-
Product
Personal SerDes Testers
C Series
-
Everything you need to develop and verify your high-speed digital algorithms is contained in these ultra-portable test instruments. They will forever change the way you think about developing and verifying Gbps digital and mixed-signal algorithms, and they will allow you to measure signals in ways that were not possible in the past. Each personalized SerDes tester is equivalent to multiple hardware platforms, containing everything that you need to make high-performance measurements like bit error rate testing, signal generation, and signal measurement.
-
Product
Winding Resistance Tester
JYR-50C/40C/20C
-
1. With demagnetization function.2. Testing range reach to 20k3. Also apply to testing tranformer with high winding resistance.
-
Product
Component Testers
-
After a wafer is tested through front-end test and back-end test, the component tester tests this final component or package assuring its quality for the semiconductor makers. DDR, DDR2, DDR3 memory component testers.
-
Product
New CCA Tester
BTT-02
-
Hangzhou Xun Anda Electrical Co., Ltd.
Passive testing method is safe.Never discharges or drain the battery.Able to test condition of discharged battery.Consistent and repeatable results.
-
Product
Shoe Flexing Tester
UI-FT29
-
Shoe Flexing Tester is suitable to test complete shoe flexing resistance ability as per SATRA TM92. It is suitable to test all kinds of shoes and can be used to for SATRA TM77. This machine can be made to test in low temperature. Besides, Shoe flexing & water penetration tester is available.
-
-
Product
Bench Mounted Tester
Flex 10
-
The Flex 10 bench mounted ATE is the smallest ‘standard’ tester in our range. The system comprises a single unit, measuring 600mm x 360mm x 660mm. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
Product
Wire Mount Testers
-
Is designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
Product
Deadweight Testers & Gauges
-
The most accurate instrument available for the measurement of pressure above a few psig is the Hydraulic Deadweight Gauge. This type of gauge operates on the principle of balancing a known mass against the force exerted by an unknown pressure on a piston of known area.
-
Product
WAN Tester
-
The Telinc WAN Tester is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, modems, multiplexers, CSU/DSUs, T-1 ESF CSUs, DU, NTUs and TIUs.
-
Product
ESD Tester
-
Tokyo Electronics Trading Co., Ltd.
Is performed to test the susceptibility of ICs and electronic devices to ESD.
-
Product
Portable Hardness Tester
Handheld Hardness Testers
-
Handheld Hardness Testers are ideal hardness testing tools where large samples, which cannot be brought to a traditional tabletop hardness tester, or specimens with hard to access areas are to be tested. A wide variety of the portable hardness testers, offered by Qualitest ensure that we recommend the most suitable model for your application. The extensive selection of our handheld hardness testers is available from low-cost economy models up to advanced models coming with more features. These models can measure the hardness of your materials in Rockwell, Superficial Rockwell, Brinell, Vickers, Webster, Barcol scales and often conversions can be done.
-
Product
Incline Impact Tester
KRD100 series
-
KRD100 series incline impact tester simulates the ability of product packaging to resist shock damage in the actual environment, such as handling, stacking of shelves, sliding of motors, loading and unloading of locomotives, product transportation, etc. This machine can also be used as a common test equipment for scientific research institutions, colleges and universities, packaging technology test centers, packaging materials manufacturing plants, and foreign trade, transportation and other departments to conduct incline impact test.
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
Insulation Resistance Tester
1507
-
The Fluke 1507 is a versatile, compact, handheld insulation tester for advanced industrial and electrical insulation testing. Its multiple test voltages make it the ideal tool for many troubleshooting, commissioning, and preventative maintenance applications.
-
Product
Fast Speed Models (PCI Cameras)
xiB 64
-
High-speed interface with a bandwidth of 64 Gbit / sec. CMOSIS sensor: CMV12000. Luxima sensors: LUX13HS, LUX19HS, LUX160. Gpixel sensors: GMAX0505, GMAX3265. Resolution from 1 Mpix to 65 Mpix. Speeds from 333 Fps to 3500+ Fps. Suitable for OEM customization and Embedded vision systems. Distances up to 300m over fiber-optic cable. Compact housing: 60 x 70 x 55 mm
-
Product
Brinell Hardness Tester
-
Using a carbide ball penetrator, and applying loads of up to 3,000 kgf, Brinell hardness tester following ASTM E-10 are widely used on castings and forgings. This method requires optical reading of the diameter of ball indentation, and using a chart to convert the average measurement to Brinell hardness value.
-
-
Product
FPD Tester Signal Module
A291800-03
Signal Module
The A291800 is an LVDS signal model that can be used with FPD Tester to provide LVDS panel standard signals and related controls for LVDS inspection.
-
Product
DC Vibration Unit Tester
BK2116
-
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
Product
Radio Communication Tester
CMP200
-
The R&S®CMP200 is an IF tester that combines vector signal analyzer and ARB based generator functionality. The compact integrated solution can be customized with up to three R&S®CMPHEAD30 remote radio heads (RRH), for up/downconverting signals to 5G FR2 frequencies.
-
Product
Multifunction Digital Tester
-
*Contact ACV test*Non-contact ACV test*Continuity check*DC Voltage / Polarity check
-
Product
Contunuity Tester With Audio Warning
CT-01
-
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Graduall
-
Product
PC Crush Tester
DRK113E
-
Shandong Drick Instruments Co., Ltd.
DRK113E Crush Tester PC is a high accuracy and intelligent instrument, designed according relevant standards. The advanced components, mating parts and micro-computer are logical structured, to ensure the property and appearance.The instrument has parameter testing, adjusting, computer screen display, memory, printing function.
-
Product
Automotive Engine Tester
QCM-2A
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This tester is applied to integrated test varieties of automobile motor, wiper motor, window lifting motor, oil pump motor etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stators.
-
Product
Lan Cable Tester
185 LCT
-
Standard Electric Works Co., Ltd
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable. The LAN cable tester can verify cable continuity, open, short circuit and miss-wired. The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels. Auto and manual scan functions. Ground wire test. Lock status function. Buzzer sound warning for wire status. Display : LED indication for wire status.
-
Product
Environmental Testers
-
Our range of environmental test equipment provide users to test and measure all aspects of the environment. The comprehensive range includes temperature, infra red, sound level, humidity, LUX level and air flow.
-
Product
Ultra Fast Digitizer With 8 Bit, 4 GS/s Sampling Rate With Up To 8 GS Memory
CompuScope Express 14G8
-
The CobraMax CompuScope family of GaGe ultra high-speed 8-bit digitizers provides the most powerful combination of speed, memory, and bandwidth as well as a wide portfolio of advanced acquisition features on a single PCI Express or PCI card.
-
Product
Heavy Duty Circuit Tester
28400
-
A heavy duty circuit tester for lifetime use. The probe, handle, cord and clamp are reinforced for extra durability. Comes with a strain relief spring on the cord. Cord is 49".
-
Product
Igniter Testers
-
Igniter Tester is a failsafe and portable digital ohmmeter specifically designed for ultra-safe resistance testing on squibs, flares, bridge-wire, and other explosive devices. The 620A-4 ohmmeter has been approved by the USAF Non-Nuclear Munitions Safety Board for usage on all non-nuclear munitions, and independently certified to meet Mil. Std. 810 Mtd. 511 for usage in fuel-filled environments. Due to its intense self-safety design and numerous certifications, the 620A-4 failsafe ohmmeter is the industry standard for military programs in need of igniter testing.
