Impedance Testers
See Also: Loop Impedance Test, Impedance Analyzers
-
Product
Check-Point Circuit Tester
21000
-
Most widely used automotive circuit tester. Quickly checks all 6 and 12 volt systems. Use with power on. 48" ground wire. Use to locate shorts, grounds and open circuits.
-
Product
Automated Connector Tester
-
GCI's Automated Connector Tester is a self-contained test bench providing reliable testing of filtered and non-filtered electrical connectors. The ACT automates the tedious process of testing each pin against all others and shell for DC and AC leakage. For filter connectors, the ACT accurately measures pin-to-shell capacitance. For pins protected by diodes, the ACT provides leakage and breakdown measurements. The ACT also verifies pins which are intentionally shorted to each other or to the shell.
-
Product
HV Tester
-
For High Voltage withstand, breakdown testing of electrical insulating systems.For Dielectric Strength testing of electrical / electronic components, small appliances, tools, motors, machines etc.
-
Product
Wire Crimp Pull Tester (Manual)
WT3-201
-
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
Product
Scott Internal Bond Impact Tester
-
The Scott Internal Bond Impact Tester is used to determine tear resistance (Elmendorf). A sample is torn with the help of the pendulum device starting from a predetermined cut. The work required for a tear of a given length is measured.
-
Product
Course Length Tester
TF124
-
TESTEX Testing Equipment Systems Ltd.
Course Length Tester, to determine the accurate length of a complete course of knitted fabric. When the yarn is attached to the clamp and wound round the pulleys, the length indicated on the ruler by the weighted clamp is added to that indicated on the appropriate location in use to give the total length of yarn.
-
Product
Power Steering Tester in Storage Case
34650
-
Gives fast, accurate power steering analysis. Test for defects in power steering pumps, gears and lines. Large heavy duty gage reads from 0-2,000 PSI and 0-140 BAR. Use to rule out power steering problems before expensive suspension or steering linkage problem is attacked. Includes 13 adapters. Supplied with instructions in a durable, plastic molded storage case.
-
Product
Continuity Tester Supplied without Battery
22700
-
Use to test for continuity with power disconnected. Excellent for use on marine, recreational and general automotive vehicles. Test appliances and other electrical circuits with power off. 48" lead wire. Uses AA 1.5 volt battery (not supplied).
-
Product
Hamburg Wheel-Tracking Tester
-
The Hamburg Wheel-Tracking Tester is used to test submerged, compacted Hot Mix or Warm Mix Asphalt specimens as per standard.The device consists of a reciprocating wheel that is rolled over the specimens while measuring the rate of permanent deformation. A constant load of 705 N ±4.5 N is applied to the specimens with a sinusoidal wheel speed of 1 ft/sec in a constant temperature controlled water bath up to 70 °C (± 1.0 °C). An LVDT jig is used for continuous measurement of permanent deformation along the path of the rolling wheel. Accommodates cylindrical or slab specimensSoftware for automatic determination of Stripping inflection PointNumber of passes to SIP, number of passes to failure and other calculated parametersStainless steel construction with temperature controlled water bath up to 70ºC
-
Product
DIELECTRIC and CONTINUITY TESTERS ( HI-POTS )
AV-25V-GC1-05
-
This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test.
-
Product
Bobbin Winding Coil Turn Tester
SS108 Series
-
This (SS108** series) winding coil turn testers are used for testing turn of various coils without core, like as: generator winding, transformer winding, relay, inductor, contactor, ignition coil, voice coil, etc.
-
Product
FPD Tester Signal Module
A040209-05-04
Signal Module
A040209-05-04 is a MIPI signal module board and complies with the MIPI DSI v1.2 / MIPI D-PHY v1.1 signal specifications and standards. A040209-05-04 is used with the FPD Tester and can be applied to MIPI Display testing, providing MIPI Panel standard signal and other related controls.
-
Product
Universal Testers
-
All of our Universal Testers can be manufactured to utilize manual loading, manual loading with auto unloading, or automated load/unload. The interweaving of slip sheets between each PCB is available as well when utilizing an automated load/unload system.
-
Product
Fuel Injection Pressure Tester
33900
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
Product
Mic / Audio Line Tester
Qbox
-
Whirlwind Music Distributors, Inc.
The Qbox is the all-in-one audio line tester ideal for applications such as live sound, maintenance, installation work - anywhere audio runs down a cable. The Qbox can quick-check dynamic microphones and cables without firing up the entire system. It provides a handy mic or line-level tone for activating a signal path or identifying a specific cable in a pile of cable ends.
-
Product
Cable Tester
CableJoG 128
-
The CableJoG 128 can test up to 128 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection.
-
Product
Battery Crush Nail Penetration Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL battery crush nail penetration tester is used to simulate the use, transportation, storage and disposal of various types of batteries under certain temperature conditions, when the battery is crushed (such as compacted garbage) or nail penetration, and to judge the battery safety performance. The battery is qualified as no disintegration, no rupture, and no fire.
-
Product
Bond Tester
Sigma
-
Sigma is the most advanced bond tester. It comes with game-changing automation capabilities and high specifications
-
Product
Single-Functional Testers
-
Electrical installation safety testing is a wide subfield of general electrical safety testing and encompasses both troubleshooting and fault-finding in complex industrial installations and simple, often periodic testing of only specific parts of the installation. The former usually requires the use of multifunctional testing devices, while the latter can be more conveniently done by testers with far fewer test and measurement functions.
-
Product
Catena 1910 HSIC Tester
Catena 1910
-
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
Product
2D Color Temperature Tester
LCC-900
-
Screens the pass/fail results or module type LED image information that is automatically reset via data transfer with handler unit. Data results are stored in server for unified management.
-
Product
Module Breakage Tester
MBT
-
The tester is used to provide confidence that the risk of physical injuries can be minimized if the PV module is broken in its specified installation. The module breakage test is specified in the IEC 61730 (MST 32).
-
Product
Specialty Testers
-
Klein Tools has a wide range of specialty testers, each designed to meet the needs of specific trade professionals. All testers are engineered to give the most accurate readings possible while standing up to the tough jobsite conditions encountered by tradespeople every day.
-
Product
Heavy Duty Diesel Compression Tester
DCT1570
-
Compression tester and adapters to test many vehicles, trucks, heavy-duty equipment. Covers Cummins, VW, Volvo, Allis-Chalmers, Bedford, I.I.Case, John Deer, IH, Mack, Massey-Ferguson, Mitsu-Fuso, Scania, White Farm, Detroit Diesel, and more.
-
Product
Compact Tablet Hardness Tester
HC 7
-
The new member of our Lab.line product family: the HC 7 hardness tester for manual use in the laboratory.Equipped with a touch display and the new database-driven touch software, the HC 7 impresses with its exceptional user-friendliness. The new software can be operated intuitively and is equipped with all important functions for quick operation.Start your quick, direct and product testing with just a few clicks directly via the touch display and set up to 50 products. Reports can be printed externally via USB or LAN interface. It is also possible to connect DYMO* and EPSON* roll printers (*special models only).
-
Product
Battery Cell Surge Tester
Chroma 19311
-
Chroma Systems Solutions, Inc.
The 19311-10 has 10 channels, which can test up to 9 battery cells via scanning test, with a single unit. It can support up to 25 channels for testing up to 24 cells in a sequence by connecting with an external scanner (A190362). The test speed of the multicell scanning test by 19311-10 is extremely efficient, saving test time, and decreasing labor costs. It also increases the production capacity of the production line.
-
Product
Wideband Radio Communication Tester
CMW500
-
The R&S®CMW500 wideband radio communication tester is the universal test platform for RF integration and protocol development. It is available as the R&S®CMW500 callbox and the R&S®CMW500 protocol tester. The R&S®CMW500 includes a fully integrated end-to-end data solution that permits comprehensive IP throughput and quality measurements. Thanks to the internal fading simulator, it is easy to perform tests under realistic propagation conditions.
-
Product
Transformer Performance Tester
JYM
-
JYM insulation resistance tester is used for on-site insulation resistance measurement. The instrument has built-in positive and negative bipolar high-voltage power supplies, with large output power and strong load capacity. It is suitable for insulation resistance measurement of samples with large capacitance, such as power transformers and cables.
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
Flexing Tester
-
Premier's Flexing Tester are used to check how much the bending movement of the cord influences the electrical and mechanical connection.
