Precision Current Sources
-
Product
Suitable For Current Or Voltage Process Signals
SEM1600VI
-
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Resistive Current Tester
-
Weshine Electric Manufacturing Co., Ltd
Long Distance Digital Zinc Oxide Arrester Resistive Current Safety Testing Set
-
Product
TMR Current Sensors
-
MultiDimension Technology Co.,Ltd.
An open-close current transducer, high sensitivity and signal-to-noise ratio TMR chips are used in the design, which based on Tunneling magneto resistance effect. The transducer has a built-in temperature compensation and nonlinear compensation circuit, which can accurately measure DC, AC and pulse current. The transducer has many benefits ,such as high precision, wide bandwidth, low power consumption, excellent isolation performance and so on. Besides, the design of open-close structure makes it easier to install and unload.
-
Product
Precision Resistor Network
-
Analog Devices provides a portfolio of quad resistor networks with excellent matching specifications over the entire temperature range. All of our resistors can be accessed and biased independently, making them a convenient and versatile choice for any application that can benefit from matched resistors. Our resistor networks provide the precise ratiometric stability required in highly accurate difference amplifiers, voltage references, and bridge circuits.
-
Product
Controllable, Programmable Linear DC Source
LAB / S
-
*Linear laboratory power supply*High quality DC sources with the lowest residual ripple*CV / CC mode with LED display*Protection against short circuit, overload and overtemperature*Optional IEEE 488, RS232, analog interfaces*3-phase input optional
-
Product
Precise Timing Measurement
LED-Panel
-
Image Engineering GmbH & Co. KG
This is the ideal measurement device to determine shutter and shooting time lag, autofocus time, burst frame rate and the exposure times of digital imaging devices.
-
Product
Split type AC Current Sensor
CTF-5A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of terminal feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
Current Probes
-
PMI® introduces the convenience of flexible current probes (Flex CTs)! These 5,000A probes come in 12″, 24″, 36″, and 48″ lengths that allow you to easily surround multiple conductor bundles. They are available in sets of two, three, or four for use with different recorders. The Flex CTs are powered from recorder voltage and DO NOT require a battery pack for operation.
-
Product
Tunable Laser Source Module
-
Keysight's has a wide range of tunable laser sources to fit your needs for various applications. In addition to the proven 81600B tunable laser source family, Keysight recently introduced a new family of tunable laser sources - the 8160xx family. The 8160xx tunable laser sources offer the full wavelength range from 1260 nm to 1650 nm with no wavelength gaps. All 8160xx tunable laser sources are modules for the Keysight 8164B lightwave measurement system mainframe. This provides test instrumentation with maximum flexibility. Investing in the Keysight 8160xx family of tunable laser sources can realize the cost efficiency and performance required to test components for coarse and dense wavelength division multiplexing (CWDM, DWDM) and passive optical networks (PON).
-
Product
Current Injection Sets
-
Built in c based Time Interval Meter measuring from1 millisec to 9999 sec. Panel with easy and clear legends to read. Continuosly variable outputs. Auto Cut-off & output isolated. Self sensing of contacts i.e. NO or NC Potential free star stop signals Available in Portable / Lab type models with metal cover
-
Product
HCAI-1 High Current Arc Ignition Tester
HCAI-1
-
The HCAI-1 High Current Arc Ignition Tester is according to IEC 60950-1:2001, BS EN 60950-1:2001, BS 7002:2000, GB 4943.1-2011
and UL746A, IEC60947.1: 1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-2008 and other standards required simulated safety test project. Parts and components of insulating materials or other solid combustible materials that are prone to flame spread in electrical and electronic equipment may ignite due to proximity or contact with electric arc, causing electrical fire and endangering the reliable operation of equipment and personal safety. -
Product
Integrated Two-Stage Current Sensors
-
If ultra-low noise performance is required, our integrated two stage devices are the number one choice. With input inductances from 24 nH to 1.8 µH and a flux-noise level as low as 0.8 µPhi0/sqrt(Hz) an energy resolution of about 45 h is attained. The devices consist of a 16 SQUID series array as amplifier stage and a single front-end SQUID.
-
Product
Primary Current Injection Kits
-
During installation,testing,especially if the protective gear is connected to the power line via a current transformer it is advisable to use our Primary Injection Test Set. Keeping this in mind a wide range of Primary Current Injection Test Sets are being manufactured by "NMC”.
-
Product
Mode-Conditioned Light Sources
-
Thorlabs' Mode-Conditioned Light Sources are fiber-coupled LED sources that have an output with a flat-top profile in the far field. Common applications include the testing of multimode fused fiber components as well as verification of modal behavior in fiber-based setups. Standard fiber-coupled LED sources can have a range of output profiles that are usually not uniform and vary from source to source. This can be dependent on emitter orientation, alignment with fiber tip, and connector assembly. These mode-conditioned sources have been engineered to distribute light evenly into all transverse modes, resulting in an equilibrium modal distribution at the output. The front panel includes an adjustment knob to control the power and an output port that accepts 2.2 mm wide-key FC/PC connectors. A DS15 15 V power supply with a location-specific plug is included with each device.
-
Product
Current Probe For Non-Intrusive Measurement Of AC, DC, And Waveform Currents
CP 305
-
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
Product
Optical Laser Source & Power Meter
-
Shanghai Grandway Telecom Tech. Co., Ltd
Grandway provide a variety of optical network testing instruments to play a stable performance in the process of optical network construction and maintenance.
-
Product
DC/AC High Current Probe
698
-
Unit is designed for use with digital multimeters,lab scopes or graphing meters. With 1000 Amp capabiltiy, this instrument can be used to test starting and charging systems. It can even be used to test relative compression when used with your lab scope or graphing meter.
-
Product
Precision Barometer
HD3114B
-
Temperature, humidity and pressure handheld data logger with color graphic LCD display.
-
Product
12DO(Source Type) Modbus RS-485 Remote I/O
ADAM-4056SO
-
12ch source type digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system5000VDC isolation protection
-
Product
PXI Precision Resistor Module, 4-Channel, 2 to 6.97k
40-297-130
Programmable Resistor Modules
This 4-channel PXI precision resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
ANSI Relaying Current Transformer Burden
-
The ANSI Current transformer burden is designed for loading the current transformer during accuracy Tests. The ANSI burden is designed as per ANSI burden C57.13.It can be used along with the Eltel Automatic Instrument Transformer Test Set to test CTs as per ANSI Standards.
-
Product
Auxiliary Current Transformers
-
Osborne Auxiliary Current Transformers are often used to reduce system currents to lower values appropriate for instrumentation and/or protection circuits. The Aux CT’s are designed for specific current ratios and burden impedance with a known transformation error. Osborne’s units are built for high performance and longevity in the most demanding environments.
-
Product
Primary Current Injection Tester
SLQ
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
It's a high voltage generator insutrment for tesitng.
-
Product
Time, Current, And Resistance Meter
-
AllWin Instrument Science and Technology Co., Ltd.
1. Time, current and resistance can be displayed simultaneously2. Out put current:5~30A. Ground resistance range: 50~600 mohm
-
Product
20 Amp Current Transformer Burden Test Set
1044A
-
Due to overwhelming demand, TESCO is pleased to re-introduce the 1044A 20 Amp Current Transformer Burden Test Set. This light weight, hand held unit is a simple and inexpensive means whereby a current transformer installation may be quickly checked for many sources of trouble. The 1044A provides utilities a less expensive and more traditional option for checking larger services for potential meter circuit related issues.
-
Product
Low Noise Current Preamplifier
SR570
-
Stanford Research Systems, Inc.
The SR570 is a low-noise current preamplifier capable of current gains as large as 1 pA/V. High gain and bandwidth, low noise, and many convenient features make the SR570 ideal for a variety of photonic, low temperature and other measurements.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-036
Programmable Resistor Modules
The 40-297A-036 (PXI) and the 42-297A-036 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 395 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Pulsed Source Measure Unit
-
The SpikeSafe SMU is a precision pulsed source measure unit that precisely sources pulsed current and simultaneously digitizes voltage. Optimized for precise and repeatable high-power LED and laser testing, SpikeSafe™ SMU (Source Measure Unit) current sources deliver precise pulsing with low microsecond rise times, low-jitter triggering and integrated digitizer for more accurate and repeatable high-power LED and laser testing.
-
Product
Single-point Current Meter
-
The SEAGUARD® is the core module used in small and medium sized underwater observatories. Whether used as a multipurpose instrument, or as a hub for strings in the water column, the SeaGuard manages connected sensors and the real-time communication of data and meta-data to shore. In autonomous configurations, long battery life is achieved with aggressive power routines keeping the full system at the lowest power levels possible.
