Serial Interfaces
one conductor one bit at a time data transfer.
See Also: Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, PXI Serial Interfaces, Parallel Interfaces
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - XMC
Model 71660
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
SparkFun Spectral Sensor Breakout
AS7262 Visible (Qwiic)
-
The SparkFun AS7262 Visible Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7262 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board --- simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic Shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
-
Product
SPI Isolators
-
SPI (Serial peripheral interface) is one of the most widely used interfaces between microcontrollers and peripheral ICs such as sensors, ADCs, DACs, shift registers, SRAM, and others. Analog Devices has your isolated SPI bus covered with our dedicated SPI digital isolators which support this synchronous, full duplex master-slave-based interface. Options include devices built with ADI's proven iCoupler® technology and offering a small footprint, simple design-in, fast speeds, and high data integrity, as well as integrated µModules which require no external components. Our SPI isolator solutions increase performance and reduce board space. This simple, compact solution is ideal for isolated SPI data requiring communication across different ground potentials or through large common mode transients often found in Industrial PLCs (programmable logic controllers) and Instrumentation and data acquisition systems.
-
Product
PXI-8430, 4-Port, RS232 PXI Serial Interface Module
778983-01
-
4-Port, RS232 PXI Serial Interface Module - The PXI‑8430/4 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 3U VPX
Model 52741
-
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 4 GB of DDR3 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration ManagerSynchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Area Scanners
-
Leuze electronic GmbH + Co. KG
These devices scan their environment using a quickly-rotating laser measurement beam. This allows them to detect objects even at long distances. With an opening angle of 190° and a measurement distance of up to 65 m, the laser scanner can monitor an area of one hectare. Object detection occurs in parallel in up to 4 detection fields. Convenient configuration software RODsoft permits the parameterization of 8 detection field pairs and 4 detection fields. The status output takes place via a serial interface and an optional warning output. Should service be necessary, the device can be swapped out and put back into operation extremely quickly thanks to the ConfigPlug configuration memory.
-
Product
Extension Module
GE-AI-4
-
Infinite Industrial Informatics Lt
GE-AI-4 is a DIN rail mount, analog input expansion module with I2C serial communication interface. It can be used for the analog input expansion of Infinite's products as the SCOM-100 GSM controller and the iLOGPlus RTU/Data Logger.
-
Product
L-Band RF Tuner and 4-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 58690
-
- Two L-Band tuners accept RF signals from 925 MHz to 2175 MHz- Two programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- Two programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Four 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI-8433, 2-Port, Isolated, RS485/RS422 PXI Serial Interface Module
779744-01
-
2-Port, Isolated, RS485/RS422 PXI Serial Interface Module - The PXI‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Real-Time Clock (RTC) ICs
-
ST offers a wide portfolio of real-time clock (RTC) ICs with parallel or serial interface, including ultra-low-power devices and the world’s smallest package with embedded crystal. Our devices offer many value-added features such as supervisory functions that include alarm, battery switchover, and reset as well as special features with time stamp, anti-tamper for secure applications and an integrated audio section.
-
Product
Intelligent Power Monitor
iPM
-
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
Product
Serial Device Server
SD-330AC-1402
-
The Silex SD-330AC-1402 features a FIPS 140-2 wireless/wired LAN Serial Device Server and an Ethernet to Wi-Fi Bridge. Devices equipped with the RS-232C serial interfaces can join a Ethernet LAN or wireless LAN. Devices with an Ethernet port are also transformed to a wireless network devices. Medical devices, printers, scanners or virtually any other device with a serial port or an Ethernet port can now be enabled with secure and robust LAN network capability. The SD-330AC-1402 can be simply added to US government facilities to enhance device networking connectivity.
-
Product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
-
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Serial And Parallel Port For PCIe
DTA-2142
-
Serial and parallel interfaces for ASI and SD-SDI, supporting multiple electrical standards including M-LVDS and LVTTL. Clock rates up to 108MHz are supported.
-
Product
USB-232, 1-Port, USB, RS232 Serial Interface Device
778472-01
-
The USB‑232 interface transforms your USB port into a single asynchronous serial port for communication with RS232 devices. You can use a USB‑232 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCI Express 16-Port RS-232 Serial Interface
7161e
-
The 7161e provides sixteen RS-232 serial ports capable of data rates to 460.8K bps. Each RS-232 port implements all modem control signals for maximum compatibility with a wide range of peripherals. The board is PCI Express X1 compliant and utilizes 16C854 UARTs to provide 128-byte Tx/Rx FIFOs for maximum reliability in data intensive applications.
-
Product
Ethernet-GPIB-USB to Serial Interface
Model 9006
-
* All interfaces provide full communication with the serial device.* Ethernet port supports VXI-11 and raw socket protocols.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* GPIB port is IEEE-488.2 compatible.* USB port uses Microsoft supplied driver to prevent driver problems with operating system change problems.* Serial port provides RS-232 and 2 or 4-wire RS-485 signals.* Supports devices that generate asynchronous messages, devices that respond when queried and smart devices.* Internal webserver for easy configuration from any browser.* Board runs on 5 to 15 Vdc power.* Includes ICS's VXI-11 and VISA keyboard control programs.* Works with Agilent, NI and Kikisui VISA libraries.
-
Product
Multiplexer 2:1 With De-Emphasis 32 Gb/s
M8062A
-
R&D and test engineers who need to characterize serial interfaces of up to 32.0 Gb/s can use the M8061A 2:1 Multiplexer with optional de-emphasis to extend the rate of J-BERT M8020A and J-BERT N4903B pattern generator. For the most accurate receiver characterization results, the M8061A provides four calibrated de-emphasis taps, which can be extended to eight taps, built-in superposition of level interference and Clock/2 jitter injection. The M8061A is a 2-slot AXIe module that can be controlled via USB from the user interface of J-BERT M8020A as well as N4903B.
-
Product
PXIe-8431, 8-Port, RS485/RS422 PXI Serial Interface Module
781473-01
-
The PXIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
-
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Serial to Digital Interface
-
All of ICS's Serial Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - XMC
Model 71741
-
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 4 GB of DDR3 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Clock up to four modules with Model 7194 High-Speed Clock Generator - PMC/XMC- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
-
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
Product
SDI Cable Drivers
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a wide range of products specifically designed for driving Serial Digital Interface (SDI) video signals across long copper cables. These multi-rate products are the ideal solution when designing high definition (HD) and ultra high-definition (UHD) video broadcast equipment and are fully compliant with the Society of Motion Picture and Television Engineers (SMPTE) standards.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 6U VPX
Model 57760
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PCIe Based FPGA Processing / Acceleration Card
-
iWave’s PCIe based FPGA Processing / Acceleration Card is a half-length PCIe x4 card featuring a high-performance user-configurable Xilinx® Kintex®-7 FPGA enhanced with high-speed memory and a high-throughput serial interface. Front I/O adds dual SFP ports, 1x HDMI1.4a IN, 1x HDMI1.4a OUT. All of these features combine to make the card ideal for a wide range of applications such as Edge Computing, ARINC818 Avionics Video Bus, Acceleration.
-
Product
1 GHz A/D and D/A with Virtex-7 FPGA - XMC
Model 71730
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual uSync clock/sync for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
