Power Loads
-
Product
Load Cells and Sensors
-
AMETEK Sensors, Test & Calibration
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.The full bridge load cells and sensors provide high precision measurements that ensure adherence to the international standards.
-
Product
Load Cell Measurement Interface
LCIC-1106a
-
Industrial Measurement Systems Ltd.
Any application related to weighing or measuring forces is now available in your PC...Stand-alone microcomputer-based interface card requires no other interfacing accessories. Simply connect th
-
Product
RF Coaxial Load
-
RF Lambda’s coaxial loads are used to terminate RF signal chain to provide a good 50ohm match and dissipate any excess RF energy. They are available in a variety of power levels and offer low VSWR.
-
Product
Modular DC Electronic Load
63600
-
Chroma Systems Solutions, Inc.
Chroma’s 63600 Modular DC Electronic Load is designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, adapters, and power electronic components. They are excellent for use in research, development, production, and incoming inspection applications. The 63600’s state-of-the-art design uses DSP technology to simulate non-linear loads using an unique CZ operation mode allowing realistic loading behavior.
-
Product
EPM-P Series Single Channel Power Meter
E4416A
Power Meter
The E4416A single channel EPM-P series power meter, for peak, average, peak-to-average ratio and time-gated measurements, using the E9320 peak and average power sensors.
-
-
Product
Heat Exchangers RF Coaxial Loads
86500 Series
-
The 86500 Series Heat Exchangers are ideal for areas where water is limited. The loads are rugged, self-contained, easily operated, and portable units capable of dissipating up to 80 kW of RF power from DC to 800 MHz with a VSWR of 1.10:1.
-
Product
DC Loads
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik offers wideband multichannel DC decouplers for antenna diagnostic applications. Due its high bandwidth the device is suitable for all broadcast, cellular and Wi-Fi standards.
-
Product
Signature Compression Only Load Button Load Cells
SLB SERIES
-
The SLB Series Subminiature load cells (Load Buttons) are offered for compression only applications where space is limited. The matching surface must be flat for ultimate accuracy. The loading diameter is slightly convex for accurate load distribution. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
Product
Channel Load Generator
802.11p
-
Qosmotec Software Solutions GmbH
When many cars are equipped with 802.11p communication technology, high traffic density will also cause significant load on the radio channel. From normal wireless communication systems it is a known problem, that many users can cause a complete breakdown of the network. Car-to-X communication technology tries to protect itself against those kind of breakdown by a carrier sensing mechanism: Each communication device has to check first, if the radio channel is busy. In that case, it waits for a random delay to avoid packet collision on the radio channel, which causes a loss of both collided packets.
-
-
Product
Phantom Load Test Set
-
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
Product
Thermal Load Boards
-
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
Product
Artificial Phantom Load with Power Factor
RC-50
-
The RC-50 Artificial Phantom Load has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges. Features: Artificial Load, Light Weight, 50 Amps, 50% Power Factor.
-
Product
Load Cells
-
Flintec load cells are highly accurate and built to last. We pride ourselves on the quality of our products and the service we provide.Our sensors are available globally. If your application requires a Custom Solution, our expert engineers can help.
-
Product
Dual Range Switching DC Power Supply, 3 Output, 0 V, 60 V, 0 A, 3 A
T3PS36006
DC Power Supply
Dual Range Switching DC Power Supply, 3 Output, 0 V, 60 V, 0 A, 3 A.
-
Product
Coaxial Terminations (Loads)
-
Keysight offers a variety of coaxial terminations (loads) solutions to terminate up to 75 Ohm coaxial systems with precise, low reflection loads for superior RF performance.
-
Product
AC Load Bank (Resistive/Capacitive)
K-1000 Resistive/Capacitive
-
Kongter Test & Measurement Co., Limited
A RCD (resistive/capacitive) generator load bank is non-linear load bank. The electronic and non-linear loads simulated by capacitive load banks are typical of the Telecommunications, Computer or Uninterruptible Power Supply (UPS) Industries.
-
Product
Interface And Load Box
MS 3646I
-
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
-
Product
Power Measurement
-
Precision Acoustics manufactures Radiation Force Balances and Check Sources which can be used to measure ultrasound power according to the IEC Standard 61161. All products are supplied with a calibration from The National Physical Laboratory, LONDON.
-
Product
High Precision Electronic Load
PEL-8000
-
PEL-8000 series adopts high-performance chip high-speed and high-precision design, providing resolution of 0.1mV, 0.01mA (basic accuracy is 0.03%, basic current rise rate is 2.5A / US)
-
Product
Hand-Held/Digital Load Tester
6030DV
-
• Full 125 Amp load Tests 12 Volt and 24 Volt batteries (DUAL LOAD) alternators and starters on all types of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
6.5-Digit Low Noise Power Source, 32 W, 210 V, 3 A, 2-Channel
B2962B
Low Noise Power Source
The Keysight B2961B Series 6.5-digit low noise source power supplies provide a power supply and source solution that meets the difficult measurement challenges researchers, designers, and developers face working on advanced components, circuits, and materials.
-
Product
Isolated DC Power Supply for PC104-PCI Express Embedded Applications
EXC-PSM104PCIe
Power Supply
The EXC-PSM104PCIe is an isolated DC power supply specifically designed to provide reliable power for highly demanding PC104-PCI Express embedded applications. The EXC-PSM104PCIe has a wide input voltage range while providing robust and reliable power for embedded and industrial motherboards. The power supply is also fully compliant with MIL-STD-704A and E, MIL-STD-1275B and MIL-STD-461E.The EXC- PSM104PCIe has totally independent safety features including input undervoltage lock-out, output overvoltage protection, output current limit protection, and temperature protection. Additionally, the Soft-Start function limits inrush current during startup.
-
Product
Rad Hard Load Switches
-
Renesas' radiation hardened load switches provide a simpler and smaller way to turn on and off your power rails in multi-rail power systems compared to a discrete FET. Load switches are also ideal for redundant power distribution, power sequencing and input-output protection of POL based power distribution systems.
-
Product
4kW Electronic Load
PT04-110
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 110V and 48V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
High Power DC Electronic Load
63200A series
-
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
-
Product
10 MHz to 50/53 GHz USB Wide Dynamic Range Average Power Sensor
U2055XA
Power Sensor
The Keysight U2055XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz USB average power sensor.
-
Product
Power Meter
EPM 6000
-
EPM 6000 is the industry's highest performance revenue grade panel meter. Based on the latest technology and an all new platform, EPM 6000 has a superior cost to performance ratio and significantly outperforms other metering products many times its price.
-
Product
Programmable DC Electronic Load
63000 Series
-
The 63000 Series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power suppl ies, A/D power suppl ies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices. The 63000 Series offers models in two operating voltages 150V models, with 250W and 350W power levels up to 60A in a single unit. Their compact and light weight design make these loads easy to move around which is ideal for R&D and design validation. Each model of the 63000 Series has unique user-def ined waveform (UDW) funct ion capable of simulating real-world custom waveforms. In addition, a data storage function has been built in for saving and recalling up to 100 stored settings at any time. For automated testing, these save and recall functions can save a great deal of time. The 63000 Series has 3 power ranges that can precisely measure the voltage and current in real time. Since short circuit testing is a critical test item, the 63000 provides short circuit simulation to effectively address application demands for power and automated testing.
