and other products *Memory for 110 s post-trigger and 1 s pre-trigger real time signal recording*Two measuring cursors*Export function for bitmap and text*Up to four signals per window*One VM-SCOPE license can be operated simultaneously up to four times with different settings *Measurement of decay time*Measurement of HIC (Head Injury Criterion)*VM-SCOPE may trigger the frequency analyzer module VM-FFT*External Messengers *Offline measurement
-
Smiths Interconnect
The proprietary MicroClip™ is a low-profile, low-mass spring loaded mechanical assembly that offers a rugged optical connection that is resistant for shock and vibration and is suitable for harsh environment. The MicroClip ferrule design has proven it can withstand a 1 kg live traffic fiber pull test on a 12-fiber ribbon cable pigtail mated to its LightABLE™ products (40G SR4 and 120G SR12), without any signal performance degradation. This result exceeds by a factor of 2 the requirements of Telecordia GR-468-CORE Fiber Integrity Side Pull Test and confirms the reliability of the Reflex Photonics fiber ribbon interface with the LightABLE and its MicroClip ferrule.
-
SafEye (Quasar 900) -
Teledyne Gas & Flame Detection
The Open Path Combustible system detects hydrocarbon gases by analyzing the absorption of radiation caused by gases in the atmosphere and comparing it to background atmospheric absorption. This is accomplished between a pair of units: a Flash Source and a Detector that can monitor a distance of up to 200 meters.Open Path Combustible Gas Detectors are robustly designed and can handle the toughest environments: 316L stainless steel housings that meet IP66/IP68 and NEMA 250 6P egress standards; circuit boards epoxy coated for protection; MIL-C-810C testing for humidity, salt, fog, vibration, mechanical shock and temperature extremes; and SIL-2 approval per IEC61508 is a final statement in reliability.
-
Advantech Co. Ltd.
Advantech UTX Gateway System providess Mini ITX bundled with the Intel IoT Gateway Solutions for Internet of Things (IoT). UTX is 4.4" x 4.6" with max. Connectivity, low power consumption with wide temp. And fanless design in a palm size motherboard. UTX embedded system is an industrial-grade system in a 4.6"(L) x 5.6"(W) x 1.4"(H) box. Cable-less & Wide-temp -20~ 60C design for fast integration and shock resistance. UTX is also easy to implement for industrial computer as embedded computer. UTX Systems are ideal for POS, digital signage, transportation, portable medical devices and industrial automation.
-
213 HVD~226 HVD -
Standard Electric Works Co., Ltd
● Excellent shock resistance.● Rugged nylon moulding.● Auto on (when voltage detected).● Excellent drop resistance.● Good vibration resistance.● Loud sound alarm indication.● Built-in proving and self-test circuit.● High bright color-coded LEDS.● Works from standard 9V battery.● Interchangeable contact electrode.● Use in all whether conditions.● Compatible with all link sticks.● Lightweight, robust & compact.● Models available from 11kV to 132kV.● Suitable for indoor and outdoor use.● Self(auto on) or manual arming.● Easy access to batteries.● Customized threshold on demand.● Auto off (if no voltage detected).● Waterproof design, protection class : IP65.
-
785854-01 -
NI
The FD-11614 measures up to 16 thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11614 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11614 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11614 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
P55 -
Validyne Engineering
The robust P55 pressure transducer provides cost-effective reliability for severe test environments. With extreme resistance to shock and vibration, the P55 pressure transducer delivers the same high-level performance expected from more delicate differential pressure transducers and pressure transmitters. With variable reluctance sensing technology, the P55 pressure transducer delivers fast dynamic response, high resistance to vibration and superior signal stability through ambient temperature change for a wide variety of low-pressure to high-pressure measurements. The P55 pressure transducer will accept both liquids and gases directly at the sensing diaphragm and there are no internal isolation fluids to slow the sensor response or cause excessive temperature drift errors.
-
Extech CT70 -
Extech Instruments Corporation
Circuit and wiring issues can introduce shock hazards and compromise performance of machinery and equipment. The CT70 is a GFCI and AC circuit analyzer which covers outlet load handling and outlet tester functions. AC load tester functions cover selectable loads of 12, 15, and 20 Amps; loaded and unloaded AC line voltage measurements; voltage drop/line impedance calculations; and peak line voltage. Outlet tester functions include neutral to ground voltage; hot, neutral, and ground impedance; GFCI trip time/trip current; and open or reversed wiring. The CT70 comes complete with AC test cord (standard North American 3-prong plug).
-
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
