-
product
Needle Microprobe
MT-26/4HT
Fast-response 26 gauge needle probe, (needle length is 4 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Needle Microprobe
MT-26/6HT
Fast-response 26 gauge needle probe, (needle length is 6 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Flame Spectrometer
The Flame spectrometer is built using industry-leading manufacturing techniques that help deliver high thermal stability and low unit to unit variation without compromising the flexibility and configurability that are the hallmark of Ocean Optics miniature spectrometers. New features such as interchangeable slits, indicator LEDs and simple device connectors deliver more freedom and less frustration.
-
product
Needle Microprobe
MT-29/5HT
Fast-response 29 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
HMV Horizontal Flame Chamber - Motor Vehicles
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
product
UV/IR Flame Detector for Hydrogen Apps
The FL500-H2 is an Ultraviolet / Infrared flame detector designed specifically to detect hydrogen (H2) fires. The FL500-H2 optical flame detector monitors for radiation emitted by a hydrogen flame in both the ultraviolet (UV) and infrared (IR) spectral ranges.
-
product
OptiStroke™ Needle Stroke Detection System
The patented OptiStroke system reduces product waste and confirms hot melt adhesive dispensing performance by verifying valve actuation and fatigue. Ideal for applications where product-yield loss is critical, the system is compatible with Nordson Universal™ modules, Speed-Coat™ modules and Harmony modules.
-
product
Needle Microprobe
MT-D
Fast-response 29 gauge needle surface probe for locating inflammation, arteries, etc. Also for dental use. 1/4'' right angle needle length, 3/4'' needle distance from lead. 5.5'' long handle for ease of use. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Sensor within .3mm of tip. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
UV/IR Wet Bench Flame Detectors
SMC 3200/3300
The SMC 3200/3300 Series Flame Detectors utilize proven, stable UV/IR technology to continuously monitor for flames in wet bench and commercial applications. Due to its compact size, it is also used for installation in certain production equipment.
-
product
Wire Probe Needles Materials & Pin Diameters
Advanced Probing Systems, Inc.
Tungsten pins and tungsten-rhenium pins can be provided with either nickel plating or silver plating. Beryllium-copper pins are supplied with a silver plating coating.
-
product
Flame Testing
Helping you ensure acceptable flammability and flame resistance for electronic products and components.
-
product
Palladium Alloy & Beryllium-Copper Probe Needles
Advanced Probing Systems, Inc.
APS has been providing high precision, high volume Tungsten Electrosurgical Needles for over 20 years in Colorado where the product was invented. Our unique Chemical machining process can produce polished electrosurgical needles for diameters from .177mm to .711mm. Overall lengths produced from 25.4mm to 38mm. Tip sizes range from .001mm to .115mm.
-
product
Flame Ionization Detector
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
product
2.5mm Test Rod Test Probe Needle
CX-4C
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test rod test probe needle Used to verify the protection of persons against access to hazardous parts.
-
product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
product
Needle Microprobe
MT-29/3HT
Fast-response 29 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Needle Pressure Gauge
102
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
product
Cross Needle Meter. 1.8 - 60/144/440
MFJ-864
This new MFJ Cross Needle SWR/Wattmeter covers HF thru VHF 1.8 - 60MHz, 144 MHz and 440 Mhz bands. It features separate HF and VHF / UHF directional couplers, each with its own SO-239 connectors. This lets you connect your HF and VHF/UHF transceivers at the same time.
-
product
Probe Needles for Wafer Sort and Test Applications
Advanced Probing Systems, Inc.
APS is the global leader in the manufacture of probe needles used in cantilevered probe cards. All probe needles used in wafer sort are manufactured according to customer specifications using stringent in-process quality assurance procedures.
-
product
Needle Microprobe
MT-29/2HT
Fast-response 29 gauge needle probe, (needle length is 2cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Needle Microprobe
MT-29/1HT
Fast-response 29 gauge needle probe, (needle length is 1cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Flame & Other Plastics Testing
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
product
Flame Burning Tester
DRK3024A
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
product
Masks Flame Retardant Performance Tester
WKS-1208
WKS-1208 Masks Flame Retardant Performance Tester is used to test the burning performance of the mask after contacting the flame at a certain linear velocity. It is special test instrument for the flame retardant performance of masks.
-
product
Thermal needle system thermal resistivity / conductivity measurement
MTN01
Hukseflux Thermal Sensors B.V.
The MTN01 Multi-purpose Thermal Needle System allows performing fast measurements of the thermal resistivity or conductivity of soils. It is specifically designed to be reasonably robust, as well as accurate. It is therefore suitable for laboratory as well as field- measurements of soil thermal properties. The sensor is a Non-Steady-State Probe (NSSP), TP07, which is mounted on the Insertion Tool, IT02. The system is operated using a hand-held Control and Readout Unit CRU01.

























