Showing results: 2581 - 2595 of 5238 items found.
-
151733-0R3 -
NI
8-Pin Male Ethernet to 8-Pin Male Ethernet, CAT-5E Ethernet Cable - The 8M-8M Ethernet Cable connects devices to network hubs or switches. The cable has straight-through wiring and is available in different lengths and thin profile options.
-
151733-01 -
NI
8-Pin Male Ethernet to 8-Pin Male Ethernet, CAT-5E Ethernet Cable - The 8M-8M Ethernet Cable connects devices to network hubs or switches. The cable has straight-through wiring and is available in different lengths and thin profile options.
-
H5421 -
COMET SYSTEM, s.r.o.
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
T5441 -
COMET SYSTEM, s.r.o.
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
H5321 -
COMET SYSTEM, s.r.o.
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
H5021 -
COMET SYSTEM, s.r.o.
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
T5341 -
COMET SYSTEM, s.r.o.
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
-
-
Metrix
Metrix* proximity vibration transmitters are compatible with Bently Nevada** Series 3300, 7200, and 3000 probes and cables as well as our own probes and cables. The flexible Metrix MX2034 Transmitter can be reconfigured to handle any of these probe / cable combinations.
-
Qbox -
Whirlwind Music Distributors, Inc.
The Qbox is the all-in-one audio line tester ideal for applications such as live sound, maintenance, installation work - anywhere audio runs down a cable. The Qbox can quick-check dynamic microphones and cables without firing up the entire system. It provides a handy mic or line-level tone for activating a signal path or identifying a specific cable in a pile of cable ends.
-
Tracy -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
PGK 25 -
BAUR Prüf- und Messtechnik GmbH
Cable testing with the BAUR PGK 25. Cables must be tested in compliance with the national and international standards. This applies before the commissioning of new cable networks. The portable BAUR PGK 25 cable test device is used for DC voltage testing in low- and medium-voltage cables. It is characterised by its low weight of only 16.5 kg, by the easy operation and solid construction for onsite use.* Compact device for DC voltage testing with negative polarity* Continuously adjustable output voltage* Perfect for mobile use
-
60-984-001 -
Pickering Interfaces Ltd.
The 60-894 provides a simple an effective method of joining two LXI WTB bus cables together to extend the length of available cables. It is an ideal solution for cable extension where users need to experiment with different cabling solutions without having to totally replace the cables in the system. The 60-894 provides mating connectors for the WTB on each end connected together by a set of accurate differential transmission lines to avoid additional reflections on the cable. The 60-894 is entirely passive and is compatible with the LXI specification.
-
IRG 4000 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR IRG 4000. The IRG 4000 time domain reflectometer is integrated in BAUR cable fault location systems and is used in combination with the system software for locating cable faults in single and three-phase cable systems. Thanks to the novel operational concept, cable faults can be located more rapidly and easily with IRG 4000. The high-performance industrial PC and improved measurement parameters allow for a precise cable fault location in all cable types. The well-proven and continuously enhanced methods are available for the cable fault location as well as the newly developed Conditioning SIM/MIM** method which makes it even more effective and quick to locate wet cable faults that are difficult to detect. The SIM/MIM technology with 20 reflection measurements per HV pulse allows for selecting the best reflection image for a very precise determination of the fault distance.* Easy operation thanks to intuitive operational concept*Maximum precision with high resolution and sampling rate*Precise fault location methods for every type of fault