Classification
order by relation to shared values.
-
Product
Entry Level AOI
iSpector
-
The Mek iSpector series AOI machines are fully compatible with Mek’s Catch System for classification, repair and SPC, utilizing the same powerful 22X software that is used in the premier Mek PowerSpector series. There is no compromise on the wide range of inspection algorithms and component libraries.
-
Product
IP65 High Accuracy Temperature & Humidity Sensor
96PD-THS16B
-
Metal probe reduce electromagnetic interference0 ~ 100%RH measurement-40 ~ 120°C Temperature Measurement RangeIP65 Housing Classification
-
Product
Supply Chain Management
-
200 Customers100 Active SuppliersPurchasing for 60 material classifications including such materials as:a) IC, Resisters, Capacitors, Wire, Cable, Power Suppliesb) Connectors, Converters, Diodes, Fuses, Fabricated partsc) Inductors, Relays, Switches, Hardware
-
Product
Electrical Safety Test Equipment
-
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
Product
pyranometer
SR20
-
Hukseflux Thermal Sensors B.V.
SR20 is a pyranometer of the highest category in the ISO 9060 classification system: secondary standard. This solar radiation sensor is used where the highest measurement accuracy is required. It measures the solar radiation received by a plane surface, in W/m2, from a 180o field of view angle. SR20 secondary standard pyranometer enables you to attain the highest measurement accuracy and excels in demanding applications. After a thorough programme of acceptance testing, SR20 was released February 2013.
-
Product
CDM testers
Scorpion
-
Scorpion opens a new generation of CDM testers. It is designed to meet the new JS-002 standard and features Contact First pulse delivery. This patent pending technique of Contact CDM (CCDM) meets the latest CDM standards with higher accuracy for device classification.
-
Product
Multibeam Echosounder - Deep Water
HydroSweep MD/50
-
The HydroSweep MD/50 is a high resolution multibeam echosounder ideally suited for seabed mapping in mid and shallow water based on a sonar frequency range between 52 kHz to 62 kHz. Beside bathymetric depth information from 5 m to more than 2000 m, sidescan data and backscatter data for seabed classification can be acquired.
-
Product
Adhesion Test Analyzer
PA-917010
-
The Adhesion Test Analyzer (ATA) takes all of the guess work and subjectivity out of rating the classification of your adhesion results as defined in the ASTM D3359 standard, and is accomplished with one simple instrument.
-
Product
Moisture Management Tester
-
Sataton Instruments Technology CO., Ltd
Moisture management tester (MMT) is the tool for the measurement, evaluation and classification of liquid moisture management properties of textile fabrics. By testing the changes in electrical resistance of textiles placed between two horizontal electrical sensors with concentric pins, the tester can calculate fabric liquid moisture content changes that quantify dynamic liquid moisture transport behaviors in multiple directions of the specimen. The software of tester can grade the liquid moisture management properties of a fabric by using the predetermined indices. The tester is used to determine the liquid moisture management properties of knitted, woven and nonwoven textiles, and also can be used to test the one-way transport capability of diapers.
