PCB Adapters
-
product
PCB Test Points and Terminals
Our PCB test points and terminals feature a large loop for easy probe attachment or to facilitate the clipping on of other components. They are ideal for components which need frequent replacement and are also suitable for raising hot components above the surface of the PCB.
-
product
Calibration Hex Step Adapters
When performing torque wrench calibration or testing, adapters are often needed, especially with torque wrenches that have open-end heads. Mountz’s calibration hex step adapter features four common sizes, which will increase the productivity of your torque wrench calibration process. This adapter will make testing and calibration simple and efficient.
-
product
PCI Adapter for cPCI
PCI2cPCI
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
PCB Connectors
HDLP Series
Smiths Interconnect's HDLP series is a low profile, high density interconnect with integral sealing
-
product
Control Board For Testing PCBs
TCC 1800
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
product
XMC-to-PCI Express Adapter
7768
The Technobox, Inc. P/N 7768 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module with VITA 61 (XMC 2.0) style connectors in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors.
-
product
Signal & Power PCB Connector
HPW Series
Smiths Interconnect's HPW series is a versatile interconnect with mixed signal and power contacts, up to 15A each
-
product
37-Pin D-Type Male Straight PCB Mount
40-963-037-SM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
XMC-to-PCI Express Adapter
7764
The Technobox, Inc. P/N 7764 XMC to PCI Express Adapter permits the use of a single-wide XMC module with VITA 61 (XMC 2.0) style connectors in a 8x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors.
-
product
Emulation Adapters
With some of the more advanced 32-bit microcontrollers and SoCs, the full program and data trace capabilities of the device are not made available on production silicon. Instead, semiconductor vendors provide special 'emulation devices'. These typically feature more pins than the production device, thereby providing the interface to the trace interface.
-
product
37-Pin D-Type Male Right Angled PCB
40-963-037-RM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Tool, Press Kit, i2 PCB Headers
910121199
Tool, Press Kit, i2 PCB HeadersAids in pressing fit pins into the header.
-
product
Multiport Serial Adapter, PCIe X4
PCI325
The PCI325 is an RS-422 synchronous/asynchronous multiport serial adapter. The module can accept a clock input to synchronize the baud rate generators of each port to an external clock. All the protocol management overhead is taken care of in the hardware so that the host CPU is offloaded from managing the detailed serial protocol. An I/O breakout box may be connected to the high-density connectors of the PCI325 to provide multiple DB25, DB9, or other serial connectors for easy integration to your system or an octopus-style breakout cable may be used. The I/O breakout box may include many different status LEDs which can be tailored to your protocol/application. The PCI325 provides the breakout box with power so that it does not require any additional power cabling
-
product
XMC-to-PCI Express (PCIe) Adapter
9956
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
product
78-Pin D-Type Female Straight PCB Mount
40-963-078-SF
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
BGA Socket Adapter Systems
Advanced Interconnections Corp.
BGA Socket Adapter Systems convert surface mount device packages to through hole (pinned) assemblies, making it easy to plug and unplug SMT devices whether you are planning for future device upgrades, field programming at point of use, or need the ability to quickly swap out device packages in the field or the test lab. Protects valuable PC boards and saves time by eliminating the need to desolder packages during device removal.
-
product
RF Adapters
SMPM Adapters
a type of blind-mate, push-on connector that is similar to SMP connectors.
-
product
PCIe Adapter for XMC
PCIe8LXMCX1
Simple and easy to use. Install PCIe8LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position.
-
-
-
product
Camera Interface Boards and Adapters
Active Silicon offers camera interface boards for autofocus-zoom block cameras and adapters for host-end acquisition and video format conversion. The camera interface converter boards for Tamron AF-zoom cameras, Sony FCB block cameras, Harrier AF-zoom cameras and others, take data from the proprietary block camera interface and convert into industry standard formats such as 3G-SDI / HD-SDI, USB 3.0, HDMI and IP.
-
product
PCF79xx Adapter Xhorse
For recoverring used keys BMW series E and F. More advanced users – we can use renew key for LandRover, Chrysler, Dodge
-
product
Miniature Amplifier PCB
Sized for single channel TO-5 packages and electrically compatible with all Dexter Research Center detectors. Available in three amplifier gains: 300, 500 and 1,000 providing convenient buffering and pre-amplification of thermopile signal. Facilitates fast R&D startup time that can be integrated into your prototypes or final system design.
-
product
XMC-to-PCI Express (PCIe) Adapter
8366
The Technobox, Inc. P/N 8366 Compact XMC-to-PCIe (PCIe) adapter permits use of a standard VITA 42.3 air-cooled XMC in the smallest possible edge finger PCIe form factor. The length of the adapter is the length of the XMC, while the height is a standard PCIe board, not the low-profile version. It provides up to eight lanes (8X) from the XMC's P15 connector to the edge fingers.
-
product
BGA Socket And BGA Adapter Systems
Mill-Max's BGA Socket/Adapter Systems are used for both socketing BGA devices and interconnecting circuit boards. Systems are available to fit 1mm, .050" and .8mm grid footprints.
-
-
product
PCIe Adapter for 3 IP Modules
PCIe3IP
IndustryPack® Modules are an important part of solutions for Embedded situations. Rugged, small, light ... just right for many applications. IndustryPack® Modules require a carrier to adapt them to the system. Dynamic Engineering has carrier solutions for a variety of formats. PCIe3IP is designed to support PC computer based solutions. Solutions available for PCI, PC104p, cPCI, VPX and planned for cPCIexpress, PC104e.
-
product
PCB Test Fixture Kits
Emergent's fixture kits are available in bottom and double sided probing versions. They are fully scalable, from compact benchtop testers to full size multi-UUT production floor models. The removable, interchangeable plate design allows you to easily add and move test points, or swap out plates to test a completely different product. Each kit comes with a standard linear collapse over-clamp. A cam-follower closing system can be specified for higher force applications. Our fixture kits are manufactured using industrial grade phenolic laminate, which is similar to G10 in hardness and strength but easier to machine. The standard kit comes pre-assembled with blank plates for machining.
-
product
37-Pin D-Type Female Right Angled PCB HV
40-963-037-RF-HV
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Tesla Meters & Adapters
Projekt Elektronik Mess- und Regelungstechnik GmbH
Magnetic field measuring devices, also known as magnetometers or gaussmeters, which we market under the product name Teslameter, together with one of our probes, form the individual solution for a measurement task. The basic principle at Projekt Elektronik is the modular structure, which allows the combination of different probes with a magnetic field measuring device. This means that our components can be flexibly adapted to the respective requirements. A great advantage for the everyday practice of our customers.
