- CAMI Research Inc.
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty cri...show more -
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
product
Wristat Tester
WT25
The WT25 WRISTAT Tester is designed to test the integrity of our WRISTAT in a fast, efficient and simple manner. All of the elements of the WRISTAT - continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact are easily confirmed by pressing the top cover of the WT25. The operator (wearer) is tested for a resistance to ground of greater than 750K ohms and less than 10M (switchable to 100M ohms).
-
product
5 kV AC Hipot Testers
Models M100BVS5 & M500BVS5
Now you can perform safe, rapid and efficient hipot testing, ground continuity testing, and total or real current monitoring in one simple operation. The ROD-L Electronics model M100BVS5 and model M500BVS5 hipot testers perform safe and accurate AC hipot and ground continuity testing in compliance with UL, IEC, CSA, VDE, FCC and other electrical equipment testing standards
-
product
Breakout Box
T1000-9
T1000-9 breakout box is our most compact breakout box, using dual 9 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 18 test points plus a ground jack. All test points use standard size 4mm banana jacks. Ideal for continuity testing, isolation testing or signal capture and monitoring.
-
product
Hipot Line Testers
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
product
SAFE-T-GROUND - Ground Continuity Monitor / Control
TR-7
Model TR-7 Safe-T-Ground provides continuous monitoring of a truck's ground connection throughout loading operations. Static electricity is often brought in by tank trucks entering the loading area. The Safe-T-Ground Model TR-7 instantly stops loading operations if a tank truck loses its ground.
-
product
ELECTRICAL TEST Kit
1021 TK
Standard Electric Works Co., Ltd
2950 CL ● Pocket size.● 4000 counts.● Full automatic measurement : Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (auto off in 1 minute). ALS-2 ● Use with any clamp meter.● x10 mode allows for more accurate measurements of low amperage devices.● x1 mode allows for direct reading.● 4mm voltmeter input jacks.● Integrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
product
DC Hipot with Insulation Resistance Tester
297
Our Model 297 is a simple-to-use Hipot Tester with the built-in ability to easily test Insulation Resistance and Ground Continuity (Low Current Continuity) in a one-box solution. The 297 is capable of performing Hipot Tests in both AC & DC currents. Make testing simple with common sense security settings. PLC Remote allows you to make Hipot Testing safer with Personal Protective Equipment (PPE).
-
product
Self-reclosing Overcurrent And Residual Current Protection
Wide range of solutions to guarantee personnel safety as well as maximum service continuity in the event of a ground current or breaker trip, with automatic reconnection of the installation. Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
product
Multi-purpose Cable Tester and Cable Tracer
165 CB
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
product
Multifunctional Safety Tests
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
product
Multi-Network Cable Tester
3PK-NT007N
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
product
DC Hipot Test Instrument
M100DC
Performs concurrent ground continuity test. ARC and OVERCURRENT detection circuits. Fast discharge of Device Under Test (DUT) and other test standards
-
product
8 Plug Pro Audio Cable Tester
PCT10
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections3.5mm TRS Jack1/4' TRS Jacks3 Pin XLR Male3 Pin XLR FemaleRCA Phono4 Pin SpeakonBanana Plugs9V Batter (Not Included)
-
product
Cable Tracer and Digital Multimeter
187 MCT
Standard Electric Works Co., Ltd
Lan Cable Tester● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.● The LAN cable tester can verify cable continuity, open, circuit and miss-wired. ● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan function.● Ground wire test.● Display : LED indication for wire status.Digital Multimeter● 4000 counts LCD.● Full automatic measurement. Voltage measurement. Resistor measurement.● Range change function.● Select function.● Data Hold function.● Continuity check.● Diode measurement.● Low battery indication.● Input impedance:10MΩ.
-
product
High Resistance Neutral Grounding Devices
HRG systems limit the fault current by placing high resistance between neutral point of transformer (or generator) and ground. As it is not possible to locate the fault point in delta connected systems, an artificial neutral point is created and delta connected system can be grounded. This allows a fault current of a few amperes thus locating the fault point gets easy. When the neutral point is grounded thru high resistance, both continuity of operation is provided during fault condition and sufficient current (typically between 2 A and 10 A) flow is provided for ease of locating the fault point.
-
product
Automated AC Digital Hipot Tester
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co. KG
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Ground Continuity Tester
HTDT-10A / 740
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for testing the conductivity of the connecting part of power equipment and ground network in engineering test of power department.
-
product
Variable Power Supply
VS3
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use ...show more -
product
Breakout Box
T1000-62HD
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
product
DC Hipot Tester
296
Our Model 296 is a simple-to-use Hipot Tester with the built-in ability to easily test Ground Continuity (Low Current Continuity). The 296 is capable of performing Hipot Tests in both AC & DC currents. You need a Hipot Tester that includes all the features you need to get the job done, the 296 has what you're looking for Make testing simple with common sense security settings.
-
product
Ground Continuity Test Instrument
MODEL M25
Performs ground continuity tests in full compliance with BSI, VDE and IEC. Measures AC resistance from Chassis of Device Under Test (DUT) to power-cord ground lead - 0 to 0.15 ohm
-
product
Automated Digital Ground Continuity Tester
Educated Design & Development, Inc.
1 Button Testing - No setup required, just plug right in!Digital LED display reads out in OhmsAlso performs the Low Current Ground Continuity test, at the same time!Auto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchCustom universal receptacle accepts both 120V and 240V plugs.Zero feature allows you to "zero-out" the test lead impedance.Meets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements.
-
product
Ground Leads Continuity Tester
Weshine Electric Manufacturing Co., Ltd
1. The new power supply technology is adopted in the grounding down lead conduction tester.2. It has the characteristics of small size, light weight, large output current, good repeatability, strong anti-interference ability and protection function. 3. The whole machine is controlled by single chip microcomputer, which has a high degree of automation. 4. The instrument has high precision and easy operation. The maximum current is 10A.
-
product
Visual Fault Locator
HW-205
Shanghai Fibretool Technology Co.,Ltd.
The HW-205 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.- 2.5mm universal connector- Operates either in CW or Pulsed- Constant output power- Long battery life (up to 60 hours)- Laser case ground design prevents ESD damage- Portable and rugged, easy to use- Burning testing to ensure the reliability.- Optional 1.25mm connector adapter
-
product
Networked Data Logging System
Model - MC60
Provides data-logging and remote control from networked PCs. The MC60 safety test management system greatly reduces the time and costs associated with monitoring, recording, and validating the electrical safety test compliance information from a ROD-L hipot or ground continuity tester.
-
product
Wristat Tester
WT 25-4145.26M
WT 25-4145.26M Wristat Tester is available to comply with D.O.D. 4145.26 specifications. The WT25-4145.26M Wristat Tester is designed to test the integrity of our WRISTAT in a fast, efficient, and simple manner. All the elements of the WRISTAT – continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact – are easily confirmed by pressing the top cover of the WT25-4145.26M. The operator (wearer) is tested for a resistance to ground of greater than 250K o...show more -
product
12 Plug Pro Audio Cable Tester
PCT40
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections
-
product
Protector Conductor Test / Ground Continuity Test / Ground Bond Test
Testing the protective conductor is indispensable for assemblies, devices and systems of protection class I because it reduces the risk of life-threatening electrical accidents.The test checks whether the protective earth (PE) fulfils the criteria specified in the standards and can correctly discharge the current occurring in case of a fault.The ground continuity test checks whether the protective earth conductor is connected continuously to all metallic enclosure parts that can be touched by the user. The test can be carried out with low currents and voltages (simple continuity test).
